Re: [motm] Hats vs shirts
2000-03-15 by J. Larry Hendry
Oops, supposed to be private. OK, now you all know. I AM BUYING A HAT ! Larry (will look good in a hat) Hendry
Messages
Browse messages
Page 608 of 690 · 34488 messages matched
Re: [motm] Hats vs shirts
2000-03-15 by J. Larry Hendry
OK, I ll take a hat. Include it with my 440 filter. Charge my card accordingly. Do you want me to fill out an order form? Larry H ... synthesizers
Apologies to Nathan
2000-03-14 by J. Larry Hendry
Sorry, I did a quick respond to instead of going to the address book and inadvertently left Nathan s note attached. The big Stooge Hendry
Hats vs shirts
2000-03-14 by Paul Schreiber
Due to many factors, the shirts won t have the analog modular synthesizers stitched in. The hats will. Paul S.
Problems with the PAiA VCA
2000-03-14 by J. Larry Hendry
An excerpt from synth-diy, for those of you that do not describe. In the world of kits, you have MOTM and then the other guys.... the names have been removed
Nevermind this message
2000-03-14 by Nathan Hunsicker
Hi everyone, my email has been down for about a week, I just wanted to make sure I am still a member of this group. -Nate
MOTM GearWear
2000-03-14 by Paul Schreiber
Hey, Kids! Be the first on your block to own expensive modular synths AND expensive stuff to wear! Offering the following: MOTM black brushed twill cotton hat
RE: [motm] duh - remind me about another VCA?
2000-03-14 by David Bivins
Thanks everyone for the info! I m sure Paul will chime in with how far down it is in his pile of upcoming modules... ;)
Re: [motm] duh - remind me about another VCA?
2000-03-14 by J. Larry Hendry
This is the information I last recall reported about the upcoming Ultra VCA. Much of this was cut and pasted from the actual announcement to the MOTM list
RE: [motm] duh - remind me about another VCA?
2000-03-14 by David Bivins
O.k. Anyone remember when it might come out? THanks Ken! David.
duh - remind me about another VCA?
2000-03-13 by David Bivins
Hey all, What s the next VCA design coming around and when? I m debating whether to buy a second 110 (with a second ringmod I may not use much) or wait for
RE: [motm] duh - remind me about another VCA?
2000-03-13 by Brousseau, Paul E (Paul)
From an e-mail back in late January, Paul S. reports May-ish . Price range $189-209. (See e-mail thread subject ATTENTION: Quad VCA still available! .)
RE: [motm] duh - remind me about another VCA?
2000-03-13 by Tkacs, Ken
If I remember correctly, it was an Ultra Dual VCA: separate lin/log inputs, panning, cross-fading, and mixing. Very very stable, very difficult kit. ... From:
Re: [motm] vco
2000-03-13 by Chad Conger
I just use Cool Edit - a program that came free with my sound card, which has a cool green scope-like display of incoming digital sample.. works good enough
Re: [motm] vco
2000-03-13 by velure
i m a pretty well seasoned electronic tech, so the more complex the project, the better. i was just worried i might need a scope to set offsets or things like
RE: [motm] vco
2000-03-13 by Tkacs, Ken
I built three MOTM-300 VCOs and adjsuted the sine symmetry by ear in each case. Later I hit them all with a borrowed scope and all three were set correctly. So
Re: [motm] vco
2000-03-13 by Aardvark1@aol.com
In a message dated 03/12/2000 10:03:58 PM Eastern Standard Time, velure@surfnj.net writes:
MOTM-440 demos
2000-03-13 by Paul Schreiber
Thanks to David Bivins for these MOTM-440 demos: www.synthtech.com/news Paul S.
Re: [motm] vco
2000-03-13 by J. Larry Hendry
The only thing you could need the scope for on the VCO is the SINE wave shape trimmer. However, you can set this by ear and it seems to run about it the
vco
2000-03-13 by velure
what do i need to build the VCO? i only have a multi-meterl, no o-scope. should i just have paul build it so i know it s right? -steve
Re: [motm] EMS Vocoder
2000-03-12 by Paul Schreiber
I ll those and any others laying about! Paul S.
Re: [motm] EMS Vocoder
2000-03-12 by Ben Vehorn
I might, but will have to check when I get home in a couple of weeks (I m out of town)... I do have schematics for the Sennheiser Vocoder--let me know if you
Re: [motm] Pulse Divider again...
2000-03-12 by Hugo Haesaert
Hi All ! My Roland system 100 adsr s expect something like 12-13V as gate in . Give em less and they will still trigger, but not peak properly . And i thought
RE: [motm] MOTM-440 info + pix
2000-03-12 by Tkacs, Ken
So, in summary, this mishap makes no difference to the final product--it s strictly a behind-the-scenes thing, right? ... From: Paul Schreiber To: MOTM
MOTM-440 info + pix
2000-03-12 by Paul Schreiber
If you received the previous broadcast email, I discovered a misplaced mounting hole in the MOTM-440. The solution will be to add an additional hole in the
RE: [motm] Patch Diagramming Revisited
2000-03-12 by Tkacs, Ken
I m so glad you pointed out the droopy patchcord connector! It makes hell of difference, as my old design teacher, Mr. Tomasewski, used to say! I don t
MOTM-110 and 800 modifications
2000-03-12 by J. Larry Hendry
Last September, Paul sent out some factory approved modifications for the MOTM-110 VCA. He clearly stated that your results might vary since the 100 K pot
Re: [motm] Router Weirdness
2000-03-12 by J. Larry Hendry
Another thing to check is R10 and R11. If these are not the same size, that could skew the center point of VR1. Larry H
Re: [motm] Patch Diagramming Revisited
2000-03-12 by Aardvark1@aol.com
Great stuff!!! Keep it coming... In a message dated 03/10/2000 8:10:41 PM Eastern Standard Time, daveb@eai.com writes:
Re: [motm] Router Weirdness
2000-03-11 by Paul Schreiber
12:0 (up) is ground. Install a jumper wire from the beveled lug (ground) to the top lug of the CV IN jack. I bet that does the trick! Paul S. ... From: Tkacs,
Router Weirdness
2000-03-11 by Tkacs, Ken
I have a question regarding my MOTM-700 Router s operation. The whole module seems to work. The strange thing about mine is that, with nothing plugged into
Re: [motm] VC Divider is...ALIVE!!
2000-03-11 by J. Larry Hendry
Cool !! LH ... analyzer. ... this ... be ... wire
Re: [motm] EMS Voc. ,Paul,-I have Moog 16Ch. schemos
2000-03-11 by william Hanson
... the Moog 16 Ch.unit If Yer interested let me know. Bill Hanson. Auf./Later-tweak on every one. __________________________________________________ Do You
MOTM-440...is ALIVE!!
2000-03-11 by Paul Schreiber
Batting 2 for 2 this weekend :) Waiting for a *certain bald person* to post demos. But the pcb is 100%! Yeah! Paul S. off to soccer
FW: [motm] Patch Diagramming Revisited
2000-03-11 by Tkacs, Ken
I did the switches with the idea that I would be writing on patch sheets by hand with a pen. Later, I could do them up nice in Visio for binding, but I
Re: [motm] EMS Vocoder
2000-03-11 by alt-mode
Careful, it looks like Robin Wood still sells them, according his web site: http://www.ems-synthi.demon.co.uk/ Of course, it is also alleged that he still
VC Divider is...ALIVE!!
2000-03-11 by Paul Schreiber
Attached are some of the VCPD outputs as shown on a HP1662C logic analyzer. The input clock is 5Khz (it will work up to 18Khz before funny stuff happens). As
EMS Vocoder
2000-03-11 by Paul Schreiber
Any have schematics? I have the sales literature. Paul S.
Re: [motm] Pulse Divider
2000-03-11 by jwbarlow@aol.com
... You can run audio in it? Seems like that same divide by this, and synch with that guy wanted to run audio into everything! I bet he s really looking
RE: [motm] A VCLFO Lives
2000-03-11 by jwbarlow@aol.com
... And get several of these outputs simultaneously, and they can be used to create complex rhythmic patterns (like those cute little humans often do) if you
Re: [motm] Patch Diagramming Revisited
2000-03-11 by alt-mode
Ken, This is great stuff! I see that I m going to need to get a copy of Visio for my home machine in order to take advantage of your handy work. Please keep
RE: [motm] Patch Diagramming Revisited
2000-03-10 by Dave Bradley
Here s an image of a patch I created in Visio. Once I got around some translation problems between Ken s and my versions of Visio, and once I had created some
Re: [motm] Pulse Divider again and again
2000-03-10 by Paul & Alleyne
hello, sorry i forgot the other serious point - paul, you might try www.drummachine.com they have a pretty interesting site (if you don t know it already), i m
Re: [motm] Pulse Divider again...
2000-03-10 by Paul & Alleyne
... hello again ( i really ought to think before i hit send) the question at the heart of this is what market (?!) do i want to hit with this module..? i d
Re: [motm] Pulse Divider
2000-03-10 by Paul & Alleyne
... um, the thing with our simmons though, is so much as look at it and it ll trigger itself. though being the broadminded liberal man of the world that i am,
Re: [motm] Pulse Divider
2000-03-10 by Paul Schreiber
The question is: do they have a minimum spec? I +5V enought to cause a trigger? I *really* don t want to have anything bit +5V outs. Paul S. ... From: Paul &
Re: [motm] Pulse Divider
2000-03-10 by Paul & Alleyne
... erm, delete that - i meant +12v too much king tubby... cheers paul b
Re: [motm] RE: Compact Phasor / MOTM phasor
2000-03-10 by Paul Schreiber
Sorry, I wasn t clear. There are NO other MOTM modules used. Just *new and never-before seen* features built into the phaser itself!! Hee Hee Hee Time to put
RE: [motm] RE: Compact Phasor / MOTM phasor
2000-03-10 by Brousseau, Paul E (Paul)
Well, I might be mistaken, but it sounds somewhat like there s a 120 in phaser_2.mp3. And perhaps in phaser_3.mp3, there s a 700 switching between two audio
Re: [motm] Pulse Divider
2000-03-10 by Paul & Alleyne
... hello all, well my sketchy knowledge of drum machines is as follows: Roland Dinsync runs a +5v pulse (ie you can build a din to jack cable and use the