Yahoo Groups archive
Messages
Page 35 of 56 · 2770 messages matched
2007-08-13 by robert piotrowicz
hallo is there any information when model 18 mixer will be realised and in which version I found myslef that whis module is most wanted on the marked of eurorack modules thanks for possibli reallisic answer with best robert www.musicagenera.net
2007-08-12 by Axel Jungkunst
Hi Peter, when will the Model 28 available again at AH? best regards Axel (i think you can figure that out) schrieb: > > All - > > Because I'm anal and have been around the block more times than I care > to say, I mailed a Model 25 to myself to see how the Ring Modulator's > cali
2007-08-12 by (i think you can figure that out)
All outstanding orders for the Model 28 have been shipped. AH will be placing another soon I imagine as it sold quite well. - P --- In PLAN_B_analog_blog@yahoogroups.com, Axel Jungkunst wrote: > > Hi Peter, > when will the Model 28 available again at AH? > best regards > Axel > >
2007-08-12 by (i think you can figure that out)
All - Because I'm anal and have been around the block more times than I care to say, I mailed a Model 25 to myself to see how the Ring Modulator's calibration held up in transit. I shipped it Fedex, knowing it would travel 'pert near across the U.S and back before it came back. L
2007-08-12 by (i think you can figure that out)
The Evil Twin is 14 HP wide, which is (not that it's important) my favorite module width. It great because I can space out the controls so everything's not so damned cramped. There will be instructions on how to retrofit the 15A to older M15's - you're all covered! It's really ea
2007-08-11 by gabu_004
WOW!!!c'est incroyable! 3 out of the 4 modules I've been waiting to come back instock :) but what about Mr. Heisenberg? Please, don't make him cry... ;P Questions now: 1) What is the HP width of the evil twin...since he's a twin that just turned out to be evil, could that mean it
2007-08-11 by (i think you can figure that out)
All - We'll be dropping off Poly EGs, Multimode Filters, Timbral Gates and Audio Processors to Analogue Haven early this afternoon. Those of you who've been waiting need not any longer. Well, a couple of hours. Next week a large lot of M15's, the balance of the M25 order and poss
2007-08-10 by (i think you can figure that out)
Later this evening I had a real nice conversation with Nyle Steiner, always a pleasure as he's a tremendous guy, and discussed the possibility of working on a project together. hmmmmmmmmm..it could be very interesting. More info will be posted when it's available. - P
2007-08-10 by (i think you can figure that out)
Got a surprise visit today from Chris Tillman of GNR at the shop, as they've returned from a (highly) successful first leg of the tour (Mexico, Australia, Japan). The official word is the Plan B system behaved exceptionally well under some pretty hairy conditions, up to and inclu
2007-08-09 by (i think you can figure that out)
All, I'd like to extend a big welcome to Samuel Michaels who's joining the corps on a part-time basis (Tuesday's and Thursday's) and will provide his talents for assembly to keep the machine rnning here. Sam worked for me at M&K and we're back at it now at Plan B. He's a good guy
2007-08-09 by gabu_004
Oups!!! My mistake, I didn't take a look at the image of the module for a while and indeed there's a stereo output...yay sorry! But the reason for the stereo in would be for treatment of processing only for external stereo signals or, for exemple to apply the effect at the end of
2007-08-09 by (i think you can figure that out)
...you're still bouncing back!
2007-08-08 by (i think you can figure that out)
I was thinking last night during my usual Tuesday night special Beef Veggie soup from Sitton's Diner in Noho - if the poll tells me I should advance with the Model 27 as a retrofitted Behringer, i might (possibly, as in 'may') release the bare PCB for that as a DIY product. All t
2007-08-08 by (i think you can figure that out)
Stereo ins, is the DD400 has it, I can do that. NOt sure, I didn't see the need for stereo inputs (you comments are welcomed). Stereo outputs however - yes and it's true stereo - the delay waffs across the stereo field in time with the tap frequency. Next week, hopefully his week
2007-08-08 by (i think you can figure that out)
...that was quick.
2007-08-08 by gabu_004
hehehe yeah behringer isn't all the best out there LOL But hey it,s cheap and you don't feel bad is a drunken punk drops his beer pitcher on the your Behringer mixer LOL!!! So tell me Peter, Have you thought of making the in and out with a stereo option? I mean there's a lack of
2007-08-08 by (i think you can figure that out)
... have no idea why, just called my ISP. Hopefully this is a temporary issue that won't go on much longer. The Buzzclick Music site is also down and I checked another site (miracle-software.com -- not mine) that I know is also on the server, and it's down as well. So it ain't me
2007-08-08 by Axel Jungkunst
Hi meic, you have to pay 8 Euro for an air mail envelope! all the best Axel (i think you can figure that out) schrieb: > > 30 Euro to mail a padded envelope? woah. > > All you have to do is pull the component, stick it in a small piece of > IC tubing (you can get this at any Elec
2007-08-08 by jalmari3
Thank you! --- In PLAN_B_analog_blog@yahoogroups.com, "(i think you can figure that out)" wrote: > > You will notice two trim pots on the M13 PCB. To make the inputs less > sensitive, just back those down. The upper trimmer is for the upper > gate, the lower trimmer is for the po
2007-08-08 by (i think you can figure that out)
What is with me and typing? Have you ever noticed I usually screwup the money words? All the and's, but's, if you's are OK, then I come to the part of the exact location of the problem and it's at the sispo sjsiu wwiwoim, and I send that without proofing. It's uncanny. Anyway, I
2007-08-08 by (i think you can figure that out)
You will notice two trim pots on the M13 PCB. To make the inputs less sensitive, just back those down. The upper trimmer is for the upper gate, the lower trimmer is for the power gate. As far the amp mode - this is a function of the beast. Some of what you're hearing is no filter
2007-08-08 by (i think you can figure that out)
I've uploaded a PDF which lists the way the SELECT input should work (and is working on all of the M28's in stock at our dealers and for 5 of the ints already purchased) and the incorrect way they were working on 15 of the units shipped. see "select_out_truth_table.pdf" in the FI
2007-08-08 by (i think you can figure that out)
30 Euro to mail a padded envelope? woah. All you have to do is pull the component, stick it in a small piece of IC tubing (you can get this at any Electronics store - they probably won' charge you for a lttle piece). Tape off the ends to it won't fall out, and then put that in a
2007-08-08 by jalmari3
I like M13 too. Although I wonder, why the VC inputs are so sensitive. I just tested Gate 1 of my unit: It tops at 4.3V. This often necessitates attenuation of the CV signal. (I would gladly change the offset controls to VC input attenuators.) Also, the amp only mode is much quie
2007-08-08 by meic1965
--- In PLAN_B_analog_blog@yahoogroups.com, "(i think you can figure that out)" wrote: > > All, > > We have discovered an error in the programming of the Model 28 Tapper. > There's a fix - please read on. > > There are two input pins on the microprocessor which determine which > o
2007-08-07 by cray5656
I must have missed this???? added by grenader: click on the POLLS tab
2007-08-07 by (i think you can figure that out)
You don't have to worry about that! I've already checked it out . All these Behringer pedals work on the same principle. Once you work out how to add VC, you can do it to all of them by just subbing one PCB for another - all the controls, etc are in the same location. They could
2007-08-07 by gabu_004
Yeah I have voted to do it! Seems a good alternative and I trust your judgment... But please, don't make plan B the Behringer of Modular synth...;P cheers g. --- In PLAN_B_analog_blog@yahoogroups.com, "(i think you can figure that out)" wrote: > > ALl, > > Please make usre you gi
2007-08-07 by (i think you can figure that out)
All, We have discovered an error in the programming of the Model 28 Tapper. There's a fix - please read on. There are two input pins on the microprocessor which determine which of the three SERIAL output states (quarter note/eight/triplet) are passed through. These are fed by two
2007-08-07 by (i think you can figure that out)
ALl, Please make usre you give us an idea of our proposed solution for the Model 27. Can't make a decision based on too few votes! thanks, - P ]
2007-08-06 by (i think you can figure that out)
Hey Phil - Your email host is returning my letters to you thinking they are spam.
2007-08-06 by (i think you can figure that out)
I've put a picture of the upcoming 15A VCO Expander in the Misc. folder of this blog. Have look...
2007-08-05 by jalmari3
Hooray for the M23! Interesting to see, how the "different" multiple will turn out, as multiples are kind of important. Doepfer is also planning a new switched multiple (A-182).
2007-08-04 by (i think you can figure that out)
hmmm...you learn something every day... I was fiddling around with the M25 in the studio here, the 'I wonder what would happen if I put this here' routine, when I tripped on to something interesting. Running the same signal through both sides of the Ring and flipping the FEEDBACK
2007-08-04 by PLAN_B_analog_blog@yahoogroups.com
Enter your vote today! A new poll has been created for the PLAN_B_analog_blog group: DECIDE THE FATE OF THE MODEL 27 DIGITAL DELAY: How would you feel if the Model 27 consisted of a Behringer DD-400 Digital Delay pedal board which had been stripped, mounted on a backplane and hea
2007-08-04 by (i think you can figure that out)
Oh crap - I forgot about this one. Yeah...the Model 27. There's a bit of an issue with that one, now is as good of a time to help me decide on it as any. I need you guys to give me input here. OK, here goes: The M27 was set to use the Coolaudio Delay chip set - their delay and th
2007-08-04 by michaeltritter
yo, what about the model 27 digital delay? don't sleep on that! mt --- In PLAN_B_analog_blog@yahoogroups.com, "(i think you can figure that out)" wrote: > > Now that the 25, 26 and 28 are out, I thought I'd take a moment to > outline and update the release schedule. > > 1) The 15
2007-08-03 by (i think you can figure that out)
Now that the 25, 26 and 28 are out, I thought I'd take a moment to outline and update the release schedule. 1) The 15A VCO Expander is next on the list. Faceplates are ghere, waiting to nail down one section of the circuit before PCB art is sent to fab. Their turnarond is quite q
2007-08-03 by Bryan E Cornell
I need to raise some cash and I'm selling a Plan B M12 rev. 2 State variable vactrol filter for $180 (buyer pays shpping). It's fairly new and has seen light use. I would prefer to ship in the US. Bryan
2007-08-03 by (i think you can figure that out)
The first lot of Model 25 Multi-Tasking Audio Processors will be at Analogue Haven tomorrow.
2007-08-02 by David Salter
That's great - made me laugh as well as learn something David Salter Senior Consultant PSG Reuters Messaging: david.salter.reuters.com@reuters.net (t) +44 (0)20 7542 2402 | (m) 07990562402 | (f) 52699 Get the latest news at Reuters.com -----Original Message----- From: PLAN_B_anal
2007-08-01 by (i think you can figure that out)
Made one. It's sucky, but I think it'll give you the idea of what involved, required and what can be expected: http://www.youtube.com/watch?v=aT37YbHv3so
2007-07-31 by (i think you can figure that out)
Norman Fay said: > You should have also made your end-users aware of this issue as soon > as it happened via this mail list. Look at the way Paul Schreiber > does this on the MOTM list, and emulate that. Being proactive always > beats being reactive. It's easier, it takes less ti
2007-07-31 by NoRMaN PHaY
--- In PLAN_B_analog_blog@yahoogroups.com, "(i think you can figure that out)" wrote: > > All of our dealers who had open orders were made aware of what happened -- as soon as it happened, including Andreas. > > - P > You should have also made your end-users aware of this issue a
2007-07-30 by fizzydiodes
sorry to hear about the problems peter.I know the ins and outs of small business , cash flow and also staff issues and had all these.The only way we survive is via having our own online shop.We sell through dealers and we sell via paypal on an online shop also.We make 30% more vi
2007-07-30 by Axel Jungkunst
Peter, I apologize the circumstances, but why don't you tell us those things within this mailing list. So all the people including your dealers will know about your particular circumstances and they will wait until better times. I know that some guys including mine are waiting fo
2007-07-30 by (i think you can figure that out)
All of our dealers who had open orders were made aware of what happened -- as soon as it happened, including Andreas. - P --- In PLAN_B_analog_blog@yahoogroups.com, Axel Jungkunst wrote: > > > > > > Peter, > I apologize the circumstances, but why don't you tell us those things >
2007-07-30 by (i think you can figure that out)
Thanks for this. It's appreciated. We're shipping now, just not at the clip we used to be. AH has stock of 28's 15's, 17, and we've delivered 12's, 13's, and 10's since as well. When all this happened, I had geared up for the fist release of the Model 28's. This means acquiring t
2007-07-30 by Doug Wellington
Peter wrote: > I thank you all for being patient with us. We're working hard to get back to where we were. Good luck with that! I for one am looking forward to buying more modules from you... Doug http://www.analognotes.com
2007-07-30 by (i think you can figure that out)
Axel, First, please leave political comments to a forum which welcomes them. This one isn't it. Secondly, what's happened is sad. I completely agree. In June, my production staff (1 guy) left the company without giving notice. As you can imagine this screwed things up. Since then