Re: [Simmons Drums] Re: Digest Number 956
2007-09-28 by Jack
le 28/09/07 3:01, Jim à jbospunk@yahoo.com a écrit : Or you could always break down and buy a brand new set of Roland V- Drums!!!!!!! ha ha If it sounded
Messages
Browse messages
Page 111 of 172 · 8595 messages matched
Re: [Simmons Drums] one more thing ...
2007-09-28 by Jack
le 28/09/07 2:06, michael.buchner@debitel.net à michael.buchner@debitel.net ... one more thing ; we have to find the way to devellop its trigging dynamic,
Re: Digest Number 956
2007-09-28 by Jim
Or you could always break down and buy a brand new set of Roland V- Drums!!!!!!! ha ha ... DIY ... address ... all in ... AKAI ... ... sound... ... the ... you
Re: [Simmons Drums] Digest Number 956
2007-09-28 by Jack
le 28/09/07 2:19, michael.buchner@debitel.net à michael.buchner@debitel.net a écrit : You have bad ZI pads? May be it would help you if I send you the DIY
Re: [Simmons Drums] SDS3/4 clone-Design rights?
2007-09-28 by Jack
le 28/09/07 2:06, michael.buchner@debitel.net à michael.buchner@debitel.net ... It s all for sure some very precious & hard work thanks for doing it
Re: [Simmons Drums] Digest Number 956
2007-09-28 by michael.buchner@debitel.net
You have bad ZI pads? May be it would help you if I send you the DIY instruction. It is easy to repair them. Send me your private email address and on we go.
Re: Re: [Simmons Drums] SDS3/4 clone-Design rights?
2007-09-28 by michael.buchner@debitel.net
I think, it is not necessary to clone the whole SDX. The whole sampling and sound stuff with the nine sounds per pad, the sampling itself, the storage a.s.o.
Re: Betr: Re: [Simmons Drums] SDS3/4 clone-Design rights?
2007-09-27 by Jack
... I don t see who you mean :-) ... kind a MAc I supose ... ; -) some converting ... just that ? ;-))) ... as you say ... ... Well of course, & they also used
Betr: Re: [Simmons Drums] SDS9 start up problems
2007-09-27 by trevor_berner
... Thanks Steve, the PSU produced the voltages you stated and I checked with and without the main PCB connected so as to rule out a faulty componenet pulling
Re: [Simmons Drums] SDSV Crosstalk
2007-09-27 by Jack
le 17/09/07 18:27, Jimmy Earnshaw à jbospunk@yahoo.com a écrit : Thanks so much Michael, I will give it a try. Or, better yet, attempt to find some original
Re: [Simmons Drums] Bob Henrit and Simmons
2007-09-27 by Jack
le 13/09/07 11:52, jesper@electronic-obsession.se à jesper@electronic-obsession.se a écrit : Hi list! I finally am a happy owner of the Complete Simmons
Re: [Simmons Drums] SDX
2007-09-27 by Jack
le 6/09/07 15:01, mcsorley_jon à mcsorley_jon@yahoo.com a écrit : I also remember hearing that Akai were involved, so I was wondering if SDX technology was
Re: [Simmons Drums] SDX
2007-09-27 by Jack
le 6/09/07 15:01, mcsorley_jon à mcsorley_jon@yahoo.com a écrit : Hello everyone, Just a quick question to anyone who has time to answer - does anybody know
RE: Betr: Re: [Simmons Drums] SDS9 start up problems
2007-09-27 by Steve Ridley
... Do you have schematics? If none are available online, I think I have some, but they may take afew days to find. BTW, the PSU should give +5v, +15v and
Re: [Simmons Drums] Digest Number 956
2007-09-27 by Jack
le 26/07/07 3:28, michael.buchner@debitel.net à michael.buchner@debitel.net ... , Hi Michael how much for some repairerd ZI pads ? How many ? bye, PAtrice.
Re: Betr: Re: Re: [Simmons Drums] Re: SDS3/4 clone-Design rights?
2007-09-27 by WT
Go figure.....then I do exactly the same !! lol WT http://medlem.spray.se/waveterm/LJLab2006/ [Non-text portions of this message have been removed]
Re: Betr: Re: Re: [Simmons Drums] Re: SDS3/4 clone-Design rights?
2007-09-27 by Jack
... Hi again, sorry I m just discovering messages one after ones ... Well about the SDX, if someone is definitely thinking seriously to clone it , I ll have
Betr: Re: [Simmons Drums] SDS3/4 clone-Design rights?
2007-09-27 by Berk Aarts
I recall there is a guy in France who owns the schematics for the SDX? hihi sorry Patrice What I recall from memory is that the SDX is not to hard to clone it
Re: [Simmons Drums] Introducing
2007-09-27 by Jack
... HI Benjamin , Welcome ! It s good to have one more French here , we re not really concerned by Simmons in France are we ? bye, PAtrice.
Re: [Simmons Drums] Question from a Rush fan....
2007-09-27 by Jacquot.Patrice@free.fr
Hi Roger , I ve been a Rush fan too , especially for the electronic drum sounds !!! Lance as described nicely what I ve been reading here or there ... I m
Re: [Simmons Drums] quite funny coincident
2007-09-27 by Jacquot.Patrice@free.fr
Excellent !!! Patrice.
Re: [Simmons Drums] SDS3/4 clone-Design rights?
2007-09-27 by Jacquot.Patrice@free.fr
Hi guys, I had been out of connection for a loooong time... About the permission to clone , I think there s only one guy that we all know that could say more
Re: [Simmons Drums] SDS9 start up problems
2007-09-27 by trevor_berner
... Thanks Jesper, as posted back to Berk Aarts: Yeah I know sounds kinda wierd but had to start somewhere and replacing the battery at least gave me static
Betr: Re: [Simmons Drums] SDS9 start up problems
2007-09-27 by trevor_berner
... wrote: Yeah I know sounds kinda wierd but had to start somewhere and replacing the battery at least gave me static memory again, have removed the voice
Betr: Re: [Simmons Drums] SDS9 start up problems
2007-09-27 by Berk Aarts
Changing the battery after 10 years in a box?? there s nothing to remember after that period off time. besides if you changed it by just removing it and then
Re: [Simmons Drums] SDS9 start up problems
2007-09-27 by jesper@electronic-obsession.se
Keep us posted and we might sort it out together... electronically yours, jesper
Re: [Simmons Drums] SDS9 start up problems
2007-09-27 by trevor_berner
... Thanks Steve, I will perhaps remove the voice eproms to see if this is the case. Regards, Trevor
Re: [Simmons Drums] SDS9 start up problems
2007-09-27 by trevor_berner
Thanks for the advice Jesper I will check out the voltage via the PSU. Regards, Trevor ... manual? ... what ... which ... retirement ... and ... seems ...
Re: [Simmons Drums] SDS9 start up problems
2007-09-27 by jesper@electronic-obsession.se
Sounds like the 6 indicates a malfunction. Have you checked a manual? Otherwise, the first thing to do is to see if the PSU is delivering what it s
RE: [Simmons Drums] SDS9 start up problems
2007-09-26 by Steve Ridley
... I had a similar problem with an SDS1000 (similar circuit). One of the voices was faulty, and once the processor had done it s start up proceedure, the
SDS9 start up problems
2007-09-26 by trevor_berner
Hi all, my first post to this user group, I have an SDS9 module which has been with me since new but only recently brought out of retirement after about 10
Re: [Simmons Drums] quite funny coincident
2007-09-26 by michael.buchner@debitel.net
Hey, great! B.t.w.: Does anybody know where to get a good wlan cable from? ;-) [Non-text portions of this message have been removed]
quite funny coincident
2007-09-26 by jesper@electronic-obsession.se
I googled Simmonspictures and this is one of those showing up early; http://www.freepatentsonline.com/6649649-0-display.jpg electronically yours, jesper - --
Re: [Simmons Drums] SDS-400 Knob caps
2007-09-26 by jesper@electronic-obsession.se
if they re the same as SDS-8 and similar I dare say that you need the Cliff K85 (that s the knob name), as sold by Cliff Electronics in the UK. I think Maplin
Re: [Simmons Drums] SDSV Crosstalk
2007-09-26 by clae13
Or if you wanted to do it non-destructively, make up a short female-to-male adapter with the resistor wired into that. ... between live and neutral in the SDSV
SDS-400 Knob caps
2007-09-25 by plus_321
Slim chance, I know, but I m trying to track down some of the colored knob caps for my SDS-400. I need: 2 Blue and 2 Gray and 5 more of the same color (Any
Re: [Simmons Drums] sds-3/4 service and owners manuals??
2007-09-23 by randaleem
Hi Jesper, How about asking if he has an SDS3 and/or SDS4 manual and service manual? We ve got schematics and service notes for these; but no complete manuals
Re: [Simmons Drums] new chance at the drum book
2007-09-23 by thomas heckmann
If someone is really desperate to get one and has something worth trading, I have three of them and would let one go ! Best tph On 23 Sep 2007, at 09:59,
new chance at the drum book
2007-09-23 by jesper@electronic-obsession.se
http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=230174384653 electronically yours, jesper - -- --- ---- ----- ---- --- -- - www.electronic-obsession.se
Re: [Simmons Drums] SDSV cymbal pad
2007-09-22 by michael.buchner@debitel.net
I still have 2 of these, but I don t play them. In the early days they were wired for use with SDSV, very interesting: They contained 2 diodes, a small
Re: [Simmons Drums] Re: SDSV cymbal pad
2007-09-22 by jesper@electronic-obsession.se
Damn, those are ugly... sorry, but I can t help thinking that. But I guess Simmons got what they wanted, still now, 25 years later people recognize those
Re: [Simmons Drums] SDSV cymbal pad
2007-09-22 by jesper@electronic-obsession.se
I think Wolfgang does, he own just about every piece of Simmons model ever made... :) There were even some for sale here a few years ago if I m not making
Re: [Simmons Drums] SDS9 for repai
2007-09-22 by jesper@electronic-obsession.se
Don t count on me, I m just a rookie when it comes to electronics. I have my broken Odyssey and a friends SH-2 standing here staring at me with a sullen face
Re: SDSV cymbal pad
2007-09-22 by superwolle70
Here you are: http://www.simmonsmuseum.com/?area=pads&view=gallery&id=1&pic=28
SDSV cymbal pad
2007-09-21 by Jim
Just watched the video for Politics of Dancing by Reflex on you tube and spotted the elusive simmons cymbal pad. Great shot of the SDSV kit. I forgot how
SDS9 for repai
2007-09-21 by Jim
Wondering if anyone (Jesper) would be able to give me a hand in repairing my SDS9 module. It works, for the most part, save for the hi tom channel, which will
Re: [Simmons Drums] sds-2, pics and sounds
2007-09-21 by jesper@electronic-obsession.se
More or less all of them are 85-87 except on the PSU board where there are 79-circuitry. electronically yours, jesper - -- --- ---- ----- ---- --- -- -
Re: [Simmons Drums] sds-2, pics and sounds
2007-09-21 by Steve Ridley
... Have you looked at the bottom side of the voice boards? It s common to etch a make or model number along with the copper tracks. Also, if you cad take a
Re: [Simmons Drums] Re: sds-2, pics and sounds
2007-09-21 by jesper@electronic-obsession.se
Sure, if the SDS-2 would be considered a rarity then it would be worth copying, but I doubt it was. People sold off SDS-V s and the likes at the time. But keep
Re: sds-2, pics and sounds
2007-09-21 by superwolle70
Why would somebody copy a Picasso after the camera has already be invented? ... later ... sure looks ... described ... would ve ... much in ... Dave. It ...