Re: [ModularSynthPanels] CGS Synthacon VCF Stooge panel
2004-03-11 by ixqy@aol.com
In a message dated 3/10/04 8:21:04 PM Central Standard Time, pugix@ntelos.net ... Oops! Sorry, I was half asleep and going from memory (a scary thought!) when
Messages
Browse messages
Page 60 of 66 · 3299 messages matched
Re: [ModularSynthPanels] CGS Synthacon VCF Stooge panel
2004-03-11 by ixqy@aol.com
Hi, Thanks to Richard and John (and Larry!) for the helpful replies. I wasn t too sure what circuit was being mention for the All Pass input, but after
Re: [ModularSynthPanels] CGS Synthacon VCF Stooge panel
2004-03-11 by Richard Brewster
LOL! Nope. It looked nice before I sent it :).
Re: [ModularSynthPanels] CGS Synthacon VCF Stooge panel
2004-03-11 by Richard Brewster
Andrew, you meant a second 220K resistor, not 220 ohm. I m about to build my dual Synthacon VCF (two in 2U), and I ll be trying these CV resistors values,
RE: [ModularSynthPanels] CGS Synthacon VCF Stooge panel
2004-03-10 by John Loffink
1. Yes, just scale the input resistor, but don t expect steady tracking. This filter is all over the place in pitch when it self oscillates. 2. Yes. 3. No,
CGS Synthacon VCF Stooge panel
2004-03-10 by synthasaurus
Hi all, I was thinking of have a 2U Stooge panel made for the CGS Synthacon filter. I uploaded a tentative layout (a .jpg) in the files section of this list s
PSIM-1 Stooge panels
2004-03-08 by Larry Hendry
... OK, I know some of you are ordering PSIM-1 modules without front ... these. It is our intention to provide the panel with the DB-9 connector cut out
upload: design for dual CGS Cynare
2004-03-06 by Jeffrey Pontius
Because I have 1 of 2 of Ken Stone s CGS Cynare pcb s working and mounted onto a front panel, I thought I would post a Schaeffer 2U motm size front panel
New file uploaded to ModularSynthPanels
2004-02-21 by ModularSynthPanels@yahoogroups.com
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the ModularSynthPanels group. File :
New file uploaded to ModularSynthPanels
2004-02-21 by ModularSynthPanels@yahoogroups.com
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the ModularSynthPanels group. File :
Miniwave Expander Is Back
2004-02-08 by Dave Hylander
Hi everyone, I have the Miniwave Expander PCBs back in stock with a few changes. For those who don t know, this add on PCB for the Wiard/Blacet Miniwave adds
Stooge panels
2004-02-06 by Larry Hendry
To those that might be interested: OK, I think I have my act together enough to start taking your orders for panels. If you have any new designs you want,
Re: [ModularSynthPanels] Digest Number 131
2004-02-05 by Dana Fiorucci
on 2/4/04 11:43 PM, ModularSynthPanels@yahoogroups.com at ... M7 is the diameter in mm to obtain inches multiply by .03937 7* .03937 = .27559 so a .282 hole
Re: [ModularSynthPanels] Hole width for .25 pots?
2004-02-05 by Brice D. Hornback
M7 is the diameter. It s metric. M7 = .2755 OBVIOUSLY... I d add some extra wiggle room . the .282 diameter hole should work fine. Here s where I found
Re: [ModularSynthPanels] Hole width for .25 pots?
2004-02-05 by Jeffrey Pontius
... There are several panel designs in the Cat Girl folder that have pot holes for Alpha pots (as I m trying to use mine up). For example, check the file in
Hole width for .25 pots?
2004-02-04 by c45a6
Hello! I am working on a panel that will have a few Alpha potentiometers involved. (mouser part #31JN405) The specification sheet shows that the diameter of
Pane labels
2004-02-03 by karlllander
Hi All, It s great to see the effort you all put into making sure that your panels look fantastic. I have,(hopefully), a simple question. Is there a product
New/PCB Mounting
2004-02-01 by Krimo
Hi All, New to this group, live in Holland and working on MOTM/Oakley/CGS system. Got a CGS Steiner VCF PCB coming my way and got two questions (cross posting
Re: [ModularSynthPanels] New file uploaded to ModularSynthPanels
2004-02-01 by dave wright
scott/richard/group: i just put an mouser order in for some switchcraft jacks and the needed pots for the sawtooth animator so it will be prob be a week till
Re: [ModularSynthPanels] New file uploaded to ModularSynthPanels
2004-01-31 by Richard Brewster
I got around to taking some pictures today of one of my recent projects: 2 Oakley Little LFOs and 2 Oakley Little EGs in one 2U panel. There are two pictures
Re: [ModularSynthPanels] New file uploaded to ModularSynthPanels
2004-01-31 by Richard Brewster
The main idea of waveform animation is to impart dynamism to the sound that is independent of pitch. The MPWA accomplishes this by sawtooth phase shifting,
Re: [ModularSynthPanels] New file uploaded to ModularSynthPanels
2004-01-31 by Scott Juskiw
Sounds fabulous Richard, can you explain the patch? Is it just a saw into MPWA?
New file uploaded to ModularSynthPanels
2004-01-31 by ModularSynthPanels@yahoogroups.com
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the ModularSynthPanels group. File :
New file uploaded to ModularSynthPanels
2004-01-31 by ModularSynthPanels@yahoogroups.com
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the ModularSynthPanels group. File :
Re: [ModularSynthPanels] New file uploaded to ModularSynthPanels
2004-01-31 by Scott Deyo
and if you want to hear some very cool modular synthesis, circuit-bent sounds and great spastic beats check out mr. wright s new CD _Carrion Sounds_ at
Re: [ModularSynthPanels] New file uploaded to ModularSynthPanels
2004-01-31 by dave wright
hey everyone i actually just returned from a long vacation ( www.notbreathing.com/hawaii2.htm) to find my panel and module waiting for me. have not started
Re: [ModularSynthPanels] New file uploaded to ModularSynthPanels
2004-01-31 by Richard Brewster
I will reply later in detail about the MPWA. Give me a chance to make an MP3 from a recording of my ancient synth. -Richard Brewster
Re: [ModularSynthPanels] New file uploaded to ModularSynthPanels
2004-01-31 by Larry Hendry
... Tell us what attracts you to this module. ... I have done only one (quad low pass gate). The PCB fit quite nicely on one of my 3 pot long brackets. I ran
Re: [ModularSynthPanels] New file uploaded to ModularSynthPanels
2004-01-31 by Richard Brewster
I ve been looking pretty hard at the Cynthia Sawtooth Animator myself. I actually built one of the original Electronotes Multiphase Waveform Animators for my
New file uploaded to ModularSynthPanels
2004-01-31 by ModularSynthPanels@yahoogroups.com
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the ModularSynthPanels group. File :
New file uploaded to ModularSynthPanels
2004-01-31 by ModularSynthPanels@yahoogroups.com
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the ModularSynthPanels group. File : /Cat
New file uploaded to ModularSynthPanels
2004-01-31 by ModularSynthPanels@yahoogroups.com
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the ModularSynthPanels group. File : /Cat
New file uploaded to ModularSynthPanels
2004-01-31 by ModularSynthPanels@yahoogroups.com
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the ModularSynthPanels group. File : /Cat
Re: Steiner VCF
2004-01-31 by Richard Brewster
I like doing stereo modules for several reasons. I like to have two each of most modules because it makes stereo patches possible. If I am doing the panel,
Re: [ModularSynthPanels] upload: CGS vco 3U semi-motm Schaeffer design
2004-01-17 by Jeffrey Pontius
... I have used the motm lin/dc and FM2 periodically, so I thought I would continue some experimentation with the cgs vco. Maybe the reversible cv2 would have
Re: [ModularSynthPanels] upload: CGS vco 3U semi-motm Schaeffer design
2004-01-17 by Richard Brewster
Very nice panel. Not sure how often I would use both the AC and DC linear inputs at once. I might swap the DC linear FM input for a second reversible CV
New file uploaded to ModularSynthPanels
2004-01-17 by ModularSynthPanels@yahoogroups.com
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the ModularSynthPanels group. File : /Cat
upload: CGS vco 3U semi-motm Schaeffer design
2004-01-16 by Jeffrey Pontius
Hi synth panelers, I ve been working through my backlog of cgs modules. My recent completion (with a lot of great assistance from Ken Stone) is the cgs vco.
uploaded: CGS seq. switch - 2U motm style
2004-01-14 by Jeffrey Pontius
Hi all, I uploaded a 2U Schaeffer motm style panel design for Ken Stone s very useful sequential switch. The design has all of the inputs, outputs, LED s,
Re: [ModularSynthPanels] Moog MF-102 Stooge Panel Idea pt.2
2004-01-07 by Larry Hendry
I kind of like it too. We have one other Mooh Panel, the MF-101. However, it was made to look more MOTM like. Certainly there are some challenges with
Moog MF-102 Stooge Panel Idea pt.2
2004-01-07 by Michael
For the sake of symmetry I like this a bit better... http://www.pressurepenetration.com/panels/moog_mf102-2.jpg - Michael nil-x
Moog MF-102 Stooge Panel Idea
2004-01-07 by Michael
Hello, I wanted to see what people thought... It s a mix of the original Moog design with some MOTM style. Using the original spacing also means that the PCB
howard, can you upload your dual 8-in mixer design?
2004-01-05 by tsomneevich
Hi Howard, Would you mind uploading your design for your dual 8-in mixer on your site? I d like to adapt that for the CGS VCO so it s not humongous. Thanks,
New upload: Buchla 291 filter + Schaeffer design
2004-01-04 by Jeffrey Pontius
Hi all, I ve uploaded a Schaeffer front panel design for the rendition of the Buchla 291 filter that Scott Stites and I have been working on for the past 6
Re: [ModularSynthPanels] New file uploaded to ModularSynthPanels
2004-01-03 by Richard Brewster
I finally finished building the combination dual Little LFO, dual Little EG module. It came out quite well. I plan to take photos and post them. The most
New file uploaded to ModularSynthPanels
2004-01-03 by ModularSynthPanels@yahoogroups.com
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the ModularSynthPanels group. File :
New file uploaded to ModularSynthPanels
2003-12-29 by ModularSynthPanels@yahoogroups.com
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the ModularSynthPanels group. File :
New file uploaded to ModularSynthPanels
2003-12-29 by ModularSynthPanels@yahoogroups.com
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the ModularSynthPanels group. File :
New designs uploaded
2003-12-17 by davebr@earthlink.net
I ve been uploading some of my latest designs to my folder (DJB). These include: three input mixer / spring reverb / 440Hz Std / output gain dual trigger delay
Re: [ModularSynthPanels] New file uploaded to ModularSynthPanels
2003-12-16 by Richard Brewster
I have been looking over Ken Stone s neat version of Electronotes VCO Option #1. I was thinking how it could be put behind a MOTM style panel. As Ken s note