RE: [vintagesynthrepair] Re: Yamaha TG33 power supply
2010-02-25 by Brian
Hi Royce No problem. I have access to the entire Yamaha on-line database, plus I carry a 3 CD set of schematics. I am a professional engineer repairing, to
Messages
Browse messages
Page 59 of 155 · 7723 messages matched
Re: Yamaha TG33 power supply
2010-02-25 by Royce
Thanks Brian. What a great scan. I wish I could get my ccts to scan that well. Looks like there is a 5V reg for the digital and the full voltage is sent to
Yamaha TG33 power supply
2010-02-24 by Brian
I can offer you a copy of the whole cct, however you should be OK with 12V but you may want to check the operating temperatures of the regulator ccts. If the
Yamaha TG33 power supply
2010-02-24 by Royce
Hi I am looking for a circuit diagram for a TG33. I want to see if I can use a 12 power supply to drive it. The one that came with it is a Yamaha PC-3 10 volts
RE: [vintagesynthrepair] Kurzweil SP88x
2010-02-22 by Brian
Usually there area couple of screws at the side front that need to be removed before the top will open. You may find a row across the front as well. Regards
Kurzweil SP88x
2010-02-22 by n8398r
I am trying to open the case on this unit. I have taken out all the screws on the back and on the bottom of the case towards the back. There is some play in
Re: [vintagesynthrepair] Mini-Moog Keyboard Question
2010-02-20 by Miguel Mendoza
I second this. Did you try the CV inputs? If the CV changes the pitch it has to be something about the keyboard connector. From: John Henson Sent: Saturday,
Re: [vintagesynthrepair] Mini-Moog Keyboard Question
2010-02-20 by John Henson
Hi Sam, I would recommend a look at the 6 pin keyboard interface connector that lurks under the modulation pitch bend section. The silver plating on these
Re: [vintagesynthrepair] Mini-Moog Keyboard Question
2010-02-20 by Neil Boughey
I m no great expert on electronics, but i understand minimoogs, particularly early to mid manufacturing period, suffer from oxidation and corrosion to the
RE: [vintagesynthrepair] Mini-Moog Keyboard Question
2010-02-20 by Samuel Adams
IF power supply died, why does everything except the keyboard function properly? ... From: vintagesynthrepair@yahoogroups.com
RE: [vintagesynthrepair] Mini-Moog Keyboard Question
2010-02-20 by Brian
It sounds as though the power supply has died! Regards Brian G3OYU From: vintagesynthrepair@yahoogroups.com [mailto:vintagesynthrepair@yahoogroups.com] On
Mini-Moog Keyboard Question
2010-02-20 by Samuel Adams
Hi, I m a new member to this group and am in need of assistance. I have a 1973 Mini-Moog that I put in storage about 10 years ago in my attic in the original
Re: [vintagesynthrepair] Looking for Moog Source PSU/information
2010-02-19 by Paul Cunningham
hey there... i ve just had mine opened up and took a few photos of the psu. nothing too detailed, but i uploaded the photos to the photos section of this
Looking for Moog Source PSU/information
2010-02-18 by mkliimask
Hi, I recently acquired the reminders of a Moog Source without power supply. I plan to resurrect the poor synth, and having examined the schematics the +-15V
Peavey DPM with output prob
2010-02-16 by brofjw
Hi everyone. I have a Peavey DPM2 synth which I just got on Ebay. It s the second Peavey synth I ve owned. I know Peavey synths are looked at tongue-in-cheek
Re: problem with JUNO 106
2010-02-14 by alexandrodeexu
Hi,it s impossible to make uncorrect power conection, caus 4 pin don t allows uncorrect position all 3 pots make voltage change on it s output from 0 to +5V
Re: [vintagesynthrepair] problem with JUNO 106
2010-02-12 by Malte Rogacki
Hi, please verify you get the correct power to the bender board. It s the jack with the four contacts. Have you by chance swapped the connectors?
Re: [vintagesynthrepair] problem with JUNO 106
2010-02-12 by boris dumery
Hi dear, Maybe ask help to : ulfihavesynth.com. I assume he is also on FaceBOOk Bo ... From: alexandrodeexu Subject:
Re: Sequential Pro One knobs
2010-02-12 by duncan
there s a vendor on ebay who sells an aluminium sequential-like knob in at least two sizes. I m putting these on my pro-1 when I rebuild the thing, rather than
Re: [vintagesynthrepair] Sequential Pro One knobs
2010-02-11 by Mike de Vries
Ebay s Chipsforbrains often sells them, or P5 parts. http://shop.ebay.com.au/chipforbrains/m.html?_nkw=&_armrs=1&_from=&_ipg=&_trksid=p3686 Ask em if
Sequential Pro One knobs
2010-02-11 by GB
Does anyone know of another source for Pro One knobs? $9 each (for two, incl shipping) seems a bit steep @ Winecountry. PS. If anyone needs a replacement
RE: [vintagesynthrepair] E510
2010-02-11 by Brian
Many thanks for that Alex. Regards Brian G3OYU From: vintagesynthrepair@yahoogroups.com [mailto:vintagesynthrepair@yahoogroups.com] On Behalf Of Alexis V.
E510
2010-02-10 by Alexis V. Rogers
Not sure about a UK source but here s one in Germany: http://www.cedos.com/e510_midi_chip.htm Cheers, Alex
E510
2010-02-10 by Brian
Hi All I have an Orla C7600 in for repair and need an E510 IC for the keyboard scanning PCB. Any ideas where to get one, preferably in the UK although willing
Re: [vintagesynthrepair] SH5 vcf pot .
2010-02-10 by michael moller
Hey . Am looking to replace the cut off and resonance pots on my SH5 . Can you advise me ? Thanks . Mike .
problem with JUNO 106
2010-02-09 by alexandrodeexu
Hi I ve replaced Bender Board in my synth to brand new ( http://www.technologytransplant.biz/product_info.php?cPath=30_29_21&products_id=244 ), caus there was
Re: Alps switches
2010-01-31 by jfloydhumanoid
Thanks for the help, folks! I ll order a few different switches & see if anything will serve as a replacement.
Re: [vintagesynthrepair] Re: Alps switches
2010-01-28 by GB
... If you can find something that fit the bottom, you can probably craft the plunger part out of plastic standoffs or similar.
Re: Alps switches
2010-01-28 by Scott
... http://www.mouser.com/ALPS/Electromechanical/Switches/Tactile-Jog-Switches/_/N-5g2mZ1z13wb5?P=1z0z63vZ1z0z54oZ1z0z7zaZ1z0z5h6Z1yzxlxkZ1z0z2mb or Check this
RE: [vintagesynthrepair] Alps switches
2010-01-28 by Sven Braamkolk
Look for tactswitch on the internet. If you can take the top off there ll be a lot of replacements. greetings sven To: vintagesynthrepair@yahoogroups.com From:
Alps switches
2010-01-28 by jfloydhumanoid
Hi, all, Does anyone know where I can find 5 or 6 of these? alps_switch They measure appx
roland mc-505 part faders
2010-01-26 by rokomoteebu
i need to replace part faders on roland mc-505. i ve figured out that they are 10kohm, but i didn t find faders that are exactly the same in a matter of pins..
Re: [vintagesynthrepair] Resistor trim pots for Micromoog (need to find replacements)
2010-01-18 by John Karns
... Digikey is one place to look. Jameco is not so much oriented toward components as Digikey, but AFAIK, they do deal in them to some extent. -- John Karns
Korg X2
2010-01-18 by tim slim
Hi guys I am looking for a floppy drive unit for my Korg X2. Thanks Tim __________________________________________________________________ The new Internet
Korg MS-20 Filter Surprise
2010-01-18 by pikil@ameritech.net
I recently opened up my MS-20 to fix some key contacts and clean up some pots. My unit HAS THE SCREW in front, but to my surprise I found the Korg 35 filter
RE: [vintagesynthrepair] Re: Resistor trim pots for Micromoog (need to find replacements)
2010-01-18 by Brian
No! The ones in the Minimoog are similar to this one: http://uk.rs-online.com/web/search/searchBrowseAction.html?method=getProduct
Re: Resistor trim pots for Micromoog (need to find replacements)
2010-01-18 by martinreuter
Hi Allan, did you already asked Mike Bucky from Modusonics? Here´s the mailadress: mbucki@pair.com This guy is sitting on the old Moog stuff, he bought all
Re: Resistor trim pots for Micromoog (need to find replacements)
2010-01-18 by Scott
... Not just mouser.com but www.newark.com www.digikey.com www.futurlec.com www.alliedelec.com
Re: Resistor trim pots for Micromoog (need to find replacements)
2010-01-18 by mlcsixand78s
Thanks for replies! The closest examples I can find are: Mouser
RE: [vintagesynthrepair] Resistor trim pots for Micromoog (need to find replacements)
2010-01-18 by Brian
Hi Allan If these are similar to those used in the Minimoog then you can find replacements within the RS Components catalogue. Regards Brian G3OYU From:
Re: [vintagesynthrepair] Resistor trim pots for Micromoog (need to find replacements)
2010-01-18 by Paulo Palmieri
Try www.mouser.com There you will find the datasheets and exactly matches for your searches. Ebay is a good source too. Good luck, Paulo ... From: mlcsixand78s
Resistor trim pots for Micromoog (need to find replacements)
2010-01-18 by mlcsixand78s
Hello, I hope someone can help. I m in search of new replacement RESISTOR TRIM POTS for my Micromoog. (example 1K, 10K, 100K, etc). I have had problems tuning
VERMONA SK86
2010-01-16 by gatmezeiz@t-email.hu
Dear All, I have a Vermona SK86. The first digital piano(?). The problem is that everithing works on in, except the voice. There is no any sound coming from
Crumar T1/C no sound in the treble section
2010-01-15 by Mark
I recently picked up this baby at a local Salvation Army for 15 bucks! The thing is in terrible shape with a missing cheek but that didn t stop me at the time.
RE: [vintagesynthrepair] Korg MS-20 stuck knob fixed!
2010-01-13 by Brian
Hi Guys Given that Deoxit has lubricant suspended in the cleaning solution it should not be necessary to grease the pot shaft. Servisol Contact Cleaner, for
Re: Changing battery in original Wavestation
2010-01-13 by kindabizzy2
... I replaced the battery in my WS A/D a couple of years ago. It was just a matter of opening the case, finding the battery - which was in mounted in a
Korg MS-20 stuck knob fixed!
2010-01-12 by mrbfrankus
Hello, I joined this group to find a fix for a stuck knob on my MS-20. Well I went a head and fixed it before getting approved so I thought I d share my
Changing battery in original Wavestation
2010-01-04 by brofjw
Hi, folks. I don t post here often, I just read sometimes. But now I have an original Wavestation that needs the battery replaced. I actually have the new
Re: Roland D70
2009-12-30 by langercs
Hello! Send me an email. I can send you a D70 service manual! Best regards
Re: TECHNICS AX-7 - help needed
2009-12-17 by Noel Buhagiar
If I remeber correctly, the same sound came out of headphone o/p; (bassy reverberating wave sound continuously heard). But will check this again. Many thanks