Re: Omni 2 readable service manual?
2013-02-01 by The Wizard
Yes, Jim, I have an original OMNI-2 service manual. How can I be of assistance? ... kevin@soundmindbodystudio.com
Messages
Browse messages
Page 26 of 155 · 7723 messages matched
Omni 2 readable service manual?
2013-02-01 by Jim Blair
Hey guys, I m in a bit of a bind at the moment. I have a session next weekend with a keyboard player who really wants to use the Arp Omni 2. It s pretty dead,
Re: Prophet 5 battery replacement.
2013-02-01 by imbuedblue
It s a BR-2/3A with PCB pins. I usually get them through Digikey or Mouser. The pins don t go through the PCB, but are bent and soldered to the component
Re: [vintagesynthrepair] Prophet 5 battery replacement.
2013-02-01 by Jim Blair
Thanks guys. I ll poke around and see what sources are available. Jim
Re: [vintagesynthrepair] Prophet 5 battery replacement.
2013-02-01 by PeWe
Well, that doesn´t look good even it´s only 4 entries. But a guy from Route66 is here in the group from time to time,- let´s wait what he says. ... Well,
Re: [vintagesynthrepair] Prophet 5 battery replacement.
2013-02-01 by Roger J
was wondering whoroute66studios was and found this: http://www.ripoffreport.com/directory/Route-66-Studios.aspx So what is with this? Friend or foe? ... a
Re: [vintagesynthrepair] Prophet 5 battery replacement.
2013-02-01 by Roger J
As I recall, it is a 3volt Lithium with tabs. About the size of 2/3 of a C. LIke a CR14250SE ... As I recall, it is a 3volt Lithium with tabs. About the size
Re: [vintagesynthrepair] Prophet 5 battery replacement.
2013-02-01 by PeWe
No, it´s not a 2032. Buy one here http://www.route66studios.com/batteries.html ... No, it´s not a 2032. Buy one here
Prophet 5 battery replacement.
2013-01-31 by Jim Blair
Hey! I m getting ready to do a battery swap on my rev3 P5. I haven t opened it up yet, but is the replacement simply a standard 2032 3V? Thanks, Jim
New arrivals in the shop this week.
2013-01-30 by Scott
All from the same new client: ARP AXXE , all original . Never serviced before Juno 60 , pretty much clean up and check settings TR-808 , go through all the
Re: Yamaha CS Slider switches
2013-01-28 by Boddington
Ha! You know I ve just assumed that a lot of the time they just don t stock these anymore, but it s well worth a shot! thank you for the reminder.
RE: [vintagesynthrepair] Minimoog power bulb.
2013-01-28 by Mark Wallis
Or just cut the end off and replace the neon and/or resistor. Insulate and reattach the end. To: vintagesynthrepair@yahoogroups.com From: ceratos@shaw.ca Date:
RE: [vintagesynthrepair] Yamaha CS Slider switches
2013-01-27 by Brian
Try Yamaha direct! Regards Brian G3OYU From: vintagesynthrepair@yahoogroups.com [mailto:vintagesynthrepair@yahoogroups.com] On Behalf Of Boddington Sent: 26
Off topic, but I'm Selling a Rhodes Suitace 88 Mark 1 in Vancouver BC Canada.
2013-01-27 by Gordon
Selling my early 70 s Rhodes. Craigslist ad below. I d rather keep it, but am limited by space and already have a Wurlitzer 145 as well as a Korg SV-1 and a
Re: [vintagesynthrepair] Minimoog power bulb.
2013-01-26 by Jim Blair
Thanks Keith.
Yamaha CS Slider switches
2013-01-26 by Boddington
Hello! Anyone got a lead on CS 5/10/15/30 2 position slider switches ... or perhaps a modern equivalent? I m on the hunt for a few. Since I m here, slider pot
Re: [vintagesynthrepair] Minimoog power bulb.
2013-01-26 by Keith Winstanley
Kevin Lightner: synthfool.com Exact replacement part :) It s a metal spring holds it in, I just use some pliers, the new lamp comes with a new plate sprin
Minimoog power bulb.
2013-01-26 by Jim Blair
Hey all, My Minimoog resto is coming along quite well. The new bushings are in, the bushing mounts are adjusted, and it s playing pretty nicely. The next step
Hiwatt custom tape echo service manual?
2013-01-24 by Terje Winther
Does anybody have the service manual for the Hiwatt custom tape echo? I have tried to contact Hiwatt, but all email accounts bounce. Terje Winther
RE: [vintagesynthrepair] Penfold modular
2013-01-23 by Jim Blair
Thanks John, I do have the schematics etc. I ve actually redone the pcb layouts to make them more accurate and readable. It s mainly diagnostics and
RE: [vintagesynthrepair] Penfold modular
2013-01-23 by John Rose
I think I may have a copy of that around somewhere, I will have to try and dig it out, if I remember correctly there was also one on Midi projects as well.
Penfold modular
2013-01-23 by Jim Blair
Hey guys, Many years back, I played around with the Penfold modular book. I built a bunch of circuits, and it worked ok. Not great, but it was a fun project.
Re: Roland PG-200 problem
2013-01-17 by Boddington
Hi there - I know this post is old but it s always sad to see an unanswered question. You ll see several 4051 multiplexer ICs in a row. Those interface between
Re: [vintagesynthrepair] Re: Emax floppy drive replacement.
2013-01-17 by jammie
fit a floppy emulator orget the scsi upgrade doneandfit ascsi to cf drive and a slim floppy drive and adapter ... From: dwv1957 To:
Re: Emax floppy drive replacement.
2013-01-16 by dwv1957
The drives from the ESI series if samplers will work in the Emax, these are the same drives that eprelectronics sells, if you want an original type
RE: [vintagesynthrepair] Re: VOX
2013-01-16 by Brian
Hi Very many thanks for that. Regards Brian G3OYU From: vintagesynthrepair@yahoogroups.com [mailto:vintagesynthrepair@yahoogroups.com] On Behalf Of imbuedblue
Re: [vintagesynthrepair] Calibrating Keyboard Velocity For Kawai K5000s
2013-01-16 by Roger J
Ok, then with a TP8, it leaves the possibility that the replacement mono pressure strip was thicker, preventing the second contact from making, unless the key
Re: [vintagesynthrepair] Calibrating Keyboard Velocity For Kawai K5000s
2013-01-15 by jammie
the kawai k5000 uses the tp8 same as the quasimidi cyber6 i fitted1 to an kawai k3 becuse the keys were nolonger available from kawai and a brand new tp8 from
Re: [vintagesynthrepair] Calibrating Keyboard Velocity For Kawai K5000s
2013-01-15 by jammie
yes thats most proberly right as they are 2 different heights take it back to the shop ... From: timothy kosiorek To: vintagesynthrepair@yahoogroups.com Sent:
Re: [vintagesynthrepair] Calibrating Keyboard Velocity For Kawai K5000s
2013-01-15 by Paul Krull
It s an issue of all keys having a threshhold where softly keyed notes do not sound at all. And it s not even that soft a keystroke that produces no note for
Re: [vintagesynthrepair] Calibrating Keyboard Velocity For Kawai K5000s
2013-01-15 by Roger J
Fatar keybed in a Kawai? As far as I know, with the exception of a few controllers that were made by other(like Panasonic) for Kawai, all of their actions and
RE: [vintagesynthrepair] Calibrating Keyboard Velocity For Kawai K5000s
2013-01-15 by timothy kosiorek
If it only plays at one loud volume they might have installed the rubber contact strips backwards.Tim K.
Re: [vintagesynthrepair] Calibrating Keyboard Velocity For Kawai K5000s
2013-01-15 by jammie
sounds like they never cleaned the contact correctly its a fatar keybed anduses the double rubber contacts per key if keys are pressed gently they hit the
Calibrating Keyboard Velocity For Kawai K5000s
2013-01-15 by Paul Krull
So I picked up my K5000s that has been in the shop since early April after they fixed aftertouch and the back light. Now lower velocity keystrokes do not
Re: VOX
2013-01-15 by imbuedblue
http://www.cruses.se/cam/Cambridge%20Mod%20.rar
VOX
2013-01-15 by Brian
Hi All Not a synthesizer but hopefully someone here can assist me. Where can I get a schematic for a Korg Vox Cambridge 30 Reverb amp? Regards Brian G3OYU
RE: [vintagesynthrepair] Emax floppy drive replacement.
2013-01-15 by Lorne Hammond
I agree. They are the place for emu support. The only other place in this league is Bruce Forat for sp-12/1200s. Nice people, I remember talking with them
Re: [vintagesynthrepair] Emax floppy drive replacement.
2013-01-15 by Roger J
www.eprelectronics.com ... www.eprelectronics.com From: z z To: vintagesynthrepair@yahoogroups.com Sent: Monday, January 14, 2013 3:19 PM
Emax floppy drive replacement.
2013-01-14 by z z
Hey folks. Looks like I have a dead floppy drive on the Emax SE HD. It s the early battleship, grey rather than black. Any sources that you d recommend?
Re: Moog Source challenges.
2013-01-12 by synthparts
The first thing I check on a Source is this - http://www.synthfool.com/docs/Moog/crazysource_mod.jpg Doug synthparts.com
Re: [vintagesynthrepair] Moog Source challenges.
2013-01-12 by Paul Cunningham
Sounds like you need to get a copy of the service manual and go through that first. You don t really need a oscilloscope to make the adjustments, just a good
Moog Source challenges.
2013-01-12 by z z
Hey guys. I picked up a Moog Source yesterday. And of course, it doesn t work properly. The synth is in perfect cosmetic condition, with a beautiful membrane
KORG NS5R - l.e.d backlight source
2013-01-09 by NoëlBuhagiar
Hi, I have for repair an NS5R module with a faulty backlight. Backlight is of 2 colour multi l.e.d.s type, red & green. Anyone know of a source where I could
Re: [vintagesynthrepair] Re: Korg Guitar Synthesizer X911
2013-01-07 by Daniel Forró
So should I suppose that old NEC D4069C chip was unbuffered and order modern equivalent with UB suffix? I still couldn t find datasheet for old chip. I d like
Re: [vintagesynthrepair] Re: Roland JX3P Faulty
2013-01-07 by Nick Bell
Thanks John, that s really good to know. I found a few TLO72 s on ebay. Best Nick ________________________________ From: John Rose
RE: [vintagesynthrepair] Re: Roland JX3P Faulty
2013-01-06 by John Rose
If you have a problem getting them let me know as I can get hold of most items and am in the UK Many thanks John Rose (www.astrodevelopments.com) From:
RE: [vintagesynthrepair] Re: Roland JX3P Faulty
2013-01-06 by Nick Bell
Thanks both - it s a dip, will prob try the TL s best Nick
RE: [vintagesynthrepair] Re: Roland JX3P Faulty
2013-01-06 by John Rose
I have just had a quick look in my box of opamps and have both the RC4558 and the MC1458 which are equivalent and I can get hold of these still for pennies,
Re: [vintagesynthrepair] Re: Roland JX3P Faulty
2013-01-06 by jammie
the 4558 op is a very noisy opamp you can change them for the tlo8/7 series dual opamps is it a dip or a ziff 9pin ic as in the korg dss1 they are ziff 9 pins
Re: [vintagesynthrepair] Korg M500 Micro-Preset problems.
2013-01-06 by Jim Blair
Thanks for the service manual link. I really appreciate it. I ll probably open up the synth later today. Hopefully it s just dirty connectors and other easy