Yahoo Groups archive
Messages
Page 4 of 168 · 8362 messages matched
2011-10-23 by Liese, HaJo
Hi Collin, I want to update my P3 Version 3.1 006 to a newer version - Netbook with XP - Edirol UA 20 Midiinterface - loaded the system V4.5 - Sending SYSEX - I have a Stdiomaster MA36 Midi checker, the data are pasing trhu percectly - I did connect to the P3´s MIDI IN port Nothi
2011-10-18 by Bouncer
OK i 've found it in the sequentix web site...sorry --- In analogue-sequencer@yahoogroups.com, "Bouncer" wrote: > > hello where the os P3 ve 4 ,cause i ve got once more time a CHK fail error...thanks >
2011-10-18 by Bouncer
hello where the os P3 ve 4 ,cause i ve got once more time a CHK fail error...thanks
2011-10-16 by Bouncer
Hello,i ve built the two versions early,and later,i think it' s the I/O midi which is different ,only one midi in.out on the early board..perhaps some little difference (resistor) with the lcd and a Pled One advice,buy a extension ram to Colin and buy only one old memory..for the
2011-10-16 by peter_ivens
Hello, I am new to this forum. I can buy a set of P3 PCB's v1.3 + a processor. I have found some messages about people who constructed a P3 with these PCB's using the BOM still on the sequentix web site. There is a slight differance in components between all the PCB versions. Is
2011-10-14 by echojordanfieldstation2
Thx colin, Would it be possible to buy a few from you? cheers, Kind regards, --- In analogue-sequencer@yahoogroups.com, "sequentix" wrote: > > > > Can anybody tell me where the nice buttons from the Cirklon come from and with what type of Cherry switch they work? > > They are UK
2011-10-13 by synthdance
Hello, I am interested in Cirklon, I've been at Sequentix website, YouTube and of course, I've read all messages here. Few questions I couldn't find the answers for: 1. When defining a synth (name, midi port and channel), can bank select and program change command be also specifi
2011-10-13 by Colin f
> How do I make Sculpt and Randomize automatically set the Gate > bit to "ON"? In the 5 years I've had my P3 it always worked > that way, but now I've messed something up and suddenly they > no longer auto-activate. Can anybody help me find the switch > for this? Are you sure you
2011-10-12 by Keith Sterling
How do I make Sculpt and Randomize automatically set the Gate bit to "ON"? In the 5 years I've had my P3 it always worked that way, but now I've messed something up and suddenly they no longer auto-activate. Can anybody help me find the switch for this? [Non-text portions of this
2011-10-02 by Barbara Fraser, Sequentix
--- In analogue-sequencer@yahoogroups.com, "John" wrote: > > > --- In analogue-sequencer@yahoogroups.com, "Barbara Fraser, Sequentix" wrote: > If you would like to order from the next production run and have not already emailed me, please email sales@ and I'll add you to the wait
2011-10-02 by John
--- In analogue-sequencer@yahoogroups.com, "Barbara Fraser, Sequentix" wrote: If you would like to order from the next production run and have not already emailed me, please email sales@... and I'll add you to the waiting list. I will email customers for the 2nd run again in earl
2011-09-27 by Colin f
They are not the same, but give similar results. Gate mode 2 lets you set a series of steps to the same note, and tie them together, so that the note plays over multiple steps. The note value is changed on every step. Length 13 makes the note set on a single step hold until the n
2011-09-25 by Corte Italiano
Hello, I bought an early P3 and learning how to use. I prefer version 3 than 4. I don´t understand gatemode2 Is any way to turn off the screen on OS 3 ? Thanks [Non-text portions of this message have been removed]
2011-09-25 by p3acidman
I mean gate mode2 is not the same as lenght 13? --- In analogue-sequencer@yahoogroups.com, Corte Italiano wrote: > > Hello, > > I bought an early P3 and learning how to use. > > I prefer version 3 than 4. > > I don´t understand gatemode2 > > Is any way to turn off the screen on O
2011-09-23 by John
Ian how is the Cirklon + Logic intergration working now? Can I ask if you use an external mixer for your hardware synths, and then route that to Logic + audio interface? I use no external mixer, but have all my synths going into inputs on my audio interface, going through softwar
2011-09-22 by Colin Fraser
> I have a P3 without mem exp. How much is the mem exp new now? I haven't sold a MemX in a long time... but I still have some boards. New price is 58.75ukp (roughly 66 euros, depending on the exchange rate at PayPal). Best regards, Colin Fraser Sequentix Music Systems Ltd http://
2011-09-22 by Liese, HaJo
Hello, I have a P3 without mem exp. How much is the mem exp new now? Hajo Germany, Düsseldorf _____ Von: analogue-sequencer@yahoogroups.com [mailto:analogue-sequencer@yahoogroups.com] Im Auftrag von multibises Gesendet: Donnerstag, 22. September 2011 17:25 An: analogue-sequencer@
2011-09-22 by multibises
hi there, i've got a brand new memx board for P3 sequentix. in original box and never opened ! i ask 50 euros ! located : marseille ≤ france. Mo
2011-09-19 by Colin f
> However Logic does not set it's tempo to that of the Cirklon. > I'm getting clock messages in the midi monitor, so they are > leaving ok. The idea is to set a MTC slaved device to the same tempo locally. MTC provides a linear time reference, so if both devices fit the same numb
2011-09-19 by Ian Mantripp
On Tuesday 20 September 2011 at 00:23, Colin f wrote: > Is Logic set to start from timecode 00:00:00:00 ? Mr Fraser, you are an ace :-) However Logic does not set it's tempo to that of the Cirklon. I'm getting clock messages in the midi monitor, so they are leaving ok. oh well th
2011-09-19 by Colin f
> Anyone have any ideas ? Is Logic set to start from timecode 00:00:00:00 ? That's where Cirklon starts from. Logic will need to have the same idea. I'm told that either 00:01:00:00, or some other time is a 'more standard' starting point for video production. Something to do with
2011-09-19 by Ian Mantripp
On Sunday 18 September 2011 at 15:43, John wrote: > Is MMC enabled in Logic? "Midi machine control" transmits remote control of Play, Fast Forward, Rewind, Stop, Pause, and Record functions. ok, so I've just tried again. Setting MMC doesn't change anything. The play and stop work
2011-09-19 by John
--- In analogue-sequencer@yahoogroups.com, Ian Mantripp wrote: > Now I have noticed something that could give some indication of what's happening. When I press record in Logic and then play on the Cirklon, I get the usual recording dialog in Logic, but the bar indicator seems to
2011-09-18 by Ian Mantripp
On Sunday 18 September 2011 at 00:33, John wrote: > Just been re-reading this old thread... > Paul you were able to use Logic as a slave, with Cirklon as the master. Which version of Logic would this be? If i'm not mistaken Logic can't slave to midi clock since version 7. Not sur
2011-09-18 by John
Is MMC enabled in Logic? "Midi machine control" transmits remote control of Play, Fast Forward, Rewind, Stop, Pause, and Record functions. John --- In analogue-sequencer@yahoogroups.com, Ian Mantripp wrote: > > > > On Sunday 18 September 2011 at 00:33, John wrote: > > > Just been
2011-09-18 by John
--- In analogue-sequencer@yahoogroups.com, Ian Mantripp wrote: > I've tried this but I cannot get Logic to record. > It seems to not be receiving the incoming audio data. I've tried with all the core audio sync mode settings but I've not yet succeeded. > > Ian > I've not actually
2011-09-18 by Ditton33
Hi Could be a few things. Check the last step setting, or perhaps the steps are skipped. Also if I were you I'd initialise the P3 (presuming it wasn't new) so you are starting with a clean sheet. All in the manual but shout if you need help. > >-----Original Message----- > >From:
2011-09-18 by jdchevallier
Seems like it was indeed the last step setting. Thanks for the tip. I'm going to reinstall the os and start from scratch! I'll try not to inundate the board with questions I can easily find in the manual going forward guys! Joel --- In analogue-sequencer@yahoogroups.com, "Ditton3
2011-09-18 by jdchevallier
Hello everyone. My P3 came in wednesday and I'm just sitting down with it. I'm running os 3.1, and hit a a a bit of a wall right off the bat. As I go into Pattern Edit mode, depending on the bank I'm in, the patterns just cycle through either 3 steps, or linger on the first. I ca
2011-09-17 by John
--- In analogue-sequencer@yahoogroups.com, Paul Nagle wrote: > On the MTC front, I've tested it with Logic now as master and slave and > it works fine. Or it does once you tell Logic to start at 00:00:00 > rather than 01:00:00 > Paul Just been re-reading this old thread... Paul y
2011-09-16 by Steve G
Thanks for the info, Sadly, due to vet bills for my poor dog (straight after my massive renovations), I can't afford a Cirklon now. I've told Barbara with much sadness. I will be trying to purchase this p3 though so I can at least enjoy that and get ready for a Cirklon next year
2011-09-16 by Ditton33
I have both. Mainly because I'd never part with my P3. It's nice having one track open to fiddle with directly. And if a P3 OS ever does appear which makes it an extended work surface for the Cirklon that would be neat. But in most respects the Cirklon is so superior it's no cont
2011-09-13 by digitalbunny81
Great news, thanks Paul. Sounds like a great combo, being able to record external tweaks via the Cirklon. Very excited. I just paid off the Moog Voyager XL just minutes ago and am looking at the Vermona DRM1 MK3 as well, so the Cirklon will certainly give them a smashing! Cheers
2011-09-13 by Paul Nagle
On 13/09/2011 00:39, digitalbunny81 wrote: > Ahh ok, > Thanks Paul > So just to get my head around this (i've been skimming the manual, but haven't really got my head around this sort of part) - can you have the 'mixer' page open at the same time as changing parts/patterns etc? T
2011-09-12 by digitalbunny81
Awesome news on CVIO! When you ship it, say it's under 1000 and call it a gift and i will kiss you!! Wow... that's pretty amazing then. So when you're 'jamming' away, you could have the Cirklon on record and it would store all the data sent from an external midi controller!? Yike
2011-09-12 by digitalbunny81
Ahh ok, Thanks Paul So just to get my head around this (i've been skimming the manual, but haven't really got my head around this sort of part) - can you have the 'mixer' page open at the same time as changing parts/patterns etc? That would indeed make an external box redundant..
2011-09-12 by Colin f
> > I'm Steve and i have a Cirklon on order... go me (i've sent > an email requesting an upgrade to CVIO, i hope i can get it). Adding a CVIO is no problem. Barbara will confirm when she gets back to work. > > Anyway, i was wondering for live use/improv, could i > potentially run
2011-09-12 by Paul Nagle
On 12/09/2011 02:23, digitalbunny81 wrote: > Hey all, > I'm Steve and i have a Cirklon on order... go me (i've sent an email requesting an upgrade to CVIO, i hope i can get it). > > Anyway, i was wondering for live use/improv, could i potentially run my bitstream 3x through the C
2011-09-12 by digitalbunny81
--- In analogue-sequencer@yahoogroups.com, "Derek" wrote: > > I have a P3 for sale. It is in excellent condition and has the expanded memory. Price $600. Location: Worcester, South Africa > Shipping to be covered by the buyer. > Derek > Any photos? I wonder if a P3 and a Cirklon
2011-09-11 by digitalbunny81
Hey all, I'm Steve and i have a Cirklon on order... go me (i've sent an email requesting an upgrade to CVIO, i hope i can get it). Anyway, i was wondering for live use/improv, could i potentially run my bitstream 3x through the Cirklon to change levels etc on other gear? i.e. con
2011-09-08 by Derek
I have a P3 for sale. It is in excellent condition and has the expanded memory. Price $600. Location: Worcester, South Africa Shipping to be covered by the buyer. Derek
2011-09-07 by duncan
>>Many years ago, I had a Cheetah MQ8.
2011-09-06 by Mark Morton
Where are you located? On Mon, Sep 5, 2011 at 7:13 PM, Joel chevallier wrote: > ** > > > Hi everyone! > After looking at various hardware sequencing options I've settled on a P3 > since the Cirklon isn't available. Any chance anyone has one for sale? > > Thanks! > Joel > > Sent f
2011-09-05 by Joel chevallier
Hi everyone! After looking at various hardware sequencing options I've settled on a P3 since the Cirklon isn't available. Any chance anyone has one for sale? Thanks! Joel Sent from my iPad
2011-09-05 by jdchevallier
Hi Mark, I'm in San Francisco. Thanks! Joel --- In analogue-sequencer@yahoogroups.com, Mark Morton wrote: > > Where are you located? > > On Mon, Sep 5, 2011 at 7:13 PM, Joel chevallier > wrote: > > > ** > > > > > > Hi everyone! > > After looking at various hardware sequencing opt
2011-09-01 by hans wurst
propably an already answered question, but the information on the web is somehow confusing...can someone tell which filters are built in the different version of the ppg wave (2/2.2/2.3)?thankskris [Non-text portions of this message have been removed]
2011-09-01 by John
Im pretty sure the Wave 2 had the CEM3320 , and the 2.2/2,3 had the SSM 2044 filter chips. Wish i had one... Cheers, John --- In analogue-sequencer@yahoogroups.com, hans wurst wrote: > > propably an already answered question, but the information on the web is somehow confusing...
2011-09-01 by John
--- In analogue-sequencer@yahoogroups.com, "Colin f" wrote: > There is already code for reading and writing Cirklon's own data in .SYX > format, so suppose it should be pretty easy to add a MIDI librarian thing at > some point. > > Cheers, > Colin > That would really be cool Coli
2011-09-01 by Colin f
> I've loads of Sysex patch banks on my computer which i send > via a Sysex dump program to my various synths when working > with my DAW. > Is it possible to do the same with Cirklon, and have all the > sysex banks stored in memory (and upon power down) , call up > the sysex bank
2011-09-01 by j5r9pn3lka
Yesss! I was thinking exactly to make a post about that, in the spirit of "eliminate all computers when possible", while I was stupidly and unsuccesfully trying to sysex-dump some seqs I've had made using the internal seq of the futureretro777, to the Cirklon. And the same about