Yahoo Groups archive
Messages
Page 120 of 155 · 7723 messages matched
2005-03-25 by Ricardo Verschut @ Jura Music Production
Hi, I know of an editor for the VZ1pro that works fine on TOS 1.4. I m not sure if it will be compatible with the Falcon s OS. Neither do I know if it will
2005-03-24 by Stephen Nichols
On the Solus, the lack of an independent volume control makes it tough to isolate the effect on ADSR and/or filter. No 60Hz hum...seems to happen regardless
2005-03-24 by Larry T.
Hello All Is anyone aware of a patch editor/librarian for the Casio VZ synths that runs on the Atari ST/TT/Falcon systems? Also, I have just received an Atari
2005-03-23 by Mike Walters
Does it do that when the envelope controls both the filter and amp? When you say it sounds like a cable being tapped, do you hear a 60Hz hum for a second? Or
2005-03-23 by easterleggs
Hello to all. My ARP SOLUS produces a thump whenever the envelope triggers. It s not a mechanical noise...it s akin to tapping the end of a cable while
2005-03-22 by Keith Niver
I take it you did try to go into the menus and adjust the contrast or do a hard reset. If you aren t familiar with how to do that, go to Roland s web site and
2005-03-20 by AveMarn
Hi, Got this unit dead in for repair which has been butchered so to speak,had the ca5668 soldered in reverse replaced it,managed to get the psu and main amp
2005-03-20 by rtubbs@acc-net.com
Keith and Group, Keith, I tried emailing you off-list a couple times but got no reply. Probably the victim of a spam filter somewhere. Anyhow, I found the
2005-03-20 by noteit@juno.com
Hi again Larry, This is the Holy Grail when it comes to the FZ (this, and backing up the OS- but it looks like that might soon be answered ;) ). Anyhow,
2005-03-20 by synthflake
Anyone know if a Roland JV880 display can be repaired? The display is good but there is no backlighting. It makes it a little hard to make out. If it can t be
2005-03-20 by Larry T.
Anyone know what 1.44Mb floppy drives are compatible with these samplers? I need to replace the drive in my FZ-20M. It is still working (for the moment) but
2005-03-19 by Daniel J. Litwin
Hello, looking to replace the C6 key on my Emu Emax II. This is the topmost C key on the keybed. I believe Fatar was the manufacturer of the keyboard
2005-03-19 by dave woodall
Hey Everyone, Just posting for a friend. No interest in, personal involvement with, etc, etc. I will say though that I found Tavilla (the seller) very
2005-03-18 by Sandra Garcia
try http://kidnepro.com/ Larry T. wrote: I just managed to snag an FZ-20M on eBay. However, it did not come with the floppies of
2005-03-17 by Larry T.
I just managed to snag an FZ-20M on eBay. However, it did not come with the floppies of optional software, and one of them is cirtical in order to install a
2005-03-17 by arp2600fan
... Take your time. Mistakes are magnified when you go faster. Careful removing the springs. Make note of which color spring goes to which type of key (sharp
2005-03-14 by easterleggs
I have an Octave Cat (not SRM) with a few sliders that are very resistant to movement. They function but not in a readily tweakbale way. I ve tried contact
2005-03-13 by Keith Niver
Hi Rich Contact me off list and I will try and help you through this problem. I don t think it s in the keying box. More likely it might be a dirty chime
2005-03-13 by richmarionohio@yahoo.com
I have a Wurlitzer 4520 (the theater horseshoe version of the 4500 series) which has one or more problems in the lower manual keying circuit(s). The Melodia
2005-03-12 by Dale Kay
Looking for a schematic for Mini XLPC photosensor analog Theremin. If you know of one similar, drop me a note too. dale
2005-03-11 by roland_w_30
If anybody has these, please be so kind and save me...
2005-03-11 by shaynecafferata
my newly acquired sbx-10 has a tempo problem. when i got it, one of the pads(for the tempo knob) on the pcb was lifted. i desoldered, scraped away some of the
2005-03-11 by timothy kosiorek
Hello:Its also an electronic piano,but I think its from the late 80 s or 90 s,I checked around and Mark Glinsky has a CP-30 service manual on his website here
2005-03-11 by dl_woodall
Hey Tim, Thanks but unfortunately no; definitely CP-30. It s an electronic piano from mid to late 70 s. What s a CLP-30? regards, dave woodall usa ... Needed
2005-03-11 by timothy kosiorek
Hello:Is this a CP-30 or a CLP-30?I have the CLP-30 service manual. Tim K. ... direct link to my Ebay store. http://www.sonicelectronicmusic.com
2005-03-10 by dl_woodall
Just bought a CP-30 in pretty good condition with the exception of the keyboard felt and a few keys that are sticking and/or need their resting height
2005-03-09 by roland_w_30
Hey As you might guess, battery leakage. The DCO1 is dead. And the polyphony is lame. Every sixth note plays false sound [too high cutoff and...just
2005-03-07 by Brian Fuller
Have you tried Roland? I replaced an entire Juno 106 Pitch Bender assembly a few years ago. I don t know what their inventory is like now. I believe I still
2005-03-06 by masada wilmot
http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&category=38090&item=7305307223 &rd=1 good ol chipforbrains... mw ... From: djbrow54
2005-03-06 by Sandra Garcia
... ??Tried Ranger Audio??
2005-03-06 by djbrow54
I m restoring a Juno-106 which was missing one of it s voices. I was lucky and it was in the digital control circuitry. However, the bender module has some
2005-03-06 by cyrille
yeah thanks also asked on the ody group i tried to do it with the schematics i had found on the website you re talking about, but there s not everything and i
2005-03-06 by Elliott O'Mara
I second that actually (should have read this before replying to said message!) Elliott
2005-03-06 by Elliott O'Mara
Cyrille, You should check out the ARP Odyssey resourse page: http://www.arpodyssey.com/index.html There are lots of useful schematics/picture/instructions and
2005-03-06 by cyrille
hi all first i need to explain what we have here a mk2 black odyssey with a white vcf board it s in europe, so needs 230 vac at this time the supply is not
2005-03-06 by bdrjct
sorry you re right about risks with bmps i ll try and add it somewhere bye ... from unknown ... messages, I ... infected ... instance you ... that you ... the
2005-03-06 by Brian Davies
Hi Guys and gals. I don t know about the rest of you but I don t like attachments from unknown sources! This is especially true if they come with unsigned
2005-03-06 by cyrille
hi all first i need to explain what we have here a mk2 black odyssey with a white vcf board it s in europe, so needs 230 vac at this time the supply is not
2005-03-04 by Rick
a friend just got a TR808.. looks and works good but the hand clap level is kind of low compared to the other sounds in the mix output. the panel HC/MA level
2005-03-03 by josephex@josephexperimental.com
I just got a Korg DW 8000 and noticed a kind of similar problem...think it could be dirty key contacts as well? Normally it ll stay in pitch, but occasionally
2005-03-03 by Mike Walters
Dirty key contacts? ... only
2005-03-03 by synthiaks2004
Dear All Any body can give me a help. My Minimoog had some problem on the keyboard. Actually it got some problem only on the particular keys. When I press the
2005-02-26 by The Old Crow
All the FETs are typical 2SK30(A) JFETs. You can either order some 2SK30As from a place like americanmicrosemi.com or just use a general-purpose modern part
2005-02-25 by Sandra Garcia
just trying to help. thanks for the link--for the future--for in case Don t t(h)read on my tentacles, Earthling! wrote: ...
2005-02-25 by Don't t(h)read on my tentacles, Earthlin
... mhmm interesting (gear lust syndrome) Thanks to ac on AH, got the answer! http://www.pricedata.co.uk/bagse/backlights.htm Denis =G)
2005-02-25 by Sandra Garcia
also try http://summitartists.com/telesis/cat.htm Don t t(h)read on my tentacles, Earthling! wrote: ... Thanks! Haven t been
2005-02-25 by Don't t(h)read on my tentacles, Earthlin
... Thanks! Haven t been there for months, but didn t see the ad… :-/ I ll pass the info to the guy in need of one… Denis =G)
2005-02-25 by bitexion
... Exactly the kind of thing I was hoping to see :-) I ll check out the other links aswell. We re talking a MOS-FET transistor here? Standard electronics
2005-02-25 by The Old Crow
Educated guess as this has happened to Korg VCOs in other instruments: replace the FET F3. Crow /**/
2005-02-25 by Sandra Garcia
sonic state advertises LCD backlights Don t t(h)read on my tentacles, Earthling! wrote:http://www.backlights.co.uk/ is down for