Syn-Key Questions
2011-08-29 by Boddington
Hi folks! Can anyone enlighten me on the Syn-key a bit? - I keep hearing that only about 30 were made but I sort of don t believe that. I ve seen a handful
Messages
Browse messages
Page 3 of 14 · 679 messages matched
Re: EML 500 Help
2011-08-24 by Van Santos
Thanks, Laurie! I haven t had a chance to take pictures of the unit, busy with work this week. I ll check out the resource you listed to see if there is
Re: EML 500 Help
2011-08-24 by laurie_spiegel
Also, though these docs might be in the group s files (I didn t look) there is an EML Owners Manual and a Service Manual here, along with other Electrocomp
Re: EML 500 Help
2011-08-24 by laurie_spiegel
Hi Van, and welcome here. Maybe this will help: http://www.cem3374.com/docs/Manuals/EML/400_SM.pdf Or maybe it won t. There seems to be enough interest in
EML 500 Help
2011-08-19 by van_m_santos
Hi All, A fellow group member suggested I join, so here I am. I have an EML 500 that I m looking to use my Kenton ProSolo MK2 on; however, board has no
RE: [emlsynth] Re: How do you use the EML Envelope Follower? (lil yellow box)
2011-08-18 by George Mattson
It could be of use. You d just have to figure out how to get +/-15VDC to it. The +/- VDC output out of the 401 is Tip: +15V, Ring: -15V and sleeve is ground.
Re: How do you use the EML Envelope Follower? (lil yellow box)
2011-08-18 by Doug
That MUST be extremely rare. In all my dealings with EML, I didn t know that they might have packaged their units in an enclosure such as this. That also begs
RE: [emlsynth] Re: How do you use the EML Envelope Follower? (lil yellow box)
2011-08-18 by Prosper Prodaniuk
So as an EML 100 owner then this box would have no use for me without modification? It s not just plug and play?
RE: [emlsynth] Re: How do you use the EML Envelope Follower? (lil yellow box)
2011-08-18 by George Mattson
Ah, Doug, you re getting old :) The 401 has a +/- voltage out jack between the Vext input and the trigger out on the lower left of the panel. It requires a TRS
Re: How do you use the EML Envelope Follower? (lil yellow box)
2011-08-18 by ukrainiannproud
Here is a link to the one on Ebay. The one locally looks exactly the same except it has the original EML knobs.
Re: How do you use the EML Envelope Follower? (lil yellow box)
2011-08-18 by Doug
To my best recalections, the none of the EML synths had any sort of DC power output jacks. Would have been nice though. I have to assume you are referring to
How do you use the EML Envelope Follower? (lil yellow box)
2011-08-18 by ukrainiannproud
I first saw one of these on the bay about a month ago (still there, crazy expensive) but have an opportunity to buy one locally for much less. I want to buy it
Re: [emlsynth] Re: Electrocomp-101 with a Doepfer Dark Time?
2011-08-13 by Matt
Doug, it s not possible to control all 4 VCOs from the jacks on the 101 - it has been suggested here in older posts that the only that might be possible is via
Re: Electrocomp-101 with a Doepfer Dark Time?
2011-08-12 by Doug
It has been a VERY long time (1970 s) since I worked on a 101, but don t recall why there might be interface problems - not to say that there aren t any. (I
Re: [emlsynth] Re: Electrocomp-101 with a Doepfer Dark Time?
2011-08-12 by Matt
Hi Oliver, Initially it can be a source of frustration that the EML synths won t sync with anything else (it s partly the 1.2v/oct and partly the weirdness of
Re: Electrocomp-101 with a Doepfer Dark Time?
2011-08-12 by Oliver Chesler
Hi Matt, Thanks for the heads up. I thought that was the answer but I was double checking. I m using the Dark Time with some other gear (really nice little
Re: [emlsynth] Electrocomp-101 with a Doepfer Dark Time?
2011-08-12 by Matt
Search the archives and you ll see the issue of compatibility between the EML synths and everything else discussed several times, however, the short answer to
Electrocomp-101 with a Doepfer Dark Time?
2011-08-12 by Oliver Chesler
Hello Everyone, Is it possible to control an Electrocomp-101 with a Doepfer Dark Time analog sequencer? I have both but can t seem to get it to work. If it is
Re: converting 1.2 volt/octave to 1 volt/octave
2011-08-04 by Boddington
As far as I know there are two issues at play for HZ/V/Oct. 1 - The octave scaling everyone talks about. Technically you can calibrate one octave between the
Re: [emlsynth] Digest Number 315
2011-07-30 by brianfolkes@cox.net
I have never gotten my EML101 (older, pre-Sequencer input jack) to respond to either V/Oct nor Hz/Oct. My understanding is it is V/Oct but it is 1.2 volts per
Re: [emlsynth] Re: converting 1.2 volt/octave to 1 volt/octave
2011-07-29 by rjeancarlo c
yeah the EML200 s oscillators are hz/v. ... From: Nick Zampiello Subject: Re: [emlsynth] Re: converting 1.2 volt/octave to 1
Re: [emlsynth] Re: converting 1.2 volt/octave to 1 volt/octave
2011-07-21 by Nick Zampiello
So, i knew something was confusing and i looked into my old emails... dave wilson of NESM had explained it to me before and i just remembered it backwards:
RE: [emlsynth] Re: converting 1.2 volt/octave to 1 volt/octave
2011-07-21 by George Mattson
The 200 is basically just a bare integrator IC with a UJT, cap and diode network in the feedback loop. The center frequency and both swings are all summed
Re: [emlsynth] Re: converting 1.2 volt/octave to 1 volt/octave
2011-07-20 by Nick Zampiello
umm, now i m confused! sorry... z NEW ALLIANCE EAST!!!! ... http://www.newallianceeast.com http://www.newallianceaudio.com
Re: [emlsynth] Re: converting 1.2 volt/octave to 1 volt/octave
2011-07-20 by sprgroups@o2.co.uk
... Are you sure about the 200? The schematic I ve seen looks like a V/Hz oscillator. Or was there a later version of the 200 (201?) Steve
Re: [emlsynth] Re: converting 1.2 volt/octave to 1 volt/octave
2011-07-19 by Nick Zampiello
i never had any luck trying to get the EML to track to any hz/volt synth... it just can t scale that far beyond 1.2 v/oct... the way the controls are on mine
Re: [emlsynth] Re: converting 1.2 volt/octave to 1 volt/octave
2011-07-19 by Prosper Prodaniuk
I know the difference i just had heard hz/v mentioned for them. A guy playing his with a MS-20 etc. On 2011-07-19 12:15 PM, Nick Zampiello
Re: [emlsynth] Re: converting 1.2 volt/octave to 1 volt/octave
2011-07-19 by Nick Zampiello
The 200 and 101 oscillators are a non-standard 1.20v/oct hz/volt is more of a japan convention: korg, Yamaha, etc... i can get mine to tune to other 1v/oct
Re: converting 1.2 volt/octave to 1 volt/octave
2011-07-19 by Prosper Prodaniuk
Maybe in this someone can answer whether or not the 200 (and 100) are HZ/V as opposed to V/OCT and then they went with the V/OCT convention for the 101 and
converting 1.2 volt/octave to 1 volt/octave
2011-07-19 by Nick
... Hello, i was noticing some discussion about changing the EML 101 to 1v/octave... is it possible to do this on the EML200 as well? is it really just a
EML Poly Box relisted with no reserve price
2011-07-13 by steve13dejesus
Hi again, The auction I had for an EML Poly Box on Ebay closed without meeting the reserve price, so I have relisted it today in a new auction with no reserve
EML Poly Box for sale on Ebay
2011-07-07 by steve13dejesus
Hi, Just a heads up that i have posted a mint EML Poly Box for sale on Ebay.
Re: EML 101 Glide circuit weirdness?
2011-06-22 by steve13dejesus
Thanks for your input. I think this circuit is dedidedly different from the schematic I have. There is a small realy on the board that one of the wires from
Re: EML 101 Glide circuit weirdness?
2011-06-22 by Doug
Schematic differences are odd indeed. However, I d suspect at it s age, you ve likely got a leaky portamento cap that needs replacing. Looks like 15uf on
Re: EML 101 Glide circuit weirdness?
2011-06-22 by steve13dejesus
I forgot to mention that the op amp that the glide knob fixed leads connect to is an LM748, not the LM741 shown in the schematic. There is another LM 748 just
EML 101 Glide circuit weirdness?
2011-06-22 by steve13dejesus
Hi all, I have an EML 101, S/N 278, that is in perfect condition except for some strange behavior in the glide circuit. With the glide knob fully counter
eml200 reverb tank
2011-05-16 by Brian Arthur
hi, if i need to replace the accutronics tank can anyone suggest which model i should get? thanks
FYI I just uploaded a picture
2011-05-13 by laurie_spiegel
This one:
hello! eml200 reverb
2011-05-13 by arthurb64
I perhaps should have mentioned that my 200 is a single panel silverface. B
.....hello! eml 200 reverb
2011-05-13 by arthurb64
hi everyone, i acquired a 200 recently, it had been sitting unused(for quite some time i,d imagine) in Constantine public schools, Michigan (as engraved in the
WTB: EML 400 and greeting
2011-03-15 by ATS
Hello everyone, Somehow I ve made it this far completely unaware of this EML list. Thanks for keeping a forum open specifically for EML equipment. I am
Re: EML-200 owners?
2011-03-02 by Doug
I don t own a 200 currently, but I was EML s first New Jersey Rep / Service center. I might be able to help.
EML-200 owners?
2011-03-02 by mm123 ah
hi guys if anyone s got an eml-200 on hand, can you please email me at minime123 at onebox dot com? (dont just press reply as i dont check this account often)
RE: [emlsynth] Re: new member - 1010 OSC2 question?
2010-12-01 by George Mattson
I d check to see if the CV path from the select switch to the VCO is intact. _____ From: emlsynth@yahoogroups.com [mailto:emlsynth@yahoogroups.com] On Behalf
Re: [emlsynth] Re: new member - 1010 OSC2 question?
2010-12-01 by Matt
I don t service my own synths and am not at all technical but if you can t work out from the service manual what the problem is then you need a tech. I assume
Re: new member - 1010 OSC2 question?
2010-12-01 by dramirezpa
Thanks for the response. Any idea what might be causing it to be operable but in LFO range? I ll be taking it apart for a thorough cleaning soon and although
Re: [emlsynth] new member - 1010 OSC2 question?
2010-12-01 by Matt
OSC2 is an audio frequency oscilator so it seems your EML 101 is in need of a service. The only VCOs that operate in the LFO range are OSC1 & OSC4
new member - 1010 OSC2 question?
2010-12-01 by dramirezpa
Hey guys, just found this forum. Also just acquired an eml 101. So OSC2 seems to be making subsonic oscs. Reading the user and service manual it seems like
Re: EML 301 Mystery
2010-09-10 by Doug
Sigi, I m In South Central NJ. If you want to get your 301 to me, I think I can repair it for $100 or less. I can t tell how much damage has been done until
Re: [emlsynth] Re: EML 301 Mystery
2010-09-10 by Alaric Vltor
Pictures from my phonecam are uploaded in folder titled Nihilist Mod Boxes. This Eml system was obtained in New Jersey ten years or so ago from someone who had