Re: [emax] Emax2 Memory Files
2016-02-04 by schtom83318@...
I don t have a chip reader so I might just be stuck in doing the scrambled megs. If you can see what the chip numbers are, I d appreciate it. thanks, Tom
Messages
Browse messages
Page 4 of 236 · 11758 messages matched
Re: [emax] Emax2 Memory Files
2016-02-04 by anthony kirby
Hi Tom, I bought them from ebay and from memory they were from a seller in the USA. It was a little while ago now. I can check the chip numbers for you when
Re: [emax] Emax2 Memory Files
2016-02-04 by schtom83318@...
Tony, Can you tell me what memory chips you bought and where you got them? I need to by 32 of them to get mine to 8mb. thanks, Tom
Re: [emax] Emax2 Memory Files
2016-01-28 by tonykirby100@...
Just to clarify my Emax 2 does not have a hard drive fitted. I have a brand new hard drive for it but never installed it due to the noise it generates. Yes
Re: [emax] Emax2 Memory Files
2016-01-28 by Ted Summers
I wonder if you got to the 8MB point and then did a copy software to floppy. boot from floppy (verify 8M) and wrote that to the hard disk, if that would save
Re: [emax] Emax2 Memory Files
2016-01-28 by Gary Doty
Tony, I believe it could be possible, a configuration back up may also be stored in the os if you booted from the hard drive Sent from Yahoo Mail on
Re: [emax] Emax2 Memory Files
2016-01-28 by tonykirby100@...
Hi all, I have a 4MB Emax 2 and bought the ram chips to install. It appeared that I had all the PALs as I had the expansion board already running at 4MB
Re: [emax] Emax2 Memory Files
2016-01-27 by Ted Summers
Per page 2- It looks like since you have 4MB you don’t need any PALs, just the scrambled megs or an eeprom programmed with 8MB stereo already detected to add
Re: [emax] Emax2 Memory Files
2016-01-27 by schtom83318@...
The PALs I have are: IP431AEMU3593 in IC54 IP432AEMU4393 in IC55 IP433AEMU4193 in IC56 IP430AEMU2294 in IC57 thanks, Tom
Re: [emax] Emax2 Memory Files
2016-01-27 by schtom83318@...
Sorry, I got digging again. So I have on the CPU board 16 P21014-08 k114A chips and 4 KM41C464P-8 chips. These are 18 pin chips. There are also 32 empty 20
Re: [emax] Emax2 Memory Files
2016-01-27 by schtom83318@...
Great. Thanks.
Re: [emax] Emax2 Memory Files
2016-01-27 by Ted Summers
Tom- I would suggest first that you verify the PALs that are available in the file (and looking at the guide, and the PALs currently installed on your board)
Re: [emax] Emax2 Memory Files
2016-01-27 by schtom83318@...
Awesome. Thanks for the clarification. So I ll look at getting some memory chips and then I look into figuring out how to make the pals with your post. I
Re: [emax] Emax2 Memory Files
2016-01-26 by Ted Summers
I think you misunderstand what Scrambled Megs IS. Scrambled Megs was specifically made available for the purpose of if the Emax 2 LOST it’s memory config,
Re: [emax] Re: Emax2 Memory Files
2016-01-26 by schtom83318@...
No I appreciate your help. So what happened to the Scrambled Megs way of upgrading with a code or is it better to put the chips in that you have made. I
Re: [emax] Re: Emax2 Memory Files
2016-01-26 by Ted Summers
It would be best to get all the same brand and part chips if possible…. On Jan 26, 2016, at 12:54 PM, schtom83318@yahoo.com [emax]
Re: [emax] Re: Emax2 Memory Files
2016-01-26 by Ted Summers
IF it’s a semiconductor reseller, you may want to contact them off the auction, as you need a large quantity, and that can lower the price. But I assume you
Re: [emax] Re: Emax2 Memory Files
2016-01-26 by schtom83318@...
Yeah mine are showing the -8. I see them on eBay and alibaba. So those chips don t matter except for the speed being the same?
Re: [emax] Re: Emax2 Memory Files
2016-01-26 by Ted Summers
Please look in the archive. I posted this explanation just within the last couple of days. As to the RAM- The -8 or -10 / -12 / -15 is the speed (80, 100, 120,
Re: [emax] EMAX penel
2016-01-26 by Ted Summers
It’s a form of vinyl. They have been using similar on arcade equipment for years and years. I don’t know if you have Kinkos print center in Deutschland,
Re: Emax2 Memory Files
2016-01-26 by schtom83318@...
I have an emax ii rack with 4mb and the expansion board. I have 32 empty slots. If I were to buy the 32 chips of KM41C464P-8 from alibaba or somewhere and
EMAX penel
2016-01-26 by w.niessen@...
Hello Everybody! Can someone tell me what kind of material is used for the EMAX panel?
Re: [emax] software reinstall
2016-01-26 by Ted Summers
I’ve never heard of this behavior due to an SE update. The SE update disk flips a couple of bits in the Parameter EEPROM ( this IC only holds settings like
software reinstall
2016-01-26 by england246@...
hi there i have a emax 1 was working perfcetly no issues . i bought an se upgrade disk installed it . since then nothing works as you turn sampler on seuencer
Re: [emax] Emax 2 Memory PAL files posted to the group.
2016-01-25 by Ted Summers
You don’t have any expansion boards to be populated. They plug on top of the blue connectors on the corner of the board. So having different PALs won’t
Re: [emax] Emax 2 Memory PAL files posted to the group.
2016-01-25 by Carl Simms
Http://imgur.com/a/LAqMQ No expansion nut from what i can make out i have several rows of unpolated sockets. So im not sure if yhoses pdfs apply to my
Re: [emax] Emax 2 Memory PAL files posted to the group.
2016-01-25 by Carl Simms
imgur.com/a/LAqMQ Heres a few pics of my 2mb stereo rack Sent from Yahoo Mail on Android On Mon, 25 Jan, 2016 at 2:04, Gary Doty djrgary@yahoo.com
Re: [emax] Emax 2 Memory PAL files posted to the group.
2016-01-25 by Ted Summers
Looking at the guide 1) you already need to have an expansion board 2216. Where that is the case, you would already have IP436 / IP438 as applicable (mentioned
Re: [emax] Emax 2 Memory PAL files posted to the group.
2016-01-25 by Gary Doty
The EmaxII memory retrofit instructions in the files section may provide further insight. I have so far not seen any 1 meg units. There were 2 different
Re: [emax] Emax 2 Memory PAL files posted to the group.
2016-01-25 by Ted Summers
Carl- I am not unwilling to make some ICs for you, I just can’t guarantee it will work out. I also don’t want to make a set of 6 chips and charge for 6
Re: [emax] Emu emax1 with problem in the input sampler
2016-01-25 by Matt Ferrari
You might not have the threshold level set low enough to detect a signal on the emax II its choice number 5 on the sample menu also there is a gain choice #1
Re: [emax] Emu emax1 with problem in the input sampler
2016-01-24 by Ted Summers
Did you go through the manuals / guides and do: calibration Emax Clinic Diagnostics Is that the only feature not working, or perhaps more than that? -T On Jan
Re: [emax] Emax 2 Memory PAL files posted to the group.
2016-01-24 by Carl Simms
I can act as a guineepig if anyone wisjesto make these files into kits. I currently have 2mb stereo but my motherboard has many empty ram slots. From what i
Emu emax1 with problem in the input sampler
2016-01-24 by yusteromerooscar@...
Recently I bought a Emu emax1 and I have a problem with the input sampler, it is not detecting input signal and (of course) no record... any clue of what is
Re: Emax2 Memory Files
2016-01-19 by Ted Summers
Graham- I’m sharing this out to a wider audience so I don’t have to type this out again- hope that’s ok. There is a file out there (I think Dave Sotnick
Re: [emax] how to read emax ez2 file ?
2016-01-19 by Ted Summers
.EZ1 = EMAX1 HARD DISK IMAGE .EZ2 = EMAX2 HARD DISK IMAGE These are for use in EMXP (free, on the internet- just google to find) to read and write a Hard Disk
how to read emax ez2 file ?
2016-01-19 by fainardi83@...
hello all i have download 3 file for my emax II these file have the ez2 extension how can i extract them to put on the sd or how can i convert them to hfe file
Emax 2 Memory PAL files posted to the group.
2016-01-19 by Ted Summers
I know this is a long time coming, as I mentioned this months ago… but here we are. First I would like to thank: Steve Klein - who through his persistence
New file uploaded to emax
2016-01-19 by emax@yahoogroups.com
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the emax group. File : /EMAX2MEM.zip
Re: [emax] How to update banks created with other operating system?
2016-01-19 by anunesyes@...
I don t have words for this. Thank you very much. You are awesome.
MUST disk complete
2016-01-18 by anunesyes@...
Hello all, Anyone has a M.U.S.T. disk complete? I want to make a test with the presets has diagnostics says and I think the MUST file is not complete. I am
Re: [emax] How to update banks created with other operating system?
2016-01-16 by Ted Summers
None of the factory images I created are saved with SE1.1, they are PLUS 1.0 (which requires your Emax has SCSI) BUT - you could still use EMXP to EXTRACT all
Re: [emax] How to update banks created with other operating system?
2016-01-16 by synthbay@...
Ted, I was reading through this topic because I too am trying to navigate through the process of preparing disk files for my HxC emulator-- which I m finding
Re: [emax] Jammie Logan ?
2016-01-08 by allan.michie@...
Hi Guys, Thanks for your feedback, happy to hear that you managed to get things sorted with him. I have his email and phone numbers but no replies since 6
Re: [emax] Jammie Logan ?
2016-01-07 by krikor kouchian
Hi, Yes he got back to me after some time and refunded me the PSU. Best K Le jeudi 7 janvier 2016, LIFELIKE laurent_ash@yahoo.com [emax]
Re: [emax] Jammie Logan ?
2016-01-07 by LIFELIKE
Hi I can testify despite taking time and not really fixing my psu problem he did reply to my emails and excused himself for being late and sent me the psu
Re: Jammie Logan ?
2016-01-07 by allan.michie@...
Hi Julien, Did you eventually get what you wanted from Jammie? He has done the same to me! I sent him in June 2015 an Emax Main Board for SCSI upgrade and slim
JM-215A available at the link if you need them
2016-01-07 by Ted Summers
http://www.orbitmicro.com/global/fd-adapter-1-p-5710.html -T [Non-text portions of this message
Re: [emax] buttons unreliable // JM215A
2016-01-07 by last7minute@...
Hello, Sorry if I m messaging incorrectly for the chance to ask if you, or anyone has any of the JM215A adapters available. Thank you, Chris Cieszkowski
Re: Slim floppy and cf card reader?
2016-01-07 by last7minute@...
Hello, Are the JM215As still available? Thank you, Chris Cieszkowski