Re: So I found the Reset Adjuster
2005-12-30 by gil_we
Is the battery fresh ? ... so
Messages
Browse messages
Page 91 of 114 · 5658 messages matched
So I found the Reset Adjuster
2005-12-30 by motionsandwaves
Turned it counter clockwise and the lights all lit up , adjusted it so it wasn t edgy. After 20 minutes or so it still reverts back to Bank A, Sound 1. Any
Re: [PolySix] Back to One
2005-12-30 by The Old Crow
It is labeled VR1 RESET and is located near the upper right-hand corner of the KLM-367 when looking at the board mounted in the Polysix. The other six trimmers
Reset Trimmer
2005-12-29 by modulatio@aol.com
... From: Modulatio To: PolySix@yahoogroups.com Sent: Tue, 27 Dec 2005 16:01:45 -0500 Subject: Re: [PolySix] Back to One ... From: modulatio@aol.com To:
SYNC DRUMSTATION (TR-909/808 DIN) --> ARP POLYSIX
2005-12-29 by russkie100
Hi there, Do you think it`s possible to sync a drumstation, with a Tr-909/Tr-808 din , to a polysix`s ARP ?? That Would be nice as i`m getting a drumstation
Re: [PolySix] Re: Just bought the polysix and have some questions
2005-12-28 by Chromatest J. Pantsmaker
... Most likely, NO. Most MIDI kits only record note-on/note-off, but there are some other expensive ones (if you can find them) that will interface more
Re: Just bought the polysix and have some questions
2005-12-28 by gil_we
I think Johannes is the best one to answer this ;) BTW Johannes, the uA726HC is on the way, we ll see what comes up :) Thanks. ... options
Re: Just bought the polysix and have some questions
2005-12-28 by russkie100
Responses are welcome :)
Re: [PolySix] Back to One
2005-12-27 by modulatio@aol.com
... From: modulatio@aol.com To: PolySix@yahoogroups.com Sent: Tue, 27 Dec 2005 09:35:13 -0500 Subject: Re: [PolySix] Back to One Might want to adjust the reset
Re: [PolySix] Back to One
2005-12-27 by modulatio@aol.com
A thousand thankyous , I ll let you know how it turns out. Cheers joe ... From: The Old Crow To: PolySix@yahoogroups.com Sent: Fri, 23
Happy XMAS to all from de-voir
2005-12-24 by kissthebats
Have a happy holiday New e.p. out now tilted something to live for Available on TARGET.COM now http://www.myspace.com/devoir
Re: [PolySix] Back to One
2005-12-23 by The Old Crow
That sounds like the KLM-367 is resetting. Might want to adjust the reset trimmer a little. The A-D, 1-8 LEDs (and other LEDs) should all light up for about
Back to One
2005-12-22 by motionsandwaves
I just recently had the battery replaced in my Polysix and had everything cleaned inside and out, the problem is that say if I m one Bank C sound 2, after
Just bought the polysix and have some questions
2005-12-21 by russkie100
I`m thinking of upgrading the polysix to midi. (Johannes) 1)Will i be able to record sutoff/resonance etc.. changes to a sequencer say cubase sx? 2)I`m not
Re: Anyone in/near Toronto, Canada able to replace my battery
2005-12-18 by gil_we
I really recommend doing that asap as it sounds like the battery is starting to leak. Very soon it can go on and damage the entire board. Replacing it VERY
Re: Anyone in/near Toronto, Canada able to replace my battery
2005-12-18 by toerag_man
By not too bad I mean there is the beginnings of some crud on the battery and some slight discolouration on the board near the battery. However, it isn t
Re: Anyone in/near Toronto, Canada able to replace my battery
2005-12-18 by gil_we
What do you mean by too bad ? Either it has leaked and prossibly caused damage or not. It doesn t have to affext the noise floor. I think just about any
Anyone in/near Toronto, Canada able to replace my battery
2005-12-17 by toerag_man
Hi, I just grabbed a Polysix from eBay. Sounds fabulous, although there is a pretty significant noise/interference problem. I opened it to find the blue
Re: Polysix no sound => good sound
2005-12-15 by hansomchaam
Hello, After fixing the battry problem there was still no sound so I got into complex research. Thanks to Johannes Hausensteiner who helped me step by step by
Re: Polysix no sound
2005-12-14 by gil_we
The 4xxx are very cheap to get, I d personally replace any suspective one, be careful with the unsoldering process ... ic5 ... ... effect
Re: Polysix no sound
2005-12-14 by Gregor Quade
I found out the 4556D on the panel board (369) is an oamp for the volume..Gil said those get down often..so check this one.. Hope it might help. Gregor
Re: Polysix wiered behaviour
2005-12-14 by Gregor Quade
Hi all, there are three IC on the panel boards (369 and 370) one 4556D which is an oamp as i found out this one is for the volume knob i think...and two 14051.
Re: Polysix wiered behaviour
2005-12-13 by gil_we
The 4xxx IC family tends to go bad when old ... seem to ... for ... board ... did, ... got ... the ... by the ... a ... technician ... recorder ...
Re: Polysix wiered behaviour
2005-12-12 by Gregor Quade
Thanks alot Gil, I already checked all the traces on the board which might got affected by the batteryleak. So far they are all working fine. The Tip with the
A freind's Polysix - VR2, VR1, D#4-E4 doesn't work properly
2005-12-12 by gil_we
I wonder if anyone would have any idea about the following problem... It s a friend s Polysix we both recovered from battery leakage a year ago, and left it
Re: Polysix wiered behaviour
2005-12-12 by gil_we
... Make sure it didn t experienced any battery leakage. You can look for green rust on the PBCs and the components on both the computer board and the one that
Re: Polysix weird behaviour
2005-12-12 by Gregor Quade
Hi all, Tested the CPU on TP4 get pulse of 10ms width..?? I also tested the signals on TP2 / TP3(GND) and i get corresponding changes for all the knobs except
Re: [PolySix] Re: Polysix wiered behaviour
2005-12-11 by u3dreal@yahoo.de
Hm I cleaned up all the trimpots.... I rather would like to know which IC could be wrong thanks a lot for reply.... Gregor Are you refering to the
Re: Polysix wiered behaviour
2005-12-11 by gil_we
Are you refering to the trimpot on the computer board ? I don t know very much about it but on my Trident it did the same when I set it to a cetrain position.
Polysix wiered behaviour
2005-12-11 by u3dreal
Hello all; I bought a polysix in rather bad condition... I did the batteryreplacements and checked to circuits...they seem to be OK for both sides of teh PCB
Re: Polysix no sound
2005-12-10 by hansomchaam
Hi, Great!! That s good information, I ll do the tests with my scope and let you know, thanks, Han. ... 20msec. ... of ... you see ... (green ... contacts ...
Re: [PolySix] Re: Polysix no sound
2005-12-10 by Johannes Hausensteiner
Hi, I do not want to discouorage you, but I do not believe that it is the KLM-367 s CPU. This does only the programmer. You can check it very easily: 1) If
Re: Polysix no sound
2005-12-10 by gil_we
I think it is a standard part for simple diy circuits, the ones students usually build. You should be able to find it at a local electronics shop I think ...
Re: Polysix no sound
2005-12-10 by hansomchaam
Hello, Every suggestion from everyone given to me (thanks) I have tried but still no sound. The problem seems to be in the 8048 processor on KLM367. The
Re: Trident MKII - one oscillator is out of tune
2005-12-09 by gil_we
Now I got the feeling the the multitransistor has gone defected... I let the machine work all night long, and when I check it out the dualtransistor is not hot
Re: Trident MKII - one oscillator is out of tune
2005-12-09 by gil_we
Now I see what happened... I guess that was a big mistake using the freeze spray on such a sensitive circuit. The problem is that I already even readjusted
Re: [PolySix] Re: Trident MKII - one oscillator is out of tune
2005-12-08 by Johannes Hausensteiner
The multileg component probably is the dual transistor for the antilog amplifier. This is one of the most critical stages in terms of note frequency. It
Re: Trident MKII - one oscillator is out of tune
2005-12-07 by gil_we
ooops... the multileg component is IC6, not R40 ... machine ... gap ... tuning ... looking ... tune ... common ... Rx39 ... nominal ... it ... the ... the ...
Re: Trident MKII - one oscillator is out of tune
2005-12-07 by gil_we
Thanks guys ! There was something strange going on.... After writing my previous mail I ran over a few components with a freeze spray, among them the
Re: [PolySix] Re: Trident MKII - one oscillator is out of tune
2005-12-07 by Chromatest J. Pantsmaker
replace them again? Sometimes (and it will always bite you) you put in a bunk part as a replacement.. then you spend all week looking for something else,
Re: [PolySix] Re: Trident MKII - one oscillator is out of tune
2005-12-06 by Johannes Hausensteiner
If it is only one VCO, then things are different. It may be the cap (C709), which I do not believe because it is a polypropylene type, which have very good
Re: [PolySix] Re: Trident MKII - one oscillator is out of tune
2005-12-06 by Johannes Hausensteiner
1) If you experience that one voice has this problem, and within this one voice it is both VCOs then it is very likely that the reason lies in a component or
Re: Trident MKII - one oscillator is out of tune
2005-12-06 by gil_we
You know what ?... now I relaize I replaced IC8 and ICx11 as well ! What if the problem is related with only one of the VCOs...? lets say VCO1. What would you
Re: Polysix no sound
2005-12-06 by hansomchaam
Hello, Still no sound, every chip has his power, setup from tape seems to work correctly (bank 1..8 lit up) so I think the problem is somewher on KLM366 (new
RE: [PolySix] Re: Polysix no sound
2005-12-06 by FRANK SPANO
Thanks, I ll try that ... _________________________________________________________________ Is your PC infected? Get a FREE online computer virus scan from
Re: [PolySix] Re: Trident MKII - one oscillator is out of tune
2005-12-06 by Johannes Hausensteiner
If you already replaced Rx39/Cx10 then the only thing in common for both VCOs in one voice is ICx11 (TL072). THe value of Rx39 is not very critical unless it
Re: Polysix no sound
2005-12-06 by lnz2166
This might sound trivial but is your power supply output all in check. In addition have you checked the the solder pads on the power connectors. I had and
Re: Trident MKII - one oscillator is out of tune
2005-12-06 by gil_we
Thanks ! The Cx10 and Rx39 have been already replaced to no avail. By IC8 are you refering to ICx08 ? it s a 4558 opamp. btw, I now see that I had to replace
RE: [PolySix] Re: Polysix no sound
2005-12-05 by FRANK SPANO
I have a similar problem. Does anyone have a scanned service manual I can get emailed? Greatly appreciated ...
Re: [PolySix] Re: Trident MKII - one oscillator is out of tune
2005-12-05 by Johannes Hausensteiner
Hi, The caps are Cx10 ... where x is the voice number. On the schematics only voice #7 is drawn in detail, so you can see C710. Maybe it is not the cap but the