Re: Epson R1800 to good home
2014-09-05 by paulmwhiting@...
As to film grain adding to the perception of sharpness... seems to me I recall some preferred using D-76 straight, undiluted, for that reason. I think they
Messages
Browse messages
Page 42 of 2186 · 109257 messages matched
Re: [Digital BW] Re: Epson R1800 to good home
2014-09-04 by Paul Roark
... I think for many subjects that is true. I ve always wanted a 1.5 picoliter 24 inch wide Epson printer that would allow it at larger display sizes. One
Ink carts 3880
2014-09-04 by ann clancy
Recently bought a set of ink for my 3800 printer didn t realize that the magenta carts will not fit the 3800 but go into a 3880 $90 for both ( that is
Re: Epson R1800 to good home
2014-09-04 by paulmwhiting@...
Harlan, I agree with you about that pop ! See my reply to Paul Roark. Am getting my 1400 curves fine-tuned however and they re looking very good. A friend of
Re: Epson R1800 to good home
2014-09-04 by paulmwhiting@...
Paul, After a lot of research, and some helpful message exchanges in this group and elsewhere, I finally came to some understanding on what was causing those
Re: Epson R1800 to good home
2014-09-04 by Harlan Chapman
Hello Paulm, BO prints from the R1800 running 3MK are my favorite inkjet BW prints. They don t look good through a magnifier, but up on the wall they have pop
Re: [Digital BW] Re: Epson R1800 to good home
2014-09-04 by Paul Roark
My 1800 bit the dust quite a while ago. Paul, what was the cleaning cart that developed the clog? Eb6 in the 1400 is usually clog free -- a combination of a
Re: Epson R1800 to good home
2014-09-03 by paulmwhiting@...
Harlan, I found your post very interesting... I was in the same predicament a few months ago, finally put my R1800 on the local Craigs List, free. I felt bad
Epson R1800 to good home
2014-09-02 by hchapman@...
I have an Epson R1800 set up for 3MK printing that I d like to give away. Includes MIS inks, refillable cartridges, chips, chip resetters. Non-used heads have
Re: Source for Refillable Cartridges
2014-08-26 by vsr98@...
Thanks Lincoln. Your suggestion to unplug the printer helped. All the cartridges are recognized but the ink level monitoring doesn t work. At least I can
Re: Source for Refillable Cartridges
2014-08-19 by paulmwhiting@...
Thanks for the tip, Michael, but I tried that... it s as if all the spaces were somehow eliminated. You can see that happening throughout the post. Maybe it s
Re: Source for Refillable Cartridges
2014-08-18 by Michael-K
Paul, if you put the link on it s own line I think your problems will disappear.
Re: Source for Refillable Cartridges
2014-08-17 by paulmwhiting@...
My buried link worked after all, and it worked for me as well! Still, I do appreciate your tip on surrounding the link with . I ll try that next time
Re: [Digital BW] Re: Source for Refillable Cartridges
2014-08-17 by Sam McCandless
As I hope we will be able to see in this response of mine to Paul (WhitingÆs) posts, his rendition of the link still looks truncated. But it worked for me in
Re: Source for Refillable Cartridges
2014-08-17 by paulmwhiting@...
I m having trouble making that link stand apart from the text. The link ends with a dot f and my following text is right next to that... I can t seem to make
Re: Source for Refillable Cartridges
2014-08-17 by paulmwhiting@...
I feel a bit of a traitor for saying this, but I ended up with Jon Cone s carts. I had to return the MIS arts twice before I got a set that was recognized. I
Re: Source for Refillable Cartridges
2014-08-17 by jacques.caron@...
Same thing here. The first insertion was OK. At my first refilling, I had to fill, start, stop and reinsert the cartridges. Now, from time to time, the printer
Re: Source for Refillable Cartridges
2014-08-17 by Lincoln Fajardo
For the 1430 Inkjetmall cartridges that I m using, it is a matter of taking them out and re-inserting. May require unplugging the printer for this process. I
Source for Refillable Cartridges
2014-08-16 by vsr98@...
I ordered a set of refillable cartridges along with Eboni 6 inks for my Epson 1430, from inksupply.com. Unfortunately, they don t work very well. Some of them
Re: Refilling and syringes/needles, etc.
2014-08-16 by vsr98@...
Thanks to all who replied. Vijay
Re: [Digital BW] Refilling and syringes/needles, etc.
2014-08-16 by vsr98@...
Thanks Paul.
Re: [Digital BW] QTR
2014-08-12 by Truman Prevatt
I just ordered and received some Silver Rag from Museo. I thought I would try it since there was a profile in QTR. I must say that has become my favorite
Re: Refilling and syringes/needles, etc.
2014-08-12 by Bill Lewis
I have been refilling for 20 years I still have some syringes that are around 10 years old for using with my all in ones. When I bought my wife the Canon 9500
Re: [Digital BW] QTR
2014-08-12 by Leopold Green
I d be really interested in any comments on this too... thanks Leopold
Re: Refilling and syringes/needles, etc.
2014-08-11 by jacques.caron@...
Hi That s a good thing to know. I bought mine with the full kit more than a year ago and , after a lot of refilling, it seems that I will replace the
Re: Refilling and syringes/needles, etc.
2014-08-11 by Myron Gochnauer
In Canada, the best places to buy syringes for refilling cartridges are (farm) animal feed and supply stores. I buy 60ml syringes and needles, and then grind
Re: Refilling and syringes/needles, etc.
2014-08-10 by Seth Rossman
Rinse and air dry. If you are using them daily, have two sets. Cheaper on Amazon too. -- If I agreed with you both of us would be wrong.
Re: [Digital BW] Refilling and syringes/needles, etc.
2014-08-10 by Paul Roark
I rinse the refilling accessories and let them air dry. I use a bulb blower to blow the water out of syringe needles and bottom fill adapters. Eventually the
Refilling and syringes/needles, etc.
2014-08-09 by vsr98@...
First, a thank you to Paul Roark for his detailed descriptions and instructions regarding Eboni 6. I started with pre-filled ink cartridges from inksupply.com
Re: [Digital BW] Epson 1430 with Eboni6 - solarization and misaligned print heads?
2014-08-09 by jacques.caron@...
Hi I had this problem once and if I remember well this was cause by cross-over inks. I tried to print the same image with two different profiles from Photoshop
Re: [Digital BW] Epson 1430 with Eboni6 - solarization and misaligned print heads?
2014-08-08 by Paul Roark
If you have a Calibration Mode print from when the printer was working well, print one now and see if one ink position is not working as intended. If one
Epson 1430 with Eboni6 - solarization and misaligned print heads?
2014-08-08 by climballday@...
Hi gang, Details of the system: Mac OS 10.8.5 software Photoshop CS6 Quadtone Rip Eboni 6 Inks Epson Artisan 1430 printer. So about a week ago, I was printing
Re: QTR
2014-08-03 by zonepeter@...
Don t know about the R3000, but typically there are profiles for Silver Rag 1 or 2 other of the baratya papers. I have had good luck using those as starting
QTR
2014-08-03 by Truman Prevatt
I just downloaded and installed QTR to use on my Epson R3000 on my Mac. I would like to use it on Harman Gloss Baryta. However, I don t see a profile that
Re: [Digital BW] Storing an Epson printer
2014-07-29 by hrblaine@...
You guys are all nuts. Stick the damn thing in a box.
Re: [Digital BW] Storing an Epson printer
2014-07-29 by Paul Roark
Use generic base C6B. Paul www.PaulRoark.com On Tue, Jul 29, 2014 at 11:20 AM, Globe Trotteur unglobetrotteur@hotmail.com [DigitalBlackandWhiteThePrint]
RE: [Digital BW] Storing an Epson printer
2014-07-29 by Globe Trotteur
Sorry paul if i am being a numb nut but after reading your pdf, it says that the c6a is for all printers except the 1400 and 1800. Should i be buying that
Re: [Digital BW] Storing an Epson printer
2014-07-29 by Paul Roark
I use C6B for all but Arches and 1.5 pl printers. Edwal LFN (the additional ingredient in B) is an excellent cleaner. Usually 2 head cleanings purges the old
RE: [Digital BW] Storing an Epson printer
2014-07-29 by Globe Trotteur
Thanks Paul. Should i get the c6a or c6b? I have a R2400. It looks like the c6b would be the one.After i put that in my empty cartridges, how many head
Re: [Digital BW] Storing an Epson printer
2014-07-29 by Paul Roark
I don t have any information on Worm water. It sounds like the generic base. Paul On Tue, Jul 29, 2014 at 5:20 AM, Globe Trotteur unglobetrotteur@hotmail.com
RE: [Digital BW] Storing an Epson printer
2014-07-29 by Globe Trotteur
Thank you paul. I found this product that is not really a cleaning fluid. It is more it looks like to be used when you swap
Re: [Digital BW] Storing an Epson printer
2014-07-28 by Paul Roark
In addition to cleaning fluid in the carts, you might want to rinse off the parking pad with some cleaning fluid. When you go to change the inks, pull the
Storing an Epson printer
2014-07-28 by Globe Trotteur
I am sure this question may have been asked quite a few times. I just got an Epson r2400 that I am going to keep as a spare to replace my 2200 in vase it dies.
Re: [Digital BW] Green stuff in my brown prints
2014-07-26 by Leslie Otterbein
Hi David: Have you tried the print alignment utility? If your colours are out of register there may be colour changes from one end to another. This is what
Re: Workflow assistance?
2014-07-26 by michael3442@...
I ve now cleaned up the files I had uploaded to Dropbox so all but one (.psd format with layers included) will open in preview; they all download and open in
Re: [Digital BW] Re: Workflow assistance?
2014-07-26 by mrjimbo2
Elliot, In theory much of it should.... but in function you don t have the ability to make image adjustment or selections using color.. So you just will have
Re: [Digital BW] Re: Workflow assistance?
2014-07-26 by mrjimbo2
As far as tree tips and making masks.. Their are many tricks to making selection masks to capture finer detail.. Here s one for you.. Before you put any
RE: [Digital BW] Re: Workflow assistance?
2014-07-26 by Elliot Puritz
For those of us who are new to digital photography, and thus learning how to use PS and other editing programs, the information about masking is both
Re: Workflow assistance?
2014-07-26 by michael3442@...
Paul, great info. thanks for taking the time to share your expertise. I ve already printed it out knowing I ll be referring to it many times before it sinks
Re: [Digital BW] Re: Workflow assistance?
2014-07-26 by mrjimbo2
Just a few more words here.. in an effort to make it hopefully more logical.. First a scanner has to be dialed in to respond to a certain film type correctly..