Re: [korgpolyex] Re: Chord mode and MIDI
2019-04-08 by alexis.ouelhadj@...
Thanks Mike. I ll try to save it via tape then, hopefully it will work :) first time doing this. Cheers and thx again
Messages
Browse messages
Page 3 of 141 · 7050 messages matched
Re: [korgpolyex] Re: Chord mode and MIDI
2019-04-08 by support
When you do a patch tape dump, it also saves the sequencer data AND the chord progression. Same thing with the EX and MK2 sysex dumps, they also save and load
Re: Chord mode and MIDI
2019-04-07 by alexis.ouelhadj@...
Thanks for your response ! I ve looked at the manual and couldn t find a way to record the chord progression via Tape. I have the Poly 800 version, not the Mk2
Re: [korgpolyex] Re: Chord mode and MIDI
2019-04-07 by alexis.ouelhadj@...
Thanks for your response ! I ve looked at the manual and couldn t find a way to record the chord progression via Tape. I have the Poly 800 version, not the Mk2
Re: [korgpolyex] Re: Chord mode and MIDI
2019-04-07 by support
You can save a chord progression to tape (PS-800) or to MIDI (PS800-II and EX800). Which is awful but it works. Only the single note that is held down is sent
Re: Chord mode and MIDI
2019-04-07 by alexis.ouelhadj@...
Hi everyone, I wanted to follow up on this old topic. I ve saved a chord from random notes that sounds pretty well, and I wouldn t want to lose it! Thing is, I
Re: [korgpolyex] Re: Install issues and possible further queries
2019-04-06 by pizzicato2007@...
Thanks Mike, I will definitely be looking into this today. I ll take another set of pictures and send em along soon.
Re: [korgpolyex] Re: Install issues and possible further queries
2019-04-06 by support
I believe you might need to check that the capacitors underneath the AtomaHawk board are bent over so that they do not come into contact with the Atomahawk.
Re: [korgpolyex] Re: Install issues and possible further queries
2019-04-01 by pizzicato2007@...
No real rush, I am having a second set of eyes go over it with me this weekend, so I can actually learn to solder better as well.
Re: [korgpolyex] Re: Install issues and possible further queries
2019-04-01 by support
I am pretty busy this week. But I ll do my best to review the pictures and offer some comments as soon as I can. /Mike On Mon, 2019-04-01 at 00:11 +0000,
Re: [korgpolyex] Re: Install issues and possible further queries
2019-04-01 by pizzicato2007@...
Small edit- I can t hear the oscillator, only the noise I previously mentioned.
Re: [korgpolyex] Re: Install issues and possible further queries
2019-04-01 by pizzicato2007@...
OK, so I tried submitting stuff on Friday, but I don t know if it loaded (tried to upload eleven pics). So here is try #5? Here s the attachments of the
Re: [korgpolyex] Lost contact?
2019-03-23 by bperkins211@...
OK. TTYL..
Re: [korgpolyex] Lost contact?
2019-03-23 by support
Hi Blaine, I got your earlier email, I just didn t get a chance to give it a good response. I ll email you separately over the next week or two. Nice work!
Lost contact?
2019-03-23 by bperkins211@...
Hey Mike, I tried emailing your support@hawk800.com a few times and have not heard any replies. Not sure if you are not receiving them or some other reason I
Re: [korgpolyex] Re: Install issues and possible further queries
2019-03-18 by pizzicato2007@...
Hey all, sorry for the late response! Just to clarify I did load all of the patch banks, and the noise was still there, but I was able to salvage and edit one
Re: [korgpolyex] Re: Stucked in Flash Mode
2019-03-16 by support@...
Does that mean that you were able to install version 2.65 of the code too? Cheers from Connecticut! ... From: korgpolyex@yahoogroups.com To:
Re: Stucked in Flash Mode
2019-03-15 by damaandrea1@...
I ve managed to send the BOOT code via Midi, swapped the chips and now the synth is WORKING! Thanks for your help :) Cheers from Berlin
Re: [korgpolyex] Re: Install issues and possible further queries
2019-03-15 by support@...
You need to load patch banks or else most of the patches are going to sound terrible. Like synthetech said. I notice your first patch 11 has DCO harmonic
Re: [korgpolyex] Re: Stucked in Flash Mode
2019-03-15 by support@...
Put the original 28C256 back into the boot ROM socket and make sure that booting up you get into FLASH. Then we can keep trying. Did you swap the ROM s back?
Re: Install issues and possible further queries
2019-03-14 by Synthetech
If you haven t loaded up Banks 2,3 ,,& 4 yet, I would go ahead and do them too. May not make a bit of difference, but I think I recall I had to load all the
Re: Install issues and possible further queries
2019-03-14 by pizzicato2007@...
I did- in the first bank, those good patches (11 & 15) I was able to tame the sounds, and get some unique textures. I love the SLFOs. Everything else sounds
Re: Install issues and possible further queries
2019-03-14 by Synthetech
Did you load the default patches available for download? https://sourceforge.net/projects/hawk800/files/Patch%20Library/ I had issues getting my HAWK to sound
Re: Install issues and possible further queries
2019-03-14 by pizzicato2007@...
Awesome, thanks for that tip Here’s a couple links for audiovisual examples:
Re: [korgpolyex] Re: Stucked in Flash Mode
2019-03-14 by damaandrea1@...
Hello Mike, I m at a point now where I m stucked in ERROR 1 after trying to send the BOOT code to the poly. When I ve updated the software to 2.66 all the
Re: [korgpolyex] Re: Stucked in Flash Mode
2019-03-13 by support
One last thing... Be very, very careful when you do the boot code upgrade. You don t want to brick your Poly! Then you have to get a boot ROM from me. Less
Re: [korgpolyex] Re: Stucked in Flash Mode
2019-03-13 by damaandrea1@...
Ok I got it! Thanks for your help, I will update you on the result.
Re: [korgpolyex] Re: Stucked in Flash Mode
2019-03-13 by support
The ability to flash into your Poly either boot code or the software itself should work as long as your Poly can get into FLASH mode. If you want to get to
Re: Stucked in Flash Mode
2019-03-13 by damaandrea1@...
It seems there is no way to update the boot code at the moment. Since I ve tried to downgrade the software the synth is not able to receive Midi anymore. Setup
Re: Stucked in Flash Mode
2019-03-13 by damaandrea1@...
Could you explain me what is the right process to update the boot ROM code in this case? Thanks
Re: [korgpolyex] Re: Stucked in Flash Mode
2019-03-13 by support
Error 1 means you are sending invalid MIDI to the HAWK. Check your MIDI set up is not sending other MIDI and make sure there are no MIDI loops. Boot version
Re: Stucked in Flash Mode
2019-03-13 by damaandrea1@...
I ve tried to downgrade to v2.65l and to 2.59a but is not working, error 1 appears
Re: Stucked in Flash Mode
2019-03-13 by damaandrea1@...
Hey Mike thanks for your answer. B 1 .95 - F 2. 66 is what I see when I start up the Hawk holding the Bank Hold Button now. B19F26 appears when I go in Tools
Re: [korgpolyex] Re: Install issues and possible further queries
2019-03-13 by support
If you zero out most of the extended parameters and you still here distortion then you need to check the AtomaHawk hardware install. Especially, check the 10
Re: [korgpolyex] Re: Stucked in Flash Mode
2019-03-13 by support
Does your boot up show B19F26? If that is what you see when you start up your HAWK while holding down the bank hold button, then you don t have the latest boot
Re: Install issues and possible further queries
2019-03-13 by pizzicato2007@...
I think I am getting a lot closer in fixing up the patches, thanks for all the help thus far Mike!! But I do have more questions/ guidance/ suggestions- So I
Re: Stucked in Flash Mode
2019-03-13 by damaandrea1@...
Software Version B19F26
Stucked in Flash Mode
2019-03-13 by damaandrea1@...
Hello everyone, I have a problem with my Korg poly 800/Hawk800. I ve updated the software to the 2.66 verison, all the procedure went fine but now is stucked
Re: Install issues and possible further queries
2019-03-12 by pizzicato2007@...
Cool, I got this late so I’ll look and check if everything is zeroed out after work.
Re: [korgpolyex] Re: Install issues and possible further queries
2019-03-12 by support
The resistors need to be in the right locations. But if the resistor bands are reversed in their correct positions, that doesn t matter. Set all extended
Re: Install issues and possible further queries
2019-03-12 by pizzicato2007@...
Disregard the last part.
Re: Install issues and possible further queries
2019-03-12 by pizzicato2007@...
Ok, so my global 58 was set to 1, there’s still so much noise, it didn’t fix much, there was improvement when I just played with the presets, but there was
Re: Install issues and possible further queries
2019-03-11 by pizzicato2007@...
Also oops sorry, I keep getting extended parameters and global confused. I get it now.
Re: Install issues and possible further queries
2019-03-11 by pizzicato2007@...
This makes plenty of sense! Well, I’ll be going in on it after work. Wish me luck. I’ll reply on this thread once I’m done or have other issues.
Re: [korgpolyex] Install issues and possible further queries
2019-03-11 by support@...
Yes, you will have to go through the process again. Because the process writes the boot code into the software ROM. Then you swap the software ROM (which has
Re: [korgpolyex] Install issues and possible further queries
2019-03-11 by pizzicato2007@...
Hey Mike, Extended parameter 58 is set to 1, but I’ll check again if I am doing it correctly. Thanks for the bottom octave tip, I’ll check to make sure it
Re: [korgpolyex] Install issues and possible further queries
2019-03-11 by support@...
Hi John, 1) error 3 hasn’t gone away just yet, after installing the new boot ROM. however, I acknowledge I did skip a step and didn’t do the chip swap
Install issues and possible further queries
2019-03-11 by pizzicato2007@...
Hey there, New user, but I’ve been parlaying messages back and forth via email to Mike and the person building my Hawk 800/ Atomahawk mods over the past few
Re: [korgpolyex] Korg poly-800 dead display
2019-03-10 by studio_1a@...
Hi Mike, yes, I ve gone thru the troubleshooting procedure and circuit description also checked the waveforms. I do have CPU RES_7.5 waveform and much of the
Re: [korgpolyex] Korg poly-800 dead display
2019-03-10 by support
It may well be something else that is stopping the display from operating. Such as for example, the CPU bus lines, decoders, latched and supporting DTC s etc