Re: [korgpolyex] Re: korg poly 800 problems joystick and 12 db
2015-02-26 by Michael Hawkins
You need to describe to us what the joystick is or is not doing - both right and wrong. Then we can maybe help. /Mike From: Vincenzo Vincenzo
Messages
Browse messages
Page 19 of 141 · 7050 messages matched
Re: [korgpolyex] Re: korg poly 800 problems joystick and 12 db
2015-02-26 by Vincenzo Vincenzo
Hello Mike, okay, I found the .pdf file that you said to read .. I checked the board KLM-599 is ok, I think the problem is integrated on the motherboard
Re: [korgpolyex] Poly800 button issue and Atomahawk question
2015-02-26 by Vincenzo Vincenzo
Hello Rob, I advise you to check the cable connections and input pin, possibly clean with Flux for contacts eletttrici .. at worst you have to replace the
Re: [korgpolyex] Re: korg poly 800 problems joystick and 12 db
2015-02-26 by Vincenzo Vincenzo
Hello Mike, thanks for the response and the help, I tried to open the link you sent me but it does not open and gives me the following message: Error occurred
Re: [korgpolyex] Poly800 button issue and Atomahawk question
2015-02-25 by Michael Hawkins
You definitely a problem with the keyboard multiplexing circuit. Check out the schematics in the files section under Poly-800 - Servicing section You
Poly800 button issue and Atomahawk question
2015-02-25 by robertburnham23@...
Hello people I have recently purchased a Korg Poly800 from eBay but it has a few issues unfortunately. The main one that is troubling me is the 8 button does
Re: [korgpolyex] Re: korg poly 800 problems joystick and 12 db
2015-02-24 by Michael Hawkins
See this document
Re: korg poly 800 problems joystick and 12 db
2015-02-24 by sarvamala@...
hello everyone, I solved the problems 24/12 db .. the problem was due to defective switch that did not contact well .. Unfortunately I still have problems with
Re: [korgpolyex] Technical info on Poly800 & analog mods
2015-02-22 by Michael Hawkins
I am bit biased toward not putting the POTS in at all because with the AtomaHawk installed you have full MIDI control over everything. So a controller is all
Re: [korgpolyex] Technical info on Poly800 & analog mods
2015-02-22 by chillipower.uk@...
Hi Mike, thanks for the response. I think I ll wait now until Hawk/atomahawk at installed and working, but while I m in there I ll scope out the circuits for
korg poly 800 problems joystick and 12 db
2015-02-12 by Vincenzo Vincenzo
hello to all of grouplet, I wanted to ask for your help because I have a problem with my Korg Poly 800 modified Moog Slayer mod and cutting 12/24 db filter ..
NJM2069 Levels
2015-02-11 by ackolonges@...
Hi group, I m in the process of trying to build a VCF / VCA module around an NJM2069 chip pulled from a dead Poly-800. I m referring to the schematics in the
Re: [korgpolyex] Early Poly Memeory Battery Mod
2015-02-10 by burton_neal@...
Hi thanks for your response! That s my fault, I soldered the wrong wires on. I ll follow you instructions, you ve really helped me out there... Much
Help wanted!
2015-02-09 by Michael Hawkins
Hello HAWK and AtomaHawk fans, I need your help. I am revamping the HAWK-800 and AtomaHawk web pages. To do that, I would really thank you all for some
Re: [korgpolyex] Technical info on Poly800 & analog mods
2015-02-06 by Michael Hawkins
Check out the files section and you will find the schematics for the Poly. The LFO s are all software. But the control signals could be intercepted and set up
Technical info on Poly800 & analog mods
2015-02-06 by chillipower.uk@...
Hey group, Been interested in modifying particularly the analog side of a few old analog synths I have. Particularly with some CV in/out so they can modulate
Re: [korgpolyex] Early Poly Memeory Battery Mod
2015-02-03 by <backshall1@...>
Neal, It looks like you’ve got R1 and D1 cut out okay. The battery goes across the D1 pins. “FOUR” in your photo is where the positive (+) side of the
Early Poly Memeory Battery Mod
2015-02-03 by burton_neal@...
Hi guys! Love the group, great idea and really helpful. Was wondering if you could help me? Could you tell me exactly where i need to solder the positive and
Re: [korgpolyex] Re: Poly800 sometimes suffers from, verry low output volume / noisey output / only sound from right(left) output
2015-01-30 by Louis Botterill
Glad you made progress with your noisy pot. Good idea not to risk damaging the PCB, that would be bad. Yeah I might leave this MAX as-is, since after a clean
Re: [korgpolyex] Need Help Diagnosing a sick Poly
2015-01-30 by Michael Hawkins
When you press the write button, you have to enter the patch number that you want the current sounding patch to be written to. Pressing Write alone does not
Re: Poly800 sometimes suffers from, verry low output volume / noisey output / only sound from right(left) output
2015-01-29 by berendnie@...
Just took it out and let the pot part sit in isopropyl alcohol, i tried plumping al the solder off to take it off the board, but it took to long and i didn t
Re: Need Help Diagnosing a sick Poly
2015-01-29 by sread@...
That was it :)
Re: [korgpolyex] Re: Poly800 sometimes suffers from, verry low output volume / noisey output / only sound from right(left) output
2015-01-29 by Louis Botterill
Hi, I suspect if you re going to go as far as remove and disassemble the pot / fader you might as well replace it anyway, since you ve done all the work.
Re: Poly800 sometimes suffers from, verry low output volume / noisey output / only sound from right(left) output
2015-01-29 by berendnie@...
I like this video, kind of a comparison in differend ways of cleaning. Potentiometer Cleaning Showdown https://www.youtube.com/watch?v=8--qp_j-l40
Re: Some nice introspective musak!
2015-01-29 by chillipower.uk@...
Happy New Year to you too Mike. By the way, I love that music, I ve been listening to it quite a bit. Nice find, if only I could also get in on vinyl that
Re: [korgpolyex] Re: Need Help Diagnosing a sick Poly
2015-01-29 by Martin Ator
And you disabled the memory protect switch before trying to save the patch data? On Thursday, 29 January 2015, 17:40, sread@microsoft.com [korgpolyex]
Re: Need Help Diagnosing a sick Poly
2015-01-29 by sread@...
I should mention that this version of the mainboard does not have the dime sized battery. It only have the 6 C batteries.
Re: [korgpolyex] Need Help Diagnosing a sick Poly
2015-01-29 by sread@...
Here s an update: After checking the parameters for the factory patches, I noticed they were not correct. So I manually entered in patch 11 and low and behold
Re: [korgpolyex] Re: Poly800 sometimes suffers from, verry low output volume / noisey output / only sound from right(left) output
2015-01-29 by Louis Botterill
Well not sure where you are and what you can easily get hold of. I ve been using Servisol Super 10 which is like a de-facto switch cleaner and it works
Re: Poly800 sometimes suffers from, verry low output volume / noisey output / only sound from right(left) output
2015-01-29 by berendnie@...
HI Louis, Thank you, are you talking about deoxit? any type you can suggest ? It also makes crackling noises when turning the pot so i think the problem is
Re: [korgpolyex] Re: Poly800 sometimes suffers from, verry low output volume / noisey output / only sound from right(left) output
2015-01-28 by Louis Botterill
if you ve not already, you could try switch cleaner and checking around the pot for dry solder joints. I ve just resurrected a 32 year old Sequential MAX where
Re: Poly800 sometimes suffers from, verry low output volume / noisey output / only sound from right(left) output
2015-01-28 by berendnie@...
Alright, in the service manual i see its a 10k pot (VR with POWER SW) I guess any 10k stereo pot with on and off switch will do. Still if you have something to
Poly800 sometimes suffers from, verry low output volume / noisey output / only sound from right(left) output
2015-01-28 by berendnie@...
Hello everybody! I will try to be as brief as possible! My Poly800 sometimes suffers from a verry low output volume and or a noisey output and or only sound
Re: [korgpolyex] Need Help Diagnosing a sick Poly
2015-01-27 by Louis Botterill
Hi, mine does this currently (well it sounds like it s the same as yours). However the cause is basic (in my case), so please excuse me if I mention something
Re: [korgpolyex] Need Help Diagnosing a sick Poly
2015-01-27 by sread@...
Great questions. Thanks for the response. I can answer most of these. I did get a GOOD on the LCD after the Load (write was enabled) - although after going
Re: [korgpolyex] Need Help Diagnosing a sick Poly
2015-01-27 by Michael Hawkins
Did you get GOOD on the display after sending the default patches to Poly?Did you have program write switch set to enable ? Do all keypad functions work?
Need Help Diagnosing a sick Poly
2015-01-26 by sread@...
I recently bought a non working Poly 800 MK1. The previous owner said it made strange noises. I thought I could load the factory patches (like I have before)
Re: Some nice introspective musak!
2015-01-26 by domgoold@...
still here, Mike!!! ;-) happy new 2015 - you ve been hibernating, eh. few problems too many to deal with atm, concntrating on vital essentials (of which my
Some nice introspective musak!
2015-01-25 by Michael Hawkins
Well, it s 2015 and we as a small community of Poly lovers have been way too quiet here. I want to thank all of you for being on a parallel path of love and
Re: [korgpolyex] Re: Need help with an Atomahawk problem
2015-01-07 by Michael Hawkins
If the Poly comes up and runs and most other parameters and functions work OK then it would be unlikely to be the power. Are you saying that it worked but then
Re: [korgpolyex] Re: Need help with an Atomahawk problem
2015-01-06 by basecamp_88@...
Thanks for the input Mike. I tested it out today and everything seems to be working?! I double-checked the wiring and the board mounting for possible short
Re: [korgpolyex] Re: Need help with an Atomahawk problem
2015-01-05 by Michael Hawkins
Sounds to me like AtomaHawk is not working at all. Check your wiring. And also check that you have the ribbon cable headers in the correct orientation
Re: Need help with an Atomahawk problem
2015-01-05 by basecamp_88@...
Well the strange noise following the sounds is resolved. Still dealing with the programming issues of the atomahawk features: Moog slayer seems to be stuck in
Re: Need help with an Atomahawk problem
2015-01-01 by basecamp_88@...
Forgot to mention, this is an Atomahawk 1.3b board in an Mk1
Need help with an Atomahawk problem
2015-01-01 by basecamp_88@...
I m having a problem with the Atomahawk install that I just can t nail. Here s what I ve identified: Moog slayer seems to be stuck in an on state (P2 58 - 1)
Re: Testers wanted : Hawk 800 Max for Live editor
2014-12-22 by lists@...
Also Alex, and any other tests (Mike I know yours already), just send me your email so I can direct mail the binaries and instructions.
Re: Testers wanted : Hawk 800 Max for Live editor
2014-12-22 by lists@...
Hey Alex, I m not quite sure if you ll need Max 7 or not. You might have to download it and point Ableton s Max preferences to that version but you don t need
Re: [korgpolyex] Testers wanted : Hawk 800 Max for Live editor
2014-12-19 by Alex Drinkwater
That looks great, Joe! Looking forward to testing it. I guess I ll have to get hold of Max 7, though. Incidentally, did you have to use some kind of Max
Re: [korgpolyex] Testers wanted : Hawk 800 Max for Live editor
2014-12-16 by Michael Hawkins
Looks really nice! From: lists@joemattiello.com [korgpolyex] To: korgpolyex@yahoogroups.com Sent: Tuesday, December 16, 2014
Re: [korgpolyex] Testers wanted : Hawk 800 Max for Live editor
2014-12-16 by lists@...
Great, thanks for the responses so far. I just finished the extremely tedious task of making a pixel perfect layout in Max. This patcher uses the new Max 7