Yahoo Groups archive
Messages
Page 33 of 168 · 8362 messages matched
2008-07-11 by mikesonic77
memX ? yeah, please count me in. --- In analogue-sequencer@yahoogroups.com, "Colin Fraser" wrote: > > > > > do you have news about memory expansion?...cause i 've got 2 x P3 > > > now,without them...best regards Boop's > > I am planning to do another run of MemX, but I need a fir
2008-07-08 by boops.secretvibes
Hi Colin,very good news,the 2 x P3 work fine tonight,there was a micro short cut(hardware as you 've said)...very difficult to find....thanks for your informations...i've became a professional of harware and software P3 ;-)...zouuuuu !!!Print the last part of the manual...Best re
2008-07-08 by boops.secretvibes
hi,last good news,the P3 1.4 is uptade ,and finish ,every function work fine..thanks - In analogue-sequencer@yahoogroups.com, "boops.secretvibes" wrote: > > hi,Colin data ,tempo pots work fine now...is it possible velocity > don't work in version 3.95?i beleive ,it's time,to inst
2008-07-08 by boops.secretvibes
i 've made the firmware UPDATE 3.006C after this V3.2CHK2B7C > BOOT FLASH THEN I FLASH AND TRANSMIT ALL THE FILE(MORE DATA ON THE SCREEN). SCREEN ASK SIZE F180 THEN I BOOT BUT NOTHING HAPPENS I TRY A SECOND TIME;NOTHING;PERHAPS THE VERSION 3.006B WHICH WAS INSTALLED?THANKS > If i
2008-07-08 by boops.secretvibes
hi,Colin data ,tempo pots work fine now...is it possible velocity don't work in version 3.95?i beleive ,it's time,to install midiox now for uptaded the version 3.006C!!.. thanks --- In analogue-sequencer@yahoogroups.com, "boops.secretvibes" wrote: > > hi,Colin, at the end of the
2008-07-08 by boops.secretvibes
hi,Colin, at the end of the loading syx file of the firmware image ,is there a message by example "SUCCESS"?before i must reboot ?i dont touch the main board just put the chip in the 1.4 board (it worked perfectly)and when i unstall it :screen like this 1/3 BANK FTS TUNE (freeze)
2008-07-08 by Colin Fraser
If the P3 boots into firmware update mode, and successfully loads the firmware image, then reboots without showing a checksum error, but doesn't get any further, it seems more like a hardware problem. What exactly appears on the LCD display when it fails to boot ? Best regards, C
2008-07-08 by boops.secretvibes
hi,Colin, at the end of the loading syx file of the firmware image ,is there a message by example "SUCCESS"?before i must reboot ?i dont touch the main board just put the chip in the 1.4 board (it worked perfectly)and when i unstall it :screen like this 1/3 BANK FTS TUNE (freeze)
2008-07-08 by boops.secretvibes
hi,i find in the forum,forced and boot manually,and Download the file "p3-bootloader-v3.3-AT.syx" cause it seems mine is 3.2? wrote: > > hi,nobody have a little idea to follow..to give ,this CPU a second > chance to work...Boop's > > > --- In analogue-sequencer@yahoogroups.com, "
2008-07-08 by boops.secretvibes
hi,nobody have a little idea to follow..to give ,this CPU a second chance to work...Boop's --- In analogue-sequencer@yahoogroups.com, "boops.secretvibes" wrote: > > i 've made the firmware UPDATE 3.006C after this V3.2CHK2B7C > > BOOT FLASH > > THEN I FLASH AND TRANSMIT ALL THE F
2008-07-07 by boops.secretvibes
i 've made the firmware UPDATE 3.006C after this V3.2CHK2B7C > BOOT FLASH THEN I FLASH AND TRANSMIT ALL THE FILE(MORE DATA ON THE SCREEN). SCREEN ASK SIZE F180 THEN I BOOT BUT NOTHING HAPPENS I TRY A SECOND TIME;NOTHING;PERHAPS THE VERSION 3.006B WHICH WAS INSTALLED?THANKS > If i
2008-07-07 by Colin Fraser
If it gets as far as that screen, the bootloader is working. It would be odd for the OS to be corrupt but not to show a checksum error at boot. Try reloading the OS using firmware update mode - FUNC+PAGE at power on. Best regards, Colin Fraser Sequentix Music Systems Ltd http://w
2008-07-07 by boops.secretvibes
resurection.syx???? --- In analogue-sequencer@yahoogroups.com, "boops.secretvibes" wrote: > > hi,Colin ,i put the chip version 1.6 on the main board 1.4,unluckly > the soft is freezing on this this screen 1/6 > BANK FTS TUNE > i 've tried F1+STEP 7 ,freeze again. > i've tried to
2008-07-07 by boops.secretvibes
hi,Colin ,i put the chip version 1.6 on the main board 1.4,unluckly the soft is freezing on this this screen 1/6 BANK FTS TUNE i 've tried F1+STEP 7 ,freeze again. i've tried to get off the battery memories always 1/6 BANK FTS TUNE any steps work...what can i do?:-( i 've maded t
2008-07-07 by duncan
> Received today my LCD but don't know where to solder > > resistor, what is R19??? Completely confusing.. > > Look at this picture... > http://www.sequentix.com/build/cnst-main-img.htm > > You'll find a space for R19 just below the trimmer VR1, in the top right > corner of the b
2008-07-07 by boops.secretvibes
hi,thanks Colin for your informations..every seems alright for the moment...for the two P3(just change a lcd connection ,and bootload)i must try midi and learn the manual..also 2 memX for me please(not just one as i 've written)Best regards.. - In analogue-sequencer@yahoogroups.c
2008-07-07 by mo om
+ 1 for the MemX, please Colin Bravo boops d'avoir terminé ton P3! A+ Mo ----- Message d'origine ---- De : Wilfried M À : analogue-sequencer@yahoogroups.com Envoyé le : Lundi, 7 Juillet 2008, 12h34mn 09s Objet : Re : [analogue-sequencer] Re: Sequentix News Hello, Colin : I am in
2008-07-07 by Wilfried M
Hello, Colin : I am in for the MemX :-) Pacman : Wonderful night @ Nantes on march ... another night in our area ? Bye. ----- Message d'origine ---- De : boops.secretvibes À : analogue-sequencer@yahoogroups.com Envoyé le : Jeudi, 3 Juillet 2008, 10h30mn 55s Objet : [analogue-sequ
2008-07-06 by Colin Fraser
> -hello,i 've finished today the 2ND main board P3 kit 1.6 with > 3.006B,can i try it with my 1.4 others boards ,awaiting that i > bootload the 1.4 chip ?i 've got always this tempo problem with > this...work - no work (when i put my finger on the 3 pins of the pot, > working du
2008-07-06 by Colin Fraser
> hi,i find in this soft version("3.95" func + page get the 6 pages of > edit mode ,there is not the shortcut func + step 5 by example.. New features only appear in versions later than those they are added to. Due to restrictions in the space time continuum, I am unable to add ne
2008-07-06 by eddiehigginson
Hello again folks, just to let anybody interested know that the auction for my P3 finishes tonight (Monday 7th July) at 9:30pm BST on the dot. Cheers! -Eddie
2008-07-06 by boops.secretvibes
-hello,i 've finished today the 2ND main board P3 kit 1.6 with 3.006B,can i try it with my 1.4 others boards ,awaiting that i bootload the 1.4 chip ?i 've got always this tempo problem with this...work - no work (when i put my finger on the 3 pins of the pot, working during a few
2008-07-06 by boops.secretvibes
hi,i find in this soft version("3.95" func + page get the 6 pages of edit mode ,there is not the shortcut func + step 5 by example..i find also last step in edit pattern and change last step for 8 but when i run the P3 in pattern edit only a green bleep on step 1,not on the 8 ste
2008-07-06 by boops.secretvibes
thank you very much...my version is a 3.95 very old and strange,it seems there only 3 page in edit mode..in edit pattern the green bleep is only on 1 step "impossible to do instant gratification";-( ,i beleive there is tempo bug too,but not sure (perhaps a intermittant shortcut).
2008-07-06 by Doug Wellington
Try MIDI-OX: http://www.midiox.com Doug
2008-07-05 by boops.secretvibes
hi,is there somebody who has this file : p3-bootloader-v3.1-T89.syx in .mid cause with my nuendo or my RM1X i cant load it....for bootload a old version chip or perhaps a software for PC to do the job ..tranmit a .syx in my P3 1.4 version chip...thanks Boop's
2008-07-05 by boops.secretvibes
re,it's ok now an bad idc16 connection,i will try to load the last software and bootloader, print the end of manual,"l'aventure continue",in a few days i will begin to build a second one a 1.6 version thanks very much everybody ,and a special "chapeau bas" to Colin...please let a
2008-07-05 by boops.secretvibes
re i am just print the main board shematic....to check connection and voltage...mamaaaaamiaaaaaa!!!!
2008-07-05 by boops.secretvibes
--- In analogue-sequencer@yahoogroups.com, "Colin Fraser" wrote: > > Thank you very much Colin,your informations are precious for me and others . > > but i 've got( i hope )a last little problem with the tempo: (i think i can change the tempo at any the time ;without function? -
2008-07-05 by Colin Fraser
> but i 've got some little problems with ,led of fonction switch board > ,i think there are in the wrong way and the tempo and data pots no > working,on the diy page it seems there is some doubt about theses > connections ..is it the same for the 2 pots? The three pins of each c
2008-07-05 by boops.secretvibes
Hello,everybody i finish my first P3 last night ,after 4 months..looking for a kit,components shaeffer front panel..it is very beautiful ;-) but i 've got some little problems with ,led of fonction switch board ,i think there are in the wrong way and the tempo and data pots no wo
2008-07-04 by Hans Greuber
Honestly and it´s the second time that I´m answering that. I never asked that for free, I offered to pay what Colin could estimate. 2nd.. If you are happy with it, why are you bothering me and the list trying to frustrate me and other people instead of playing it? There are some
2008-07-04 by Ditton33
I think the P3 should be frozen as-is (bug fixes excepted) and Colin should be allowed to concentrate on the next project for which my only requirement is for it to have as many knobs and flashing lights as possible. :-D > >-----Original Message----- > >From: analogue-sequencer@y
2008-07-04 by Jim Combs
--- In analogue-sequencer@yahoogroups.com, "Steve" wrote: > > I hope I'm not overstepping my bounds here, but after the recent > discussions I feel compelled to say something. Expecting Colin to keep > adding more and more features to the P3 long after it has shipped, and > parti
2008-07-04 by kkonkkrete
As the main reason I'm on this list is to get news about the P3 follow-up, I thought now'd be a good time to chime in, as I'll definitely be buying one. Here are a couple of recommended features. Sorry this is long, but these are the result of a lot of playing live with other har
2008-07-03 by Hans Greuber
Thanks Colin, As I suggested.. You could do a custom OS for Dave,me and some other users to achieve the chord mode. There are lots of options that I don´t use or I´ll ever use as you all know that could be deleted to get the space for it. Other users would continue with the norma
2008-07-03 by Steve
I hope I'm not overstepping my bounds here, but after the recent discussions I feel compelled to say something. Expecting Colin to keep adding more and more features to the P3 long after it has shipped, and particularly a new OS version for a small user base without any renumerat
2008-07-03 by boops.secretvibes
--hi ,Colin count me too!!!Boops - In analogue-sequencer@yahoogroups.com, "syntaxdevelopment" wrote: > > --- In analogue-sequencer@yahoogroups.com, "Jack Deckard" > wrote: > > > > --- In analogue-sequencer@yahoogroups.com, "Colin Fraser" > I am > > planning to do another run of M
2008-07-03 by DB
Colin, Here's my 2 cents...or 5 P3's worth of requests... Any Chord Mode is better then No Chord Mode. If the only way tha you can implement it, is the way you indicated, it will still be better then not at all. I would love to see it implemented and then expanded on in the Cirkl
2008-07-03 by josh
Colin you are the master > Only things that have a low coding effort for worthwhile functionality gain > are likely to get much priority in P3 now. > And any bugfixes, of course. > Independent gating of aux notes is on the cards, since I saw how it could be > done relatively quic
2008-07-03 by Colin Fraser
> How is going the chord mode programming on the P3? IIRC the way I suggested it could be made to work didn't match with what was being asked for. There isn't space for any kind of UI to define chords manually. Maybe I can add a poly arp capture at some point. Only things that ha
2008-07-03 by eddiehigginson
Hi again folks, just letting anybody interested know there's only 4 days left to run on my P3 being auctioned on eBay, but you probably guessed that already from the 'Subject' line of this post... Cheers!
2008-07-03 by Colin Fraser
> If I dare ask the question to the forum : do we have a gestimation of > price at launch (just an idea as for example more near 1500 $ or near > 2500 $ ...) > maybe it's too early for Colin to estimate the cost... Way too early to say. I'm designing the CPU board to support a lo
2008-07-02 by syntaxdevelopment
--- In analogue-sequencer@yahoogroups.com, "Jack Deckard" wrote: > > --- In analogue-sequencer@yahoogroups.com, "Colin Fraser" > I am > planning to do another run of MemX, but I need a firm idea of demand > > before I order them, since I don't want to be left with any as > paperw
2008-07-02 by Colin f
If you mean the ringtone spam, it got deleted from the archive and the user bumped off the list. > -----Original Message----- > From: analogue-sequencer@yahoogroups.com > [mailto:analogue-sequencer@yahoogroups.com] On Behalf Of duncan > Sent: 02 July 2008 17:48 > To: analogue-seq
2008-07-02 by Jack Deckard
--- In analogue-sequencer@yahoogroups.com, "Colin Fraser" > I am planning to do another run of MemX, but I need a firm idea of demand > before I order them, since I don't want to be left with any as paperweights. Count me in on a MemX, and can I get a LCD display at the same time
2008-07-02 by watson
im in the group of people that would like a lot of knobs and control On Sat, Jun 28, 2008 at 6:04 PM, hysham2000 wrote: > If I dare ask the question to the forum : do we have a gestimation of > price at launch (just an idea as for example more near 1500 $ or near > 2500 $ ...) >
2008-07-02 by duncan
..what happened to the last-post-but-one?
2008-07-01 by monads
Guys I just listed my P3 up. It's a short listing, starting out and $1! I'm downsizing my equipment these days but any questions let me know. monads
2008-07-01 by Hans Greuber
I vote for chord mode on P3 before, on Cirklon after. Hans > i also would like to vote for chord mode > > On Mon, Jun 30, 2008 at 8:49 PM, Hans Greuber > wrote: > >> >> Hi Colin >> >> >> How is going the chord mode programming on the P3? >> >> Is the new Cirklon on loeaded with t