Re: Film scanning and scratches
2001-08-29 by tynmansystems@yahoo.ca
Skid, Thanks for the tip on the scanHi-End group. It does look like another very useful group. ... able to answer your question the most ... nice bunch of
Messages
Browse messages
Page 2152 of 2186 · 109257 messages matched
1160 mis quad micro banding
2001-08-29 by Randy L
Hi list, My 1160/mis quad/varitone/Roark curve/cfs system on archival matte is producing beautiful prints right off the bat. The only problem is this dreaded
Re: [Digital BW] Film scanning and scratches
2001-08-29 by wparsons@evergreen-funds.com
Two suggestions: 1. (The least helpful, perhaps). I use a Nikon scanner and find it useful for dust, but not particularly for scratches. 2. Just as I did in
Re: MIS VM Initial Impressions and Questions
2001-08-29 by Tom Keesling
... should ... I hope that s the case. Please let us know what you find and I ll do the same when I get my virgin carts and MIS inks and get the CIS set up
RE: [Digital BW] what is this alignment box stuff? and 1160 microbanding
2001-08-29 by Nij
Randy, Alignment boxes are only printed on the Epson 1280/90 alignment prints. You shoudl try alignment on yours too - but it does the lines alignment which
what is this alignment box stuff? and 1160 microbanding
2001-08-29 by Randy L
Hi list, I have been away from the list for awhile and just signed back on. What is the alignment box about? I have never seen this? Are these boxes supposed
Re: [Digital BW] Digest Number 85
2001-08-29 by ncm
Ben, While the occasional scratch appears on negs it isn t the norm. I use a Nikon LS-2000 which is notoriously good at showing up any and all defects like
RE: [Digital BW] Digest Number 85
2001-08-29 by Nij
... ... Yes. If you use a scanner with a LED-type light source. This is the equivalent of a collimated light enlarger. Scanners with diffuse
Re: MIS VM Initial Impressions and Questions
2001-08-29 by Martin Wesley
Jerry, With the color carts in the 1280 both #5 squares were the least grainy which is the in alignment position, as I understand it. After installing the
Automating Spectrocam Measurements
2001-08-29 by Scott Hendershot
I noticed the talk of measuring 729 patches with a hand held spectrophotometer. I just wanted to share my solution to that tedious process.
Quadtone separation profiles
2001-08-29 by Dan Culbertson
I *think* I have a solution on how to make RGB profiles that do both softproofing *and* separation. I noticed that the Epson Standard profile that comes with
Re: [Digital BW] Digest Number 85
2001-08-29 by Bruce
on 8/28/2001 5:22 PM, DigitalBlackandWhiteThePrint@yahoogroups.com at ... try majordomo@lists.cix.co.uk to subscribe to the filmscanner mailing list. Yes, my
Re: [Digital BW] Re: MIS VM Initial Impressions and Questions
2001-08-29 by Jerry Olson
Yes. I think the Photomatte from Legion and Epson archival will be my main 2 papers, and the torchon for the quality stuff. Three s enough. However, that
Re: [Digital BW] Re: MIS VM Initial Impressions and Questions
2001-08-29 by Jerry Olson
Tom, I m aligning the heads with the MIS hextone inks. The #9 patch is the least grainy. I don t understand how that aligns the heads! I now have flawless
Re: [Digital BW] 1160 on refurbdepot not in stock
2001-08-29 by James E. Martz
I ordered one from them the end of May and got it a several weeks ago -- busted. I called Epson and they overnighted a replacement to me that s working
Re: Culbertson's RGB method A-OK
2001-08-29 by Dan Culbertson
... Not sure about the best source of Profiler Pro. I m still using the beta version that I got as a beta tester (which was essentially the same as the final
[Digital BW] Re: MIS VM Initial Impressions and Questions
2001-08-29 by Tom Keesling
Martin, That prospect concerns me. I had been trying to get a good color alignment with the Piezo Color inks without success and currently have no idea whether
[Digital BW] Re: MIS VM Initial Impressions and Questions
2001-08-29 by Tom Keesling
Jerry, I forgot to comment on the length of time it takes to run the alignment procedure. I m accustomed to the procedure on my 3000 and didn t usually bother
[Digital BW] Re: MIS VM Initial Impressions and Questions
2001-08-29 by Tom Keesling
That s interesting...and good to hear! If you have that much latitude, I wonder why, given your experience with the 1280, I and so many others have had such
Re: ColorSync/Epson RGB workflow [was Toning]
2001-08-29 by Tyler Boley
Antonis, here s the confusing part, and you must excuse me cause I m a Mac guy... Working with Steve Meyers on his PC system, we discovered it made a huge
Re: [Digital BW] 1160 on refurbdepot not in stock
2001-08-29 by ternahan
Geo Data is shipping next week. trish ternahan@gentlelens.net From: Antonis Ricos Reply-To:
Re: [Digital BW] Re: MIS VM Initial Impressions and Questions
2001-08-29 by Jerry Olson
Tom, Well actually, that is interesting. The prints I have been printing aren t that much different from the ones I am now getting with the heads properly
Re: ColorSync/Epson RGB workflow [was Toning]
2001-08-29 by Antonis Ricos
Good point, Tyler. And that s why I stay clear of having the Epson driver do _anything_ at all with a file - but I realize that some workflows require
1160 on refurbdepot not in stock
2001-08-29 by Antonis Ricos
This may already be old news to those who have tried it, but if you happen to see that the 1160 is in stock at defurbdepot, don t bite. It s a lie to get
[Digital BW] Re: MIS VM Initial Impressions and Questions
2001-08-28 by Martin Wesley
Tom, That is what I am getting except I wasn t smart enough to read closely and put the same sheet of paper back in. Really should just use the back to the
[Digital BW] Re: MIS VM Initial Impressions and Questions
2001-08-28 by Martin Wesley
Jerry, What platform are you on? I m running Windows 2000. Maybe there is a difference in the driver? Martin ... nozzle check, not 3. The color and black are
Re: [Digital BW] Re: CMYK workflow
2001-08-28 by Todd Flashner
No apologies necessary, my mistake! I see how my wording made it seem I was polarizing *us* onto opposite sides of a debate, but I was really trying to define
[Digital BW] Somerset Photo Enhanced Paper question/ Posterizing -- 1270 curves
2001-08-28 by Paul Roark
... printer. ... Each printer type takes it s own curves. Also the printer settings can be critical. Finally, the system is designed for Epson Archival Matte
RE: [Digital BW] Film scanning and scratches
2001-08-28 by Jason DeFontes
I used to spend a lot of time panning around my images at 100% magnification and manually spotting out every little speck of dust that I could find. Then I
RE: [Digital BW] Somerset Photo Enhanced Paper question/ Posterizing
2001-08-28 by Nij
You should be able to feel which is the printed side - otherwise - the printed side should stick to the bottom of your tongue :) Nij ... ...
[Digital BW] Re: MIS VM Initial Impressions and Questions
2001-08-28 by Tom Keesling
Just imagine how much better your recent work could have been had you figured this out sooner! Better late than never, eh? Tom ... the instructions, I
[Digital BW] Re: CMYK workflow
2001-08-28 by Tyler Boley
Because of my poor communication skills, I ve given you precisely the opposite impression I intended. I m really sorry, and I certainly hope no one stops
Re: A Print Exchange?
2001-08-28 by jackperk@yahoo.com
I d like to participate.
Re: [Digital BW] Film scanning and scratches
2001-08-28 by Johnny Deadman
... there is also Tony Sleep s excellent Filmscanner list. Go to http://www.halftone.co.uk/ and follow the filmscanner links on the lhs frame -- John
Re: Print edges
2001-08-28 by Jerry Olson
HighTheir Group! Does anyone know of a program for the MAC and photoshop that will make some of those Artsy Fartsy edges you see all over the place? I don t
Re: [Digital BW] Re: CMYK workflow
2001-08-28 by Todd Flashner
Well, you ve certainly done a nice job of plucking all the negative words out of what I said to make it look like I m up to no good. All I was asking was if
Re: [Digital BW] Film scanning and scratches
2001-08-28 by SKID Photography
... There is a Yahoo group: the name is: scanHi-End They will be able to answer your question the most authoritatively. We just joined the group and they
Re: [Digital BW] 4 Paul Roark: MIS VM and Piezo Questions
2001-08-28 by Jerry Olson
Afternoon Paul, Did you get the latest batch of prints? If so, what did you think? Jerry
Re: [Digital BW] Re: MIS VM Initial Impressions and Questions
2001-08-28 by Jerry Olson
Martin, Tom, Well, I m about as embarrassed as you can get. If I had just READ the instructions, I would have known to click on Next instead of
Re: [Digital BW] Film scanning and scratches
2001-08-28 by Shire,Stanley
Ben: We scan a great deal of film from 35mm to 4x5 each day. While dust will always be a problem (although I am delighted with the Ice3 on the Nikon 4k)
Pauls latest curves
2001-08-28 by blakephoto@mediaone.net
Where do I find the latest curves.? Are the ones on the MIS site the latest Ed Blake
Re: [Digital BW] MIS VM Initial Impressions and Questions
2001-08-28 by Tom Keesling
Thanks, Jerry. I just got an email from Paul off list with the latest curves attached. You talk about service!!!!! Tom ... latest set. ... color ... dated ...
[Digital BW] Re: MIS VM Initial Impressions and Questions
2001-08-28 by Tom Keesling
Jerry and Martin, I ve been playing with my 1280 for a few weeks now and mine prints on two pages. It prints the black alignment lines on one page and then
Somerset Photo Enhanced Paper question/ Posterizing
2001-08-28 by blake photo
Hello All: I am printing with MIS Vari Tone inks and Pauls workflow on a 1270 printer. I have two questions Is their a way to tell which side of this paper is
Re: [Digital BW] Re: MIS VM Initial Impressions and Questions
2001-08-28 by Jerry Olson
Martin, My 1280 printer only prints one page when selecting nozzle check, not 3. The color and black are printed on the same page, all 6 in a one row line.
Film scanning and scratches
2001-08-28 by tynmansystems@yahoo.ca
I tried to find a group that is focused on film scanning, but couldn t find one; hope this isn t too far off topic for this group. Over the past two year, I
Re: [Digital BW] MIS VM Initial Impressions and Questions
2001-08-28 by Jerry Olson
No they aren t the latest. Ask Paul at: paul.roark@verizon.net for the latest set. Jerry
[Digital BW] Re: CMYK workflow
2001-08-28 by Tyler Boley
... I m sorry, I didn t realize I was in a debate, on a side, had a case to prove, or was bantering. It s simply an idea that may or may not be useful, and if
Re: Culbertson's RGB method A-OK
2001-08-28 by Martin Wesley
Dan, Besides the Absolut for the daily cleaning of those pesky heads, what do you need to successfully run your RGB method? I m interested in giving it a try
Epson 7000 MIS Vari-tone Inks - UPDATE
2001-08-28 by Michael J. Kravit
Hello Everyone, Well, we packed up our home and away it went with the MOvers last FRiday. Unofrtunately the cloing on the new house fell through due to the