Emu XL-7 & MP-7 User's Group

Hi, Andrew 
can you give some example of outboard efx processor,
I would like to make my live sound more analogic...
Thank's 

On Oct 3, 2008, at 1:31 AM, Andrew <Alan_mansfield@...> wrote:


I have a couple of outboard efx processors that I like to use... so for instance, if I want to route my snares and cymbals to one of my out-board reverb processors through submix 1... I select those tracks (which are on their corresponding midi channels) and route them to send 2. I get the dry audio from those tracks/channels at submix 1, but the dry audio also shows up at the main-output as well. I understand that if I turn the send amout for send 2 past 0, that I should be hearing the wet audio at the mains, and the dry on the sub... but if it is set to 0, then I should only get the dry on the sub, and nothing at the main....but no matter what I do, I can't get it out of the main. And whenever I switch efx modes, (to apply efx to only 1 preset) the efx saved in whatever preset is assigned to the selected channel applies it's efx settings to every preset on every channel. Confusing, huh?

Andrew

> To: xl7@yahoogroups.com
> From: tttsystems@...
> Date: Thu, 2 Oct 2008 17:43:46 -0400
> Subject: Re: [xl7] What am I doing wrong with the efx?
> 
> All those words hurt my head...I'm going to have to read this a few times over to see where you are....
> 
> Bob
> El Segundo, CA
> 
> 
> -----Original Message-----
> >From: Andrew <Alan_mansfield@...>
> >Sent: Oct 2, 2008 4:52 PM
> >To: xl7@yahoogroups.com
> >Subject: [xl7] What am I doing wrong with the efx?
> >
> >
> >It's my understanding that the effects on the XL-7 can either be used on only 1 preset, using the effects setting stored in that preset... or set up to run the same effects setting on every midi channel, using the 4 sends to control the amount of effect applied to each send, as well as selecting which output that send is routed to... or bypassed all together. When I bypass the effects, as expected, there are no effects... cool. However when I try to only run effects on one preset, I end up hearing that presets stored effects setting on every channels preset... and whenever I set it up to apply its effects to all presets through the sends, it works pretty much the way I think it should, except that whatever I set to sends 2 and 3 (sub mix 1 and 2) also shows up at the main output, even with those send levels all set to 0. I guess what I'm trying to accomplish is, if I set it up to only run its effects on one preset, that the effects only appear on that
 preset, and not on all of them... or if I set it up to apply its effects to everything through the sends, that whatever I route to sends 2 and 3 will only out-put the dry audio at the 2 sub-mixes if I set their send levels to 0. Any ideas?
> >
> >Andrew
> >
> >__________________________________________________________
> >Stay up to date on your PC, the Web, and your mobile phone with Windows Live.
> >http://clk.atdmt.com/MRT/go/msnnkwxp1020093185mrt/direct/01/
> >
> >[Non-text portions of this message have been removed]
> >
> 
> 
> ------------------------------------
> 
> Yahoo! Groups Links
> 
> 
> 

__________________________________________________________
Stay up to date on your PC, the Web, and your mobile phone with Windows Live.
http://clk.atdmt.com/MRT/go/msnnkwxp1020093185mrt/direct/01/

[Non-text portions of this message have been removed]





      

[Non-text portions of this message have been removed]