MOTM

I'd *love* a CV quantizer - I've tried using my Miniwaves for
quantization, but 8-bit lookup tables aren't accurate enough for
pleasant tuning!  Ideally a quantizer with at least two channels...

On the list below, I'd be particularly interested in the 130 Pan/Fade,
810 VC-EG, 2?? Delay and 450 FFB.  (Oh, and the vocoder, if I could
afford it!)

(I'm also really tempted by the modcan vector fader.  Anyone made a
black panel for that one?)

Harry

--- In motm@yahoogroups.com, "Miguel Mendoza" <miguel@...> wrote:
>
> Is it possible that nobody is interested on a CV quantizer? I really
miss this, so much that I bought one in Eurorack format... I'm also
missing a wavetable module.
> 
> Regards.
> 
> Miguel.
> 
> 
>   ----- Original Message ----- 
>   From: Paul Schreiber 
>   To: George Kisslak 
>   Cc: MOTM List 
>   Sent: Saturday, February 14, 2009 6:02 AM
>   Subject: [motm] List of proposed/discussed modules
> 
> 
>   Thanks for the list (going back to 1998!). I will get with JH and
see what 
>   the status is for these (a lot of these are his designs).
> 
>   I many cases, the only reason I never made these into a product
was the 
>   large number of parts (I know there are folks that lust for the
uber-500 
>   part MOTM kit). This also translates to large physical size of the pc 
>   boards. But, there are a few mechanical 'tricks' that I can play
to allow 
>   some of these to fit into cabinets people have already built.
> 
>   Then again: this makes the SMT route attractive because there is
*very 
>   little penalty* in having 100 resistors or 250. The pick-and-place
machine 
>   can put down 8 parts/second. Stuffing 100 parts costs me about
$1.50 in 
>   "machine time" (the total cost of a SMT board is screening the paste, 
>   machine time, then reflow solder time).
> 
>   What I'll do (next week) is review each of these and then report back:
> 
>   a) is a through-hole version possible?
>   b) is it SMT only?
> 
>   And then everyone can vote what is of interest, and what is not. I'm 
>   perfectly willing to work on what people wish for.
> 
>   Paul S.
> 
>   > All of the following modules have been discussed at one time or
other on
>   > this list since 2000.
>   >
>   > MOTM-2?? Dual 10000ms Delay (mentioned 8/19/00)
>   > MOTM-430 JH's Variable Slope Hi-Pass VCF
>   > MOTM-4?? JH's Dual Moog Ladder VCF
>   > MOTM-470 SEM VCF w/morphing output
>   > MOTM-475 Crow's GX-1 BP Filter
>   > MOTM-4?? Matrix-12 15-Mode VCF
>   > MOTM-880 VC Filter Envelope Generator (CS-80)
>   > MOTM-??? Random Vibrato Source (mentioned 11/23/00)
>   >
>   > These are unique but SMT:
>   >
>   > MOTM-102 Noise/ASR (2008)
>   > MOTM-520 Cloud Generator (in development w/521)
>   > MOTM-530 Envelope Nest (bizarre EG)
>   > MOTM-540 Munging Decimator (VC bit-rate reduction)
>   > MOTM-550 Rhythm Wheel (Seq/ASR/S&H w/pattern gen)
>   >
>   > These may not be unique but I believe the quality and unique
features 
>   > would
>   > make them attractive. Some are SMT though.
>   >
>   > MOTM-125 Pulse Width Multiplier (Crow/Anderton 4/10/2002)
>   > MOTM-130 Dual Pan/Fade VCA
>   > MOTM-180 Triple Preamp
>   > MOTM-450 Fixed Filter Bank (in development)
>   > MOTM-460 ARP 2600-4072 VCF
>   > MOTM-4?? Bi-Phase Clone
>   > MOTM-600 uSequencer
>   > MOTM-810 JH's VC EG (mentioned 4/2001)
>   > MOTM-840 Envelope Follower/Compressor
>   > MOTM-??? Joystick Interface
>   > MOTM-??? DoMOAS (Daughter of Mother of all Sequencers)
>   > MOTM-??? VC Phase Shifter
>   > MOTM-??? Synthtech Vocoder
>