Emax

Hi Brian
Did you change the jumper settings?. I will have to check if there's a auto detect on the EIII and get back to you. Have you tried contacting Rob on the Emu Archive  site? He's the man who can really guide you.
Cheers,

Colin
  ----- Original Message ----- 
  From: brian_ronn <brian_ronn@...> 
  To: emax@yahoogroups.com 
  Sent: Tuesday, February 18, 2003 12:33 PM
  Subject: [emax] Re: EIII harddisk boot problem


  I've tried to set the HD to ID 1 and 4 without any boot success. When 
  I set the ID to 1 or 4 the EIII waits 3 or 4 times longer before it 
  proceds scanning the scsi chain. I've tried with 2 different Seagate 
  ST51080N hd's which should work with the keyboard, but not in my 
  case. I then tried to install one of the ST51080N disks in a EIIIx 
  (modul) with success. In the EIIIx the hd boots as it should.

  When I insert the original 43 Mb hd in the EIII the EIII will boot.

  I can't figure this out.....

  Thanx for helping out

  Brian

  --- In emax@yahoogroups.com, "Colin Ross" <colin.a.ross@b...> wrote:
  > Hi again,
  > Try a new install and set the HD to ID 01. Tell the EIII to look ID 
  01 on bootup.
  > Hope this helps.
  > Regards,
  > Colin
  > 
  >   ----- Original Message ----- 
  >   From: brian_ronn <brian_ronn@y...> 
  >   To: emax@yahoogroups.com 
  >   Sent: Monday, February 17, 2003 11:53 AM
  >   Subject: [emax] Re: EIII harddisk boot problem
  > 
  > 
  >   It is the EIII (keyboard version). I've tried to boot up without 
  the 
  >   floppydisk in drive but the EIII just keeps scanning the scsi 
  ID's 
  >   from 0 to 7. The hd is formattet with OS2.42 and I've copied the 
  >   software from floppy to the hd. I can access any module on the 
  front 
  >   panel which loads a bit of the OS software from the hd and I can 
  also 
  >   load entire banks from the hd. It just wont boot. Any suggestions?
  > 
  >   --- In emax@yahoogroups.com, "Pedro H" <sotavento1999@h...> wrote:
  >   > Is it Emu III or Emu III XP?
  >   > 
  >   >   ----- Original Message ----- 
  >   >   From: Colin Ross 
  >   >   To: emax@yahoogroups.com 
  >   >   Sent: Friday, February 14, 2003 12:14 PM
  >   >   Subject: Re: [emax] EIII harddisk boot problem
  >   > 
  >   > 
  >   >   Hi There
  >   >   do not put the disk in the floppy drive so it will search for 
  the 
  >   one on the HD.
  >   >   Cheers
  >   > 
  >   >   Colin
  >   >     ----- Original Message ----- 
  >   >     From: brian_ronn <brian_ronn@y...> 
  >   >     To: emax@yahoogroups.com 
  >   >     Sent: Thursday, February 13, 2003 11:05 PM
  >   >     Subject: [emax] EIII harddisk boot problem
  >   > 
  >   > 
  >   >     I have the OS2.42 boot disc (the latest OS) for the EIII. 
  I've 
  >   set 
  >   >     the scsi id this way: floppy id=0, hd=1 and EIII=6 but the 
  EIII 
  >   >     won't boot from the ST51080N hd. I have also formattet the 
  hd 
  >   and 
  >   >     copyed the software from diskette to hd, but the EIII won't 
  >   boot 
  >   >     from the hd only from floppy. I can access banks on the hd 
  and 
  >   >     access any module via the frontpanel but just won't boot.
  >   > 
  >   >     Do you know the jumper settings on the Seagate ST51080N hd?
  >   > 
  >   >     I'm thinking about putting the hd to an external hd-case 
  and I 
  >   would 
  >   >     want to disconnect the power of the center ventilator which 
  >   cools 
  >   >     the hd (because of the noise), would you advise me not to 
  >   disconnet 
  >   >     the ventilator maybe because of the heat level on the pcb 
  >   boards?
  >   > 
  >   >     Thanx
  >   > 
  >   >     Brian
  >   > 
  >   > 
  >   > 
  >   > 
  >   >     Emax and Emax II User's Group Website
  >   > 
  >   >     http://www.silveriafamily.com 
  >   > 
  >   >     Your use of Yahoo! Groups is subject to the Yahoo! Terms of 
  >   Service. 
  >   > 
  >   > 
  >   >   [Non-text portions of this message have been removed]
  >   > 
  >   > 
  >   >   Emax and Emax II User's Group Website
  >   > 
  >   >   http://www.silveriafamily.com 
  >   > 
  >   >   Your use of Yahoo! Groups is subject to the Yahoo! Terms of 
  >   Service. 
  >   > 
  >   > 
  >   > 
  >   > [Non-text portions of this message have been removed]
  > 
  > 
  >         Yahoo! Groups Sponsor 
  >               ADVERTISEMENT
  >              
  >        
  >        
  > 
  >   Emax and Emax II User's Group Website
  > 
  >   http://www.silveriafamily.com 
  > 
  >   Your use of Yahoo! Groups is subject to the Yahoo! Terms of 
  Service. 
  > 
  > 
  > [Non-text portions of this message have been removed]


        Yahoo! Groups Sponsor 
              ADVERTISEMENT
             
       
       

  Emax and Emax II User's Group Website

  http://www.silveriafamily.com 

  Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service. 


[Non-text portions of this message have been removed]