Emax

I've tried to set the HD to ID 1 and 4 without any boot success. When 
I set the ID to 1 or 4 the EIII waits 3 or 4 times longer before it 
proceds scanning the scsi chain. I've tried with 2 different Seagate 
ST51080N hd's which should work with the keyboard, but not in my 
case. I then tried to install one of the ST51080N disks in a EIIIx 
(modul) with success. In the EIIIx the hd boots as it should.

When I insert the original 43 Mb hd in the EIII the EIII will boot.

I can't figure this out.....

Thanx for helping out

Brian

--- In emax@yahoogroups.com, "Colin Ross" <colin.a.ross@b...> wrote:
> Hi again,
> Try a new install and set the HD to ID 01. Tell the EIII to look ID 
01 on bootup.
> Hope this helps.
> Regards,
> Colin
> 
>   ----- Original Message ----- 
>   From: brian_ronn <brian_ronn@y...> 
>   To: emax@yahoogroups.com 
>   Sent: Monday, February 17, 2003 11:53 AM
>   Subject: [emax] Re: EIII harddisk boot problem
> 
> 
>   It is the EIII (keyboard version). I've tried to boot up without 
the 
>   floppydisk in drive but the EIII just keeps scanning the scsi 
ID's 
>   from 0 to 7. The hd is formattet with OS2.42 and I've copied the 
>   software from floppy to the hd. I can access any module on the 
front 
>   panel which loads a bit of the OS software from the hd and I can 
also 
>   load entire banks from the hd. It just wont boot. Any suggestions?
> 
>   --- In emax@yahoogroups.com, "Pedro H" <sotavento1999@h...> wrote:
>   > Is it Emu III or Emu III XP?
>   > 
>   >   ----- Original Message ----- 
>   >   From: Colin Ross 
>   >   To: emax@yahoogroups.com 
>   >   Sent: Friday, February 14, 2003 12:14 PM
>   >   Subject: Re: [emax] EIII harddisk boot problem
>   > 
>   > 
>   >   Hi There
>   >   do not put the disk in the floppy drive so it will search for 
the 
>   one on the HD.
>   >   Cheers
>   > 
>   >   Colin
>   >     ----- Original Message ----- 
>   >     From: brian_ronn <brian_ronn@y...> 
>   >     To: emax@yahoogroups.com 
>   >     Sent: Thursday, February 13, 2003 11:05 PM
>   >     Subject: [emax] EIII harddisk boot problem
>   > 
>   > 
>   >     I have the OS2.42 boot disc (the latest OS) for the EIII. 
I've 
>   set 
>   >     the scsi id this way: floppy id=0, hd=1 and EIII=6 but the 
EIII 
>   >     won't boot from the ST51080N hd. I have also formattet the 
hd 
>   and 
>   >     copyed the software from diskette to hd, but the EIII won't 
>   boot 
>   >     from the hd only from floppy. I can access banks on the hd 
and 
>   >     access any module via the frontpanel but just won't boot.
>   > 
>   >     Do you know the jumper settings on the Seagate ST51080N hd?
>   > 
>   >     I'm thinking about putting the hd to an external hd-case 
and I 
>   would 
>   >     want to disconnect the power of the center ventilator which 
>   cools 
>   >     the hd (because of the noise), would you advise me not to 
>   disconnet 
>   >     the ventilator maybe because of the heat level on the pcb 
>   boards?
>   > 
>   >     Thanx
>   > 
>   >     Brian
>   > 
>   > 
>   > 
>   > 
>   >     Emax and Emax II User's Group Website
>   > 
>   >     http://www.silveriafamily.com 
>   > 
>   >     Your use of Yahoo! Groups is subject to the Yahoo! Terms of 
>   Service. 
>   > 
>   > 
>   >   [Non-text portions of this message have been removed]
>   > 
>   > 
>   >   Emax and Emax II User's Group Website
>   > 
>   >   http://www.silveriafamily.com 
>   > 
>   >   Your use of Yahoo! Groups is subject to the Yahoo! Terms of 
>   Service. 
>   > 
>   > 
>   > 
>   > [Non-text portions of this message have been removed]
> 
> 
>         Yahoo! Groups Sponsor 
>               ADVERTISEMENT
>              
>        
>        
> 
>   Emax and Emax II User's Group Website
> 
>   http://www.silveriafamily.com 
> 
>   Your use of Yahoo! Groups is subject to the Yahoo! Terms of 
Service. 
> 
> 
> [Non-text portions of this message have been removed]