Yahoo Groups archive

SergeModular

Index last updated: 2026-04-28 23:13 UTC

Thread

Re: Velocity

Re: Velocity

2002-04-24 by M. Blake Wilson

obidiah2001 wrote:

Hello all, I am having trouble figuring out how to get the serge to
respond to velocity (mostly for amplitude I suppose) via the
expressionist. Any assistance is greatly appreciated. - G. Miller
i assume you are sending a gate signal from the expressionist (i have one too!) to trigger an envelope, yes? and that env is then controlling your VCA, perhaps? simply mix the env CV with your velocity CV in a CV mixer, in which case your VCA will be shaped as expected by your env, and be controlled further (amplified) by your velocity voltage.

HTH,

blake

--
M. BLAKE WILSON, ATTORNEY @ LAW
phone: 619 234-2200
fax: 619 234-2219
email: mbwlaw@...
website: http://www.mattwilsonlaw.com

Re: Velocity

2002-04-24 by George Miller

Blake - thanks again for the reply - so I have gate 1
out to the gate on the asdr and the out of asdr into
the vca. In this setup I have cv 1 out into 1v/oct on
the nto - then I repatched the asdr cv out to my cv
pro along with cv out 3 (from exp.) which is set to
velocity . Still no effect. (no matter what the amount
is set to - on the exp.)
The exp. manual says that you use cv & gate as pairs
but cv 2 out tracks fine into another pco at the
1v/oct. without the corresponding gate. Where would
that (gate 2 out) go anyway ?? - g. man

__________________________________________________
Do You Yahoo!?
Everything you'll ever need on one web page
from News and Sport to Email and Music Charts
http://uk.my.yahoo.com

Re: Velocity

2002-04-24 by M. Blake Wilson

George Miller wrote:

Blake - thanks again for the reply - so I have gate 1
out to the gate on the asdr and the out of asdr into
the vca. In this setup I have cv 1 out into 1v/oct on
the nto - then I repatched the asdr cv out to my cv
pro along with cv out 3 (from exp.) which is set to
velocity . Still no effect. (no matter what the amount
is set to - on the exp.)
is cv 3 set to the same midi channel as one?

b.


The exp. manual says that you use cv & gate as pairs
but cv 2 out tracks fine into another pco at the
1v/oct. without the corresponding gate. Where would
that (gate 2 out) go anyway ?? - g. man

__________________________________________________
Do You Yahoo!?
Everything you'll ever need on one web page
from News and Sport to Email and Music Charts
http://uk.my.yahoo.com

To unsubscribe from this group, send an email to:
SergeModular-unsubscribe@yahoogroups.com

Keep on Patchin'!

Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.

--
M. BLAKE WILSON, ATTORNEY @ LAW
phone: 619 234-2200
fax: 619 234-2219
email: mbwlaw@...
website: http://www.mattwilsonlaw.com

Re: Velocity

2002-04-25 by George Miller

--- "M. Blake Wilson" <mbwlaw@...> wrote: >
Show quoted textHide quoted text
>
> George Miller wrote:
>
> > Blake - thanks again for the reply - so I have
> gate 1
> > out to the gate on the asdr and the out of asdr
> into
> > the vca. In this setup I have cv 1 out into
> 1v/oct on
> > the nto - then I repatched the asdr cv out to my
> cv
> > pro along with cv out 3 (from exp.) which is set
> to
> > velocity . Still no effect. (no matter what the
> amount
> > is set to - on the exp.)
>
> is cv 3 set to the same midi channel as one?
>
> b.

Hi - I had all the channels on omni, changed them to 1
and still no velocity. ?? - g.m.

__________________________________________________
Do You Yahoo!?
Everything you'll ever need on one web page
from News and Sport to Email and Music Charts
http://uk.my.yahoo.com

Move to quarantaine

This moves the raw source file on disk only. The archive index is not changed automatically, so you still need to run a manual refresh afterward.