Modular Synth Panels

hey all,

so i finished my sequential switch/ event sequencer this morning. it
roolz, all other seq's droolz!
; )

the up/down control, the reset and inhibit controls, inverted output,
mix input -- what a great module!
adding LFOs to certain steps makes it very very very fun, or even audio
-- get some FM klang on every fifth step, for example.

i added a gate bus jack for the switches, w/ a diode between each gate
output and switch, all switches' middle lugs bussed to the jack --
works great, but i used four different-colored LEDs, and not all gates
are at the same level (very close though). i'll take the tradeoff for
prettiness.

the bridechamber glide DOES NOT WORK when inserted before the mixer
output. the 4051 must be sendin' somethin' the glide doesn't like. i
think the 358 locked up, which was weird. maybe it was the 4051,
though; i didn't test it. so i put the glide after the circuit's
outputs, using a dual-gang pot for glide.

the audio-rate glide works well at audio-rate clocking. now if only we
had an ultra-sonic VCO... maybe just maybe someone will be coming out
w/ one pretty darn soon (hint hint)...

my step selection rotary is a little weird, though. some steps are
skipped, though i've checked my wiring 10 times...

i love this module. there is a forest of wire back there, so put on
some good tunes and relax; it'll take a while.

i'll be adding final pics to the site today or tomorrow, and i'll work
on some sound samples too.

cheers,
Scott Deyo
The Bridechamber
contact@...
http://www.bridechamber.com
Jealous Edison Record Kompany
http://www.jealousedison.com

Great, I just finished having mine drilled for leds so I can add switches.
Maybe you could add a little wiring diagram for guidance ( like one of 8) and exactly where
to cut the trace.

>
> hey all,
>
> so i finished my sequential switch/ event sequencer this morning. it
> roolz, all other seq's droolz!
> ; )
>
> the up/down control, the reset and inhibit controls, inverted output,
> mix input -- what a great module!
> adding LFOs to certain steps makes it very very very fun, or even audio
> -- get some FM klang on every fifth step, for example.
>
> i added a gate bus jack for the switches, w/ a diode between each gate
> output and switch, all switches' middle lugs bussed to the jack --
> works great, but i used four different-colored LEDs, and not all gates
> are at the same level (very close though). i'll take the tradeoff for
> prettiness.
>
> the bridechamber glide DOES NOT WORK when inserted before the mixer
> output. the 4051 must be sendin' somethin' the glide doesn't like. i
> think the 358 locked up, which was weird. maybe it was the 4051,
> though; i didn't test it. so i put the glide after the circuit's
> outputs, using a dual-gang pot for glide.
>
> the audio-rate glide works well at audio-rate clocking. now if only we
> had an ultra-sonic VCO... maybe just maybe someone will be coming out
> w/ one pretty darn soon (hint hint)...
>
> my step selection rotary is a little weird, though. some steps are
> skipped, though i've checked my wiring 10 times...
>
> i love this module. there is a forest of wire back there, so put on
> some good tunes and relax; it'll take a while.
>
> i'll be adding final pics to the site today or tomorrow, and i'll work
> on some sound samples too.
>
> cheers,
> Scott Deyo
> The Bridechamber
> contact@...
> http://www.bridechamber.com
> Jealous Edison Record Kompany
> http://www.jealousedison.com
>

I'll do that.

Scott Deyo
The Bridechamber
contact@...
http://www.bridechamber.com
Jealous Edison Record Kompany
http://www.jealousedison.com

On Jun 7, 2008, at 2:13 PM, adaaxs wrote:

> Great, I just finished having mine drilled for leds so I can add
> switches.
> Maybe you could add a little wiring diagram for guidance ( like one
> of 8) and exactly where
> to cut the trace.
> >
> > hey all,
> >
> > so i finished my sequential switch/ event sequencer this morning. it
> > roolz, all other seq's droolz!
> > ; )
> >
> > the up/down control, the reset and inhibit controls, inverted
> output,
> > mix input -- what a great module!
> > adding LFOs to certain steps makes it very very very fun, or even
> audio
> > -- get some FM klang on every fifth step, for example.
> >
> > i added a gate bus jack for the switches, w/ a diode between each
> gate
> > output and switch, all switches' middle lugs bussed to the jack --
> > works great, but i used four different-colored LEDs, and not all
> gates
> > are at the same level (very close though). i'll take the tradeoff
> for
> > prettiness.
> >
> > the bridechamber glide DOES NOT WORK when inserted before the mixer
> > output. the 4051 must be sendin' somethin' the glide doesn't like. i
> > think the 358 locked up, which was weird. maybe it was the 4051,
> > though; i didn't test it. so i put the glide after the circuit's
> > outputs, using a dual-gang pot for glide.
> >
> > the audio-rate glide works well at audio-rate clocking. now if only
> we
> > had an ultra-sonic VCO... maybe just maybe someone will be coming
> out
> > w/ one pretty darn soon (hint hint)...
> >
> > my step selection rotary is a little weird, though. some steps are
> > skipped, though i've checked my wiring 10 times...
> >
> > i love this module. there is a forest of wire back there, so put on
> > some good tunes and relax; it'll take a while.
> >
> > i'll be adding final pics to the site today or tomorrow, and i'll
> work
> > on some sound samples too.
> >
> > cheers,
> > Scott Deyo
> > The Bridechamber
> > contact@...
> > http://www.bridechamber.com
> > Jealous Edison Record Kompany
> > http://www.jealousedison.com
> >
>
>
>