| previous by date | index | next by date |
| previous in topic | topic list | next in topic |
Sent from my BlackBerry wireless handheld.
BTW: If we can get enough demand for them, Scott at Bridechamber (who is also keenly interested in this one) could do a run of MOTM format panels. I’ve already notified him of my interest some months back.
-Greg
From: motm@yahoogroups. com [mailto:motm@ yahoogroups. com] On Behalf Of Greg James
Sent: Sunday, February 15, 2009 1:41 PM
To: 'MOTM List'
Subject: RE: [motm] List of proposed/discussed modules
For your consideration:
http://m.bareille. free.fr/modular1 /quantix8/ quantix8. htm
-Greg
From: motm@yahoogroups. com [mailto:motm@ yahoogroups. com] On Behalf Of Miguel Mendoza
Sent: Sunday, February 15, 2009 12:28 PM
To: MOTM List
Subject: Re: [motm] List of proposed/discussed modules
Is it possible that nobody is interested on a CV quantizer? I really miss this, so much that I bought one in Eurorack format... I'm also missing a wavetable module.
Regards.
Miguel.
----- Original Message -----
From: Paul Schreiber
To: George Kisslak
Cc: MOTM List
Sent: Saturday, February 14, 2009 6:02 AM
Subject: [motm] List of proposed/discussed modules
Thanks for the list (going back to 1998!). I will get with JH and see what
the status is for these (a lot of these are his designs).
I many cases, the only reason I never made these into a product was the
large number of parts (I know there are folks that lust for the uber-500
part MOTM kit). This also translates to large physical size of the pc
boards. But, there are a few mechanical 'tricks' that I can play to allow
some of these to fit into cabinets people have already built.
Then again: this makes the SMT route attractive because there is ∗very
little penalty∗ in having 100 resistors or 250. The pick-and-place machine
can put down 8 parts/second. Stuffing 100 parts costs me about $1.50 in
"machine time" (the total cost of a SMT board is screening the paste,
machine time, then reflow solder time).
What I'll do (next week) is review each of these and then report back:
a) is a through-hole version possible?
b) is it SMT only?
And then everyone can vote what is of interest, and what is not. I'm
perfectly willing to work on what people wish for.
Paul S.
> All of the following modules have been discussed at one time or other on
> this list since 2000.
>
> MOTM-2?? Dual 10000ms Delay (mentioned 8/19/00)
> MOTM-430 JH's Variable Slope Hi-Pass VCF
> MOTM-4?? JH's Dual Moog Ladder VCF
> MOTM-470 SEM VCF w/morphing output
> MOTM-475 Crow's GX-1 BP Filter
> MOTM-4?? Matrix-12 15-Mode VCF
> MOTM-880 VC Filter Envelope Generator (CS-80)
> MOTM-??? Random Vibrato Source (mentioned 11/23/00)
>
> These are unique but SMT:
>
> MOTM-102 Noise/ASR (2008)
> MOTM-520 Cloud Generator (in development w/521)
> MOTM-530 Envelope Nest (bizarre EG)
> MOTM-540 Munging Decimator (VC bit-rate reduction)
> MOTM-550 Rhythm Wheel (Seq/ASR/S&H w/pattern gen)
>
> These may not be unique but I believe the quality and unique features
> would
> make them attractive. Some are SMT though.
>
> MOTM-125 Pulse Width Multiplier (Crow/Anderton 4/10/2002)
> MOTM-130 Dual Pan/Fade VCA
> MOTM-180 Triple Preamp
> MOTM-450 Fixed Filter Bank (in development)
> MOTM-460 ARP 2600-4072 VCF
> MOTM-4?? Bi-Phase Clone
> MOTM-600 uSequencer
> MOTM-810 JH's VC EG (mentioned 4/2001)
> MOTM-840 Envelope Follower/Compressor
> MOTM-??? Joystick Interface
> MOTM-??? DoMOAS (Daughter of Mother of all Sequencers)
> MOTM-??? VC Phase Shifter
> MOTM-??? Synthtech Vocoder