Dave wrote: "I'm running five power supplies so I did try to keep the filters and
vcos on a single supply without any other modules that could
generate noise or current variations (as in blinking leds)."
I would like a little more info on this. I have noisey amps and filters. Another problem I have that someone may know how to troubleshoot is that my Encore UEG's create little tick noises as they advance from stage to stage. I have 2 and they both do it. This could be from the noisey amps but I think I remeber it happening without the amps in the signal flow, any ideas?
Thanks,
-michael-
djbrow54 <davebr@...> wrote:
My layout reminds me of the Smithsonian. I had a great organization
and then I outgrew my structure and have expanded into two overflow
buildings.
I started with oscillators grouped together on the left in the
middle cabinet and filters on the right in the middle cabinet. The
lower cabinet was for my control and modulation sources so keyboard,
envelope generators, lfos, etc. The top right cabinet I reserved
for +5 modules (since that's where the triple supply is) and my more
complex modules so ribbon, MIDI-CV, Miniwave, TimeMachine, etc. I
also put my VCAs so they'd be close to my filters.
Then the order ended. I had my analog interfaces on the left to be
close to the reel-reel which is now on the right. My overflow
cabinet has filters, lfos, controllers, preamps, and mixers. I did
put both of my programmable controllers in one case on a dedicated
power supply.
I found with my cabinets that the physical aspect of the module had
a lot to do with placement. My spring reverb needed to be on a side
so the reverb tank was as far away from the power supply as
possible. My deeper modules needed to be in specific locations to
avoid the power supply and power distribution boards. The short
modules needed to be in front of the power supply. +5 modules need
to be in the cabinet with the triple power supply.
In retrospect, the only thing that made patching easier was to group
the modules that tend to have dedicated interconnects. The envelope
generators all need triggers and gates. The filters and vcos all
need 1v/oct CVs so I put multiples in the centers of these module
groupings.
I tended to move modules around to try and keep a logical order but
eventually decided this was too much work for too little gain. I
did replace all the screws with 5/16" and plastic washers to not
mark up the panel faces.
I'm running five power supplies so I did try to keep the filters and
vcos on a single supply without any other modules that could
generate noise or current variations (as in blinking leds).
Dave
--- In motm@yahoogroups.com, "wjhall11" wrote:
>
> All - we want to develop a page on our site to present
philosophies
of
> synth layout. We want to present your expert thoughts on the
subject
> (and thus also benefit from them ). So - for instance - when
you
> put your modules into your synth cases, what do you group together
and
> why? Do you put your Oscillators at the top, filters below? Why?
> What have you found to be most intuitive / ergonomic? Can you
point
> us to publications on the subject that have influenced you? Thank
you
> all. Bill and Will
>
Yahoo! Groups Links
<∗> To visit your group on the web, go to:
http://groups.yahoo.com/group/motm/
<∗> Your email settings:
Individual Email | Traditional
<∗> To change settings online go to:
http://groups.yahoo.com/group/motm/join
(Yahoo! ID required)
<∗> To change settings via email:
mailto:motm-digest@yahoogroups.com
mailto:motm-fullfeatured@yahoogroups.com
<∗> To unsubscribe from this group, send an email to:
motm-unsubscribe@yahoogroups.com
<∗> Your use of Yahoo! Groups is subject to:
http://docs.yahoo.com/info/terms/
Be a better Heartthrob. Get better relationship answers from someone who knows.
Yahoo! Answers - Check it out.