Sorry, this was meant for the group, not just for John
Paul H.
----- Original Message -----
From: "Paul Haneberg" <phaneber@...>
To: "John Loffink" <jloffink@...>
Sent: Wednesday, February 22, 2006 11:02 PM
Subject: Re: [motm] gate processor preview
> Okay, I'll be more specific
>
> The countersunk screw holes do not conflict with the .5U mounting hole
> locations.
> You can use any combination of .5U and 1U spaced modules across rail
> boundaries and at any locations.
> Here's all the numbers.
> If you still think it won't work, draw it.
>
> 1U=1.75"
> .5U=.875"
>
> Mounting Holes are centered .25 from the module edges.
>
> Assuming the left end of the Flat Rail is at 0"
> The following are the centers of the hole locations going along the X
> axis:
>
> .25" - 1U mounting hole
> .625 - .5U mounting hole
> .875" - Countersunk hole for wood mounting
> 1.125" - .5U mounting hole
> 1.5" - 1U mounting hole
> 2.0" - 1U mounting hole
> 2.375" - .5U mounting hole
> 2.875" - .5U mounting hole
> 3.25" - 1U mounting hole
> 3.75" - 1U mounting hole
> 4.125" - .5U mounting hole
> 4.375" - Countersunk hole for wood mounting
> 4.625" - .5U mounting hole
> 5.0" - 1U mounting hole
> 5.5" - 1U mounting hole
> 5.875" - .5U mounting hole
> 6.125" - Countersunk hole for wood mounting
> 6.375" - .5U mounting hole
> 6.75" - 1U mounting hole
> 7.25" - 1U mounting hole
> 7.625" - .5U mounting hole
> 8.125" - .5U mounting hole
> 8.5" - 1U mounting hole
> 9.0" - 1U mounting hole
> 9.375" - .5U mounting hole
> 9.625" - Countersunk hole for wood mounting
> 9.875" - .5U mounting hole
> 10.25" - 1U mounting hole
> 10.5" - Other end of Flat Rail
>
> 1U module boundaries would be at:
>
> 0.0"
> 1.75"
> 3.5"
> 5.25"
> 7.0"
> 8.75"
> and 10.5"
>
> .5U module boundaries would be at the above plus:
>
> 0.875"
> 2.625"
> 4.375"
> 6.125"
> 7.875"
> 9.625"
>
> The clearance at the edges of the countersunk holes is tight, but there is
> no conflict.
>
> Try it, it works.
>
> Paul H.
>
>
>
>
> ----- Original Message -----
> From: "John Loffink" <jloffink@...>
> To: "'Paul Haneberg'" <phaneber@...>; <motm@yahoogroups.com>
> Sent: Wednesday, February 22, 2006 9:41 PM
> Subject: RE: [motm] gate processor preview
>
>
>> ?
>>
>> The countersunk screw holes conflict with some of the 0.5U mounting
>> locations.
>>
>> John Loffink
>> The Microtonal Synthesis Web Site
>> http://www.microtonal-synthesis.com
>> The Wavemakers Synthesizer Web Site
>> http://www.wavemakers-synth.com
>>
>>
>>> -----Original Message-----
>>> From: motm@yahoogroups.com [mailto:motm@yahoogroups.com] On Behalf Of
>>> Paul
>>> Haneberg
>>>
>>> No, this assumes you could mount panels in 1.5U or .5U increments across
>>> 6U
>>> flat rail boundaries.
>>> The only assumption would be that you have a total of X∗6U, (unless of
>>> course you cut down a flat rail or two)
>>>
>>> Paul H.
>>>
>>
>>
>>
>>
>> Yahoo! Groups Links
>>
>>
>>
>>
>>
>>
>>
>