Jim, did you buy it in Europe or did you buy it from someone in the states ?
Before getting a converter I strongly suggest that you verify the output
from the mains transformer.
This is very dangerous so if you are not 100% sure how to do it, don?t !!!
I accept no responsibility for any problems caused by your part.
∗ Switch off and disconnect the SDS-V from the poweroutlet
∗ Open the SDS-V and locate the transformer
∗ Disconnect the secondary winding leads going from the transformer to the
mixer PCB. Make sure they don?t short out each other
or touch any metal
∗ Re-Connect the power source ( 120V ) and switch on the SDS-V
∗ Measure the AC voltage between the two leads
Tell us what value you are getting.
It could be that your SDS-V has a transformer made for 220/240V installed.
Hence the low readings from the 15VDC lines.
Or it could be that one voicecard is pulling the 15VDC down to roughly 5VDC.
This can be checked by removing all voicecards from the frame.
WT
----- Original Message -----
From: "Berk Aarts" <B.E.R.K@...>
To: <Simmons_Drums@yahoogroups.com>
Sent: Saturday, September 20, 2008 10:42 AM
Subject: Betr: Re: [Simmons Drums] SDSV Issues
> See if I get this correct: You are in the USA where 110 V is the mains
> standard?
> You have a English piece off gear where the mains is 220 V? Am I correct??
> If oyu don't put a powerturner in between, that is not gonna work (imo)
> Do you have the scematics, so you are sure you're measuring 5 where it
> should
> be 15Volt?
> Berk
>
>
>
>>-- Oorspronkelijk bericht --
>>To: Simmons_Drums@yahoogroups.com
>>From: "jimstew37" <jimstew37@...>
>>Date: Sat, 20 Sep 2008 00:33:07 -0000
>>Subject: Re: [Simmons Drums] SDSV Issues
>>Reply-To: Simmons_Drums@yahoogroups.com
>>
>>
>>Hello, all:
>>
>>Thanks for your comments! I have visited simmonsmuseum.com many times,
>>and downloaded several manuals. Extremely helpful site! I'm sure I'll
>>contact Wolfgang before long.
>>
>>At any rate, I've opened up my SDSV many times in the two weeks I've
>>had it, and I think I know where these internal "knobs" are, I just
>>don't know which adjusts what function. I agree, though, that channel
>>2 is the most useful, simply because adjusting chnl 3 & 4 is kind of a
>>pain, and "factory" sounds rarely are much good.
>>
>>I'm pretty convinced that the problem is the power supply, since this
>>unit was apparently not for export to the US. The reason I think this
>>is the issue is because I checked the voltage in a few of the slots
>>where the individual modules are fitted. It should be 15 vdc, but what
>>I'm getting is around 5vdc. If the power transformer is wound for
>>240vac at the primary, and, when it sees 115vac instead, the secondary
>>would end up putting out less than 15 v.
>>
>>Anyway, Patrice, what compressor do you suggest using? I think that
>>would be a great way to give this a little more punch when I get it
>>going. I'm primarily a guitarist, but I don't usually use much
>>compression - just whatever is in my effects processor, so I don't
>>know whether that would be effective here.
>>
>>Thanks again!
>>
>>Jim Stewart
>>
>>--- In Simmons_Drums@yahoogroups.com, Patrice Jacquot
>><Jacquot.Patrice@...> wrote:
>>>
>>> Hi Jim,
>>>
>>> Welcome to the lucky owners club !
>>>
>>> just a few words about the V ...
>>> Yes the factory sounds are not "unforgetable", & can be very
>>> disapointing. I personnaly never play them...especially the snare...
>>> they don't have the same level at all compared to my other settings.
>>> You might have a problem as well, on some componants too...but before
>
>>
>>> that you can check by yourself
>>>
>>> You need to know that these factory sounds can be set on the channel
>
>>> card itself (& inside...yep... you need to open it).
>>> so it can become a fourth real memory instead of the one you avoid all
>>
>>> the time ... ;- )
>>> I've been too lazy to do it myself...
>>>
>>> Anyway congratulations !
>>> It's not easy to find one anymore now...
>>>
>>>
>>> Hmmm.... just a personnal taste ; I personnaly recommend a good
>>> compressor on it ...
>>>
>>> Have fun & let us know how you go ahead with it ...
>>>
>>> Have a nice day !
>>> Patrice.
>>>
>>> PS ; to me all the tom channels are the same ...it will become L or R
>
>>
>>> on your mixer ...if you're using a premix ...which is better really....
>>
>>
>
>
>
>
>
>
>
> ------------------------------------
>
> Yahoo! Groups Links
>
>
>