Hello,
the diagnostic is difficult without the SDS9 on the table, but I'll try. You don't need a stereo pad to check, if you work with button mode or midi. Open the unit to check several things. (If you are not experienced, let a repair shop do it). All following parts are on the main PCB, most located in the area around the eprom sockets. First: Check for signal yes/no at pin4 on rim DAC (IC 31). If no, check, if counters IC 27 and 28 are working (you should hear different frequencies of the counter stages, if you have no scope). Is the very low beep you were talking of changing in frequency, if you alter the rims pitch?
Your trigger LED is working, so you should have an envelope at pin 14 of IC 31, verify that (check also the 3.9k resistor). If you have working counters and the envelope is present, change IC 31 .If you can hear a raw rim noise at the DACs output (pin 4), check signal flow to IC 33 pin 6. If you can hear the snare sound, this IC is not dead and you are lucky, because it is an expensive one (CEM 3372). Check all parts in the signal path from IC 31 to IC 33. IC 33 mixes the snare and the rim together (and more...), if you can hear the snare, all parts after IC33 are ok. There is also a CV regulating the balance between snare and rim sounds, you should test that on pin 5 of IC 33: If you alter the snare/rim balance, something must happen with the CV there (and the snare sound should fade out at least). If no change in voltage is noticed, you should check demux IC 65 and s/h TL074 (IC 13).
If you need the schematics, no problem. If you need the unit repaired, ask Thierry EPPHERRE from france, he is the specialist (godfather) for SDS9.
Good Luck.
Michael
----- Original Message -----
From: giamesimmons
To: Simmons_Drums@yahoogroups.com
Sent: Thursday, January 03, 2008 7:38 PM
Subject: Re: [Simmons Drums] sds9 proms dead? 2
There's a dedicated channel for the rimshot consisting of two proms:
one for rimshot and one for cross stick, you can program if you want
to use rimshot A or rimshot B..
However the input for the trigger signal is only one jack stereo: tip
for the snare and sleeve for rimshot. The rimshot so is activates
when you strike the border of the dual zone pad connected to this
stereo input. All of this in theory because I don't have the dual
zone pad... however I can trigger from a midi keyboard and the
rimshot channel don't want to work...
If I put the snare prom into the rimshot slot, it don't work.
If I put the rimshot prom into the snare slot: it's ok...
Giame
--- In Simmons_Drums@yahoogroups.com, jesper <jesper@...> wrote:
>
> giamesimmons skrev:
> >
> >
> > No, I'm doing test with the button tap function, that allow me to
test
> > the sounds without striking the pads...
> > To tell the truth, I'm not sure to have the stereo pad, as I
tried all
> > the pads with a stereo cable in the snare jack input, but no one
seems
> > to trigger the rimshot channel (no led lit). They should be all
sds9
> > pads because they have the rubber surface, even if they have a XLR
> > connector. I read that the snare pad should have a grey
coloured "O" on
> > the Simmons logo...but I haven't. So I tested with button tap
function
> > or with MIDI, using a keyboard as controller..
>
> OK, back to original post then;
>
> > "On my sds9 I can't get the rimshot sound. I made different
tests: I
> > know for shure that the proms are good, because if I put the
rimshot
> > prom in the socket of the snare, I can hear their sound.
> > I know also that the channel triggers correctly, because when I
put
> > the unit in manual tap mode and press the button of the rimshot
> > channel, I can see the trigger light on, and I can hear I very low
> > beep sound from the output... so I have to guess it's the internal
> > circuit that hold proms that is dead ?....I'm not so expert with
this
> > stuff..."
>
> I don't follow 100% then. Is the rimshot a dedicated prom and a
> dedicated channel or is it an add-on to the snare so to speak?
>
> If you put the snare prom in the rimshot socket then? Any sound?
>
> --
> electronically yours, jesper
> - -- --- ---- ----- ---- --- -- -
> www.electronic-obsession.se
> www.myspace.com/machinepop
> - -- --- ---- ----- ---- --- -- -
>
[Non-text portions of this message have been removed]