Jeremy,
"...except I substitute Flash copper for acid cooper, and 90/10
tin/lead instead of solder plate..."
What does it mean that you substitute 90/10 tin/lead instead of
solder plate? Can you elaborate?
Mike
--- In
Homebrew_PCBs@yahoogroups.com, "Jeremy Taylor" <jeremy@e...>
wrote:
> I've already told you all, several times. I use the Think and
Tinker method, except I substitute Flash copper for acid cooper, and
90/10 tin/lead instead of solder plate.
> Otherwise, Ron at think and tinker has done a very good job - and
that is where I've learned from , also the Caswell plating manual is
useful too.
> These links area already in the links section of this well
organized group.
>
> To put it bluntly - there is no FREE way to do this. You can either
buy pre-made chems, or you can spend that amount buying chemicals to
mix your own, but either way - you gotta spend some money. - What are
pth worth to you? will they make or break your project? Are you just
going to send out the boards, Do you want to make commercial grade
PCBs for a commercial project at home ? etc...
>
> For those of us doing PTH - I'm curious what your setup cost was?.
> Not including imaging, etching , drilling, etc..
> Just the PTH plating setup - for me I figure about $700 for ink,
plating kit, power regulation, power supply, and optional testing
equipment.
> My plating systems are built in to the same table top as my
developing, stripping, and etching systems I can do a max panel size
of 6X9.
>
> TSP is found at your average hardware store. - I think the key for
using it - is to get it HOT. I use a crock pot.
> JT
>
>
> ----- Original Message -----
> From: mikezcnc
> To: Homebrew_PCBs@yahoogroups.com
> Sent: Thursday, July 29, 2004 11:05 PM
> Subject: [Homebrew_PCBs] Re: Plating thruholes.
>
>
> Jeremy,
>
> 1. Where do you buy TSP? I chceked and it is some kind of a
cleaner.
> Sounds like a great suggestion. I searched this board and it
wasn't
> mentioned before.
>
> 2. What do you use for 'activating' the holes, to make the
conductive
> so the copper can be later deposited electrochemically?
>
> 3. For the others benefit, I am adding this link according to
> Jeremy's suggestion:
>
> http://www.caswellplating.com/kits/flashcopper.html
>
> Once Jeremy tells us what to use to make the holes conductive, we
> have all crucial details to make plated holes in a homebrew
manner,
> right?
>
> Mike
>
>
> --- In Homebrew_PCBs@yahoogroups.com, "Jeremy Taylor"
<jeremy@e...>
> wrote:
> > Adam
> > Flash copper (Alkaline) works better for me than acid copper.
In
> the future you might just want to say "copper plating"
leaving "acid"
> out as there is more than one way to plate copper.
> >
> > A quick dip in HOT tsp (tri sodium phosphate) does a great job
of
> pre-plate - pre lamination cleaning, and I suspect it would also
work
> well for tt (no sandpaper needed)
> >
> > JT
> >
> > ----- Original Message -----
> > From: Adam Seychell
> > To: Homebrew_PCBs@yahoogroups.com
> > Sent: Thursday, July 29, 2004 9:05 PM
> > Subject: Re: [Homebrew_PCBs] Re: Plating thruholes.
> >
> >
> > Dave Mucha wrote:
> > > --- In Homebrew_PCBs@yahoogroups.com, "mikezcnc"
<eemikez@c...>
> wrote:
> > >
> > >>I searched but weren't able to locate any posts on the
subject
> but
> > >
> > > I
> > >
> > >>recall that tehre was a dicussion of it. Does anyone know a
> simple
> > >>method that works on plating holes in a PCB? Mike
> > >
> > >
> > > I think the best home-brew (closer to professional sho)
unit is
> from
> > > Markus
> > >
> > > http://www.myhome.ch/mzingg/pcbstuff/tps/
> > >
> > >
> > > Also go back to the posts around 1100, maybe go directly to
> 1108 and
> > > start reading. IIRC, there was a detailed list of each
step
> needed.
> > >
> > > This is not for the faint of heart nor a simple one shot
> project.
> >
> > This is very true. The electroplating, and application of
your
> own
> > photoresists is the other major parts of the PTH process.
> >
> > In addition to etching, and photo imaging, you must;
> >
> > 1) cleaning PCB surface to prepare for electroplating.
> > 2) ability to apply your own dry film photoresist
> > 3) give holes the ability to plate.
> > 4) setup acid copper electroplating tank with proprietary
> additives.
> >
> > There are several methods of doing (3), such as with carbon
> dispersion,
> > electroless copper solutions, or with palladium colloid
> solutions. I
> > believe Markus's setup is using the palladium colloid
solutions.
> All
> > three processes have their problems, and I would say the most
> critical
> > step in the process.
> >
> > Let me know if you have any questions.
> >
> > Adam
> >
> >
> > Be sure to visit the group home and check for new Bookmarks
and
> files:
> > http://groups.yahoo.com/group/Homebrew_PCBs
> >
> >
> > Yahoo! Groups Sponsor
> > ADVERTISEMENT
> >
> >
> >
> >
> >
> > ----------------------------------------------------------------
----
> ----------
> > Yahoo! Groups Links
> >
> > a.. To visit your group on the web, go to:
> > http://groups.yahoo.com/group/Homebrew_PCBs/
> >
> > b.. To unsubscribe from this group, send an email to:
> > Homebrew_PCBs-unsubscribe@yahoogroups.com
> >
> > c.. Your use of Yahoo! Groups is subject to the Yahoo!
Terms of
> Service.
> >
> >
> >
> > [Non-text portions of this message have been removed]
>
>
>
> Be sure to visit the group home and check for new Bookmarks and
files:
> http://groups.yahoo.com/group/Homebrew_PCBs
>
>
> Yahoo! Groups Sponsor
> ADVERTISEMENT
>
>
>
>
>
> --------------------------------------------------------------------
----------
> Yahoo! Groups Links
>
> a.. To visit your group on the web, go to:
> http://groups.yahoo.com/group/Homebrew_PCBs/
>
> b.. To unsubscribe from this group, send an email to:
> Homebrew_PCBs-unsubscribe@yahoogroups.com
>
> c.. Your use of Yahoo! Groups is subject to the Yahoo! Terms of
Service.
>
>
>
> [Non-text portions of this message have been removed]