Well, I too have done this in the past.. but my boards are getting more comples... current board consists of one 28pdip, and four 16pdid chips, 3 DB9s, 2 power connectors, 8 ADC channel connectors, a TWI interface, about 40 caps, 6 inductors, 2 fuse holders, and a power supply..
All on a 3x4inch board... It's getting harder and harder to put this all on a single sided board
On Mon, 26 Dec 2005 03:00:29 -0000
"crankorgan" <
john@...> wrote:
> I use jumbers or the resistors themselves to make a jump so I
> don't need a double sided board.
>
> --- In Homebrew_PCBs@yahoogroups.com, James Washer <washer@t...> wrote:
> >
> >
> > Yes, I understand the need to arrange for either jumpers or "rivets"
> from one side to another. Thanks
> > On Sun, 25 Dec 2005 18:40:31 -0000
> > "crankorgan" <john@k...> wrote:
> >
> > > Two side is done using two register pins. The problem is you will
> > > have to add jumpers to make connections from one side of the board to
> > > the other. With a little thought you can make most boards single
> > > sided. If you let Eagle route your boards you will get double sided
> > > boards 9 out of 10 times.
> > >
> > > --- In Homebrew_PCBs@yahoogroups.com, James Washer <washer@t...>
> wrote:
> > > >
> > > > Two questions
> > > >
> > > > 1) Is it "reasonable" to mill double sided boards?
> > > > 2) Will Eagle(and scripts) provide code to do the drilling (I'd
> > > assume so, but I don't like to make assumptions)
> > > >
> > > > - jim
> > > >
> > > > On Sun, 25 Dec 2005 12:43:28 -0000
> > > > "crankorgan" <john@k...> wrote:
> > > >
> > > > > http://mynock.dhs.org/pcbmilling/
> > > > >
> > > > >
> > > > >
> > > > >
> > > > > --- In Homebrew_PCBs@yahoogroups.com, James Washer <washer@t...>
> > > wrote:
> > > > > >
> > > > > > Nice job John.
> > > > > >
> > > > > > Can you answer a few questions for me? How does one get from an
> > > > > Eagle "brd" to whatever CNC instructions (or whatever they are
> called,
> > > > > I don't know anything about CNC, sorry).
> > > > > >
> > > > > > What kind of a mill are you using?
> > > > > >
> > > > > > On Sat, 24 Dec 2005 13:17:38 -0000
> > > > > > "crankorgan" <john@k...> wrote:
> > > > > >
> > > > > > > From Eagle to a finished board in less than 1 hour each.
> > > > > > >
> > > > > > >
> > > > > > > Drilled,Sanded and Cut
> > > > > > >
> > > > > > > http://crankorgan.com/perfchop7.JPG
> > > > > > >
> > > > > > > Parts added
> > > > > > >
> > > > > > > http://crankorgan.com/perfchop9.JPG
> > > > > > >
> > > > > > >
> > > > > > >
> > > > > > >
> > > > > > >
> > > > > > >
> > > > > > >
> > > > > > > Be sure to visit the group home and check for new Links,
> Files,
> > > > > and Photos:
> > > > > > > http://groups.yahoo.com/group/Homebrew_PCBs
> > > > > > >
> > > > > > > If Files or Photos are running short of space, post them here:
> > > > > > > http://groups.yahoo.com/group/Homebrew_PCBs_Archives/
> > > > > > > Yahoo! Groups Links
> > > > > > >
> > > > > > >
> > > > > > >
> > > > > > >
> > > > > > >
> > > > > >
> > > > >
> > > > >
> > > > >
> > > > >
> > > > >
> > > > >
> > > > >
> > > > > Be sure to visit the group home and check for new Links, Files,
> > > and Photos:
> > > > > http://groups.yahoo.com/group/Homebrew_PCBs
> > > > >
> > > > > If Files or Photos are running short of space, post them here:
> > > > > http://groups.yahoo.com/group/Homebrew_PCBs_Archives/
> > > > > Yahoo! Groups Links
> > > > >
> > > > >
> > > > >
> > > > >
> > > > >
> > > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > > Be sure to visit the group home and check for new Links, Files,
> and Photos:
> > > http://groups.yahoo.com/group/Homebrew_PCBs
> > >
> > > If Files or Photos are running short of space, post them here:
> > > http://groups.yahoo.com/group/Homebrew_PCBs_Archives/
> > > Yahoo! Groups Links
> > >
> > >
> > >
> > >
> > >
> > >
> >
>
>
>
>
>
>
>
>
> Be sure to visit the group home and check for new Links, Files, and Photos:
> http://groups.yahoo.com/group/Homebrew_PCBs
>
> If Files or Photos are running short of space, post them here:
> http://groups.yahoo.com/group/Homebrew_PCBs_Archives/
> Yahoo! Groups Links
>
>
>
>
>