prophet 600 diagnostic eprom ? Anyone ?
2018-03-11 by coolscott_7@...
Hi all Anyone have a prophet 600 diagnostic eprom ? Or just the software so I can burn my own? Thanks!
Messages
Browse messages
Page 2 of 155 · 7723 messages matched
KORG MS-20 Mini - service manual
2018-02-07 by Cosmic Fugue
Hi guys, have this MS-20 Mini in for repair. Do any of you have a service manual you could share, thanks. Cosmo Sent from
Looking for AKAI EWI 4000s and 5000 Service manual
2018-02-02 by saxfred@...
Hello All I am a great fan of Vintage synths and Wind Controlers I have had Yamaha WX7 and 5 and I now have both EWI 4000s and 5000 (also a new Aodyo Sylphyo).
Re: Help needed with EDC SR-99..
2018-02-01 by jaydiplock@...
Ok, so the machine runs in Play mode? but won t let you write new patterns? Unfortunately I don t think I have the schematic for the 99 but from memory I
Re: [vintagesynthrepair] Re: Help needed with EDC SR-99..
2018-01-29 by Paul Rak
Turns out it was a 4011bp. I changed it for a 4011ube but it made no difference.. This message was sent from my phone. Please excuse the brevity and any typos.
Re: [vintagesynthrepair] Re: Help needed with EDC SR-99..
2018-01-29 by Paul Rak
1. Batteries. 2. I think I have a UBP installed. I will check. (I have encountered this issue on Boss DR-55s) There s a mass of wires and a trimmer pot on the
Re: Help needed with EDC SR-99..
2018-01-23 by jaydiplock@...
Couple of things to ask... are you running it on batteries or DC psu? Does it run in pattern play mode, ie is the clock running? Sometimes the 4011 needs to be
Help needed with EDC SR-99..
2018-01-22 by paul.rak@...
I have an EDC SR-99 drum machine that won t play nice. Basically, it won t go into pattern write mode. I have replaced the 4011 and tc5514 chips to no effect.
Tascam PCI-822
2018-01-20 by dwv1957@...
Anyone have the pinout for the breakaway cable, I tried emailing Tascam, but they said the information was not available, or if someone has one they would
NORD Stage - service manual
2018-01-18 by Cosmic Fugue
Anyone could share a service manual for NORD Stage that is not functioning good, thanks. Regards, Cosmo Sent from
Morpheus Memory
2017-12-14 by rpcfender@...
I am writing a Emu Morpheus library program and I have come up with a problem. I can t find a quick sysex bulk dump to grab the edit buffer, which is easy in
RE: [vintagesynthrepair] Dead Casio CZ1000 advice needed
2017-12-05 by Cosmic Fugue
Hi Paul, Check the adaptor for 9VDC. Next check +Vdd at +5V etc... Have you got a service manual or schematic? Cosmo Maltese Islands Sent from
Re: Dead Casio CZ1000 advice needed
2017-12-05 by fmmusic@...
Open it up and take a look. Might be something obvious that you can see. Open it up and take a look. Might be something obvious that you can see. Open it up
Re: Dead Casio CZ1000 advice needed
2017-12-05 by Frank M
Open it up and take a look. Might be something obvious that you can see. From what I remember, it s easier to work on if you temporarily cut the leads to the
Dead Casio CZ1000 advice needed
2017-11-30 by paul.rak@...
I have just bought a Casio CZ1000, which does not power up. I have tried batteries and a power adapter. Any advice on what to check first gratefully received..
Re: Korg RK-100
2017-11-25 by yamaha_dx5@...
Hi, those caps are extremely hard to find. The Korg EX-800 module uses the same switch+bezel+cap combo. I ve been looking for many years also for an
Re: AMI S10430 divider / keyer chips for sale
2017-11-22 by paul.rak@...
SOLD!
Re: Korg RK-100
2017-11-21 by dwv1957@...
I also need a binary file for the eprom, anyone have this, or could someone with an RK-100 copy the eprom for me? Dave
Moog MG-1
2017-11-21 by HUNTER, MICHAEL
Have any of you experienced an issue wherethe envelope generator works as follows: I n continuous mode, a playing note plays fine, but when you strike a key,
Re: AMI S10430 divider / keyer chips for sale
2017-11-16 by paul.rak@...
Oh, I forgot to mention: I m going to 3d-print the joystick stick from a design on thingiverse...
Re: Korg Delta Advice Needed - update and help needed..
2017-11-16 by paul.rak@...
Hi. Sorry about the lack of updates. I basically did other things for over a year! Eventually, I sourced a few untested S10430 chips form a very nice guy in
Re: AMI S10430 divider / keyer chips for sale
2017-11-16 by paul.rak@...
Bidding is at £16 for one of them. The other two are still on their first bid. Get in now while they are cheap! Auctions end at 9:30PM, 18th November..
New member Kawai XR150 organ schematic?
2017-11-15 by harryoder@...
Recently acquired a Kawai XR150 2 manual organ that has been partially parted out, both manuals (keyboards) are missing, but the rest is present and seems to
AMI S10430 divider / keyer chips for sale
2017-11-11 by paul.rak@...
Hi. I am selling THREE used AMI S10430 chips on ebay. They have all been tested in my Korg Delta. There were originally FOUR chips, but one is staying in the
Korg RK-100
2017-11-09 by dwv1957@...
I am looking for a couple switch caps for a Korg RK-100, or any info on other things that used the same switches. Dave
Re: M-audio Venom
2017-10-30 by Daniel Forró
I try to find Venom service manual without success. Does somebody has one by chance? I need to know spec for SMD cap C50 near headphones jack… Unfortunately
Re: [vintagesynthrepair] Re: LCD LM24064B - Roland G1000
2017-09-19 by marcusguita
Hi jdearing17, Display for roland G1000 have 14 pins without controller (old model). The new display avaiable, have 22 pins with controller. Could you explain
Korg Trident MKII Service manual
2017-09-18 by dwv1957@...
Does anyone have the full Korg Trident MKII service manual? I downloaded about 20 of them off the internet, but they where all just the schematics. Dave
Re: LCD LM24064B - Roland G1000
2017-09-14 by jdearing17@...
I use these, they have different colors available too. Good quality and cheap.
Re: LCD LM24064B - Roland G1000
2017-09-14 by jdearing17@...
I use these. There are different colors available as well.
LCD LM24064B - Roland G1000
2017-09-08 by marcusguita
Hi all, Does anyone know who has this LCD (LM24064B) for sale? It s for a roland G1000. Thanks!! Marcus Prestes
New file uploaded to vintagesynthrepair
2017-08-31 by vintagesynthrepair@yahoogroups.com
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the vintagesynthrepair group. File :
New file uploaded to vintagesynthrepair
2017-08-31 by vintagesynthrepair@yahoogroups.com
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the vintagesynthrepair group. File :
Re: [vintagesynthrepair] Roland JV-2080 schematic/service manual
2017-08-25 by Daniel Forró
Some yahoo groups don’t allow attachments to messages. Upload it please to Files section, or use some server like Yousendit, or Uschovna. Daniel Forro ...
Re: Roland JV-2080 schematic/service manual
2017-08-23 by xsony30@...
I have a pdf service manual but I can t attach it to this msg.
Roland JV-2080 schematic/service manual
2017-08-21 by David Scarponi
Can anybody help me find a source for a Roland JV-2080 schematic, service manual, or working power supply. My PS seems to have died but not so easy for my
Re: [vintagesynthrepair] Casiotone MT 70 Service manual
2017-08-18 by Daniel Forró
Hi, Robert, check your mail… Best regards! Daniel Forro ... Hi, Robert, check your mail… Best regards! Daniel Forro On Aug 17, 2017, at 20:13,
Casiotone MT 70 Service manual
2017-08-17 by roberflas@...
Hello, I need the service manual or schematics to repair and mod one Casiotone MT 70 that I own. Anyone can help me? Thank you in advance
Re: Alesis Midiverb II Issues
2017-08-11 by hr.public@...
I ve replaced power caps in a couple of these midiverbs. I ve would re-flow solder on the ground spot in pic2, but I doubt its the source of problem -hans
Re: [vintagesynthrepair] Yamaha CP10
2017-08-02 by Daniel Forró
I just purchased very nice vintage E piano Yamaha CP10. It’s without problem, visually like a new one, everything works, there’s just one small thing: in
Re: Roland V-Synth
2017-07-07 by rpcfender@...
Hi Rob No, I m not sure. It is on its way to Australia from the US and I am basing the voltage and power required from the picture of the back of the unit.
Casiotone 701 complete service manual needed
2017-07-04 by bryan alka
Hi all, looking for a Casio Casiotone 701 service manual if anyone has one laying around. I have the workbook that someone kindly shared with me but this just
Re: [vintagesynthrepair] Roland V-Synth
2017-07-04 by rob hukin
Hi Royce, Are you sure it needs converting? The service manual doesn’t show any detail for the PSU, but AC-IN is written 100 - 240V 50/60Hz, so I would
Re: Roland V-Synth
2017-07-03 by saxfred@...
Hi Royce I am also trying to get my hands on this service manual for the v Synth XT looks like it is difficult to get I will let you know if I can get it,
Re: Roland V-Synth
2017-07-03 by rpcfender@...
Sorry about the double post. I thought Yahoo had swallowed the first one. Royce
Roland V-Synth
2017-07-01 by rpcfender@...
Hi I am trying to track down information on the power supply of a V-Synth XT Anyone with a service manual or even circuit diagram? I need to convert from the
Roland V-Synth XT
2017-06-30 by rpcfender@...
Hi I m looking for some information. Ideally a service manual and /or circuit diagram for a Roland V-Synth XT I have one heading my way (Australia) from the US
Re: [vintagesynthrepair] SD-1 SM [1 Attachment]
2017-06-28 by Lope
Hi PeWe, thank you for helping me with this manual, but I need the Schematic manual.I have this one , and I need the other.Thanks a lot ...this yahoogroup is
Re: [vintagesynthrepair] Ensoniq SD1 Schematics Manual
2017-06-28 by Lope
Hi Daniel, first of all thank you for the manuals and for your interest on helping me.Second, I m argentine, do you speak spanish ??I ve seen the e-mail two
SD-1 SM
2017-06-22 by PeWe
Hello ! Hope that helps ... ... good luck and all the best P.