Good point about the alcohol. My bad to assume that
we'd all be on the same page.
Re: the repair shops: Yes, I am certain that there
are good tech's and shops out there (Kevin Lightner of Synthfool for one). I am
just really anal about my stuff and I look long and hard for the best condition
synth of a particular model and then spend even more time completely restoring
it cosmetically and taking it apart completely and cleaning / lubing it
refinishing the wood etc. Then to have some bozo F up my work, lose my hardware
and then have to give him money for the privilage just REALLY burns my ass.
Especially considering that it's so simple to take a couple of extra seconds to
organize and take care handling the equipment.
It's unfortunate but I have seen this happen more
often than not.
So um, you wouldn't happen to be in the L.A. area,
would you?
Scott
----- Original Message -----From: Keith NiverSent: Saturday, June 21, 2003 3:37 PMSubject: RE: [vintagesynthrepair] cleaning keyboard contactsBe careful saying alcohol. Several different types, isopropyl, denatured, straight, etc. Soap and water normally work fine, just make sure you use some air to blow them dry or let them dry overnight. Would not suggest using anything very strong on the pc board contacts as you may ruin them, and then it's all over but the weeping and the wailing.As for the one thread reply about repair shops, don't condemn repairs in general because of one bad apple. I happen to take great pride in my work and try my best to get it turned around as quickly as possible, especially for a working pro. I also make sure I don't have any screws or parts left over and do a thorough check before it leaves the bench. There is a group called MITA that certifies techs. I am a certified MITA tech and a Master Certified Tech for one manufacturer and also certified by several major manufacturers who oversee the work you do on a regular basis.Keith NiverMaster Certified Tech & Certified MITA tech-----Original Message-----
From: Scott A. Robb [mailto:soul.lux@...]
Sent: Saturday, June 21, 2003 10:58 AM
To: vintagesynthrepair@yahoogroups.com
Subject: Re: [vintagesynthrepair] cleaning keyboard contactsAlcohol should work fine. The only Korg who's keybed I have looked at is the MS-20 so it's probably different than yours.If it's like the keybeds (mfg. by Mitsubishi) on the Korg Mono/Poly, Memorymoog and OB-8 take a look here for cleaning instructions:Scott Rider is a brillian man but I would take slight issue with his suggestion to use an eraser on the contacts, this should not be necessary. You will want to use it (VERY GENTLY) on the black contact that is inside the rubber cup though and only a few gentle swipes. Hate to state the obvious but make sure you tet everything prior to buttoning it up.I usually use alcohol followed by a contact enhancer but the latter is not required.Scott Robb----- Original Message -----From: Richard CohenSent: Saturday, June 21, 2003 8:41 AMSubject: Re: [vintagesynthrepair] cleaning keyboard contactsyes a korg DW8000.
so i take it apart, and use cotton swabs and some sort of liquid and clean
the back of each key and the contact part of the synth engine...?
should i use alcohol or water? special formula?
>From: "Scott A. Robb" <soul.lux@...>
>Reply-To: vintagesynthrepair@yahoogroups.com
>To: <vintagesynthrepair@yahoogroups.com>
>Subject: Re: [vintagesynthrepair] Re: AC POWER CORD
>Date: Sat, 21 Jun 2003 08:30:02 -0700
>
>The thread is a little hazy (it's early, it could be me) but is this for
>;the Korg?
>
>Usually, cleaning the contacts is slightly time consuming but VERY simple.
>If you bring it somewhere else, you have to realize that for the most part,
>these people don't give a crap about your property and will pile other gear
>on top of it while it sets on a shelf for weeks (only weeks if you're
>lucky, could be months). Once they work on it they'll lay her on her face
>on a carpeted bench full of bits of wire lead and solder globs and slide it
>around etc. IOW, most don't give a crap about your stuff, it's just money
>for them.
>
>If you're really lucky, you'll even get your unit back with most of the
>fasteners (like the screws to close the cabinet or hold on the wood cheeks,
>etc.) still there!
>
>If at all possible, do this stuff yourself and stay away from repair shops
>unless you have absolutely NO OTHER alternative.
>
>I just got a white face Odyssey that the twit's over at MusicTek (North
>Hollywood, Ca) put some healthy scratches on .
>I've been unfortunate enough to buy two Oberheim's that have gone through
>these people that both took FIVE months to get back! You can pay them a
>"premium" rate (I think it's $180 an hour) and get on the "fast track" of
>an 8 week turn around. Both Obies were missin quite a bit of the mounting
>hardware.
>
>I am going tomorrow to help someone that had their OB-8 there for 5 months
>and got it back and they had not cleaned all of the contacts. It's under 90
>day warranty so he took it back and MusicTek has had it 3 months now - just
>to clean the contacts which they were paid to have supposedly done already!
>These people REALLY suck!
> ; ----- Original Message -----
> From: Richard Cohen
> To: vintagesynthrepair@yahoogroups.com
> Sent: Saturday, June 21, 2003 6:35 AM
> Subject: Re: [vintagesynthrepair] Re: AC POWER CORD
>;
>
> yeah... got it!
>
> no my problem is fixing the keys....
>
> out of a 61 note keyboard only about 9 work.
>
> ; someone mentioned cleaning the contacts...
>
> is this easy to do at home?
>
> how much would it be to get it done at samash... where the work is under
> warranty?
>
>
> ; thanks bro!
>
> >From: "chromal"
> >Reply-To: vintagesynthrepair@yahoogroups.com
> >To: vintagesynthrepair@yahoogroups.com
> >Subject: [vintagesynthrepair] Re: AC POWER CORD
> >Date: Sat, 21 Jun 2003 00:55:47 -0000
> >
> >Richierich954,
> >
> >you said you checked out hosa gear, but I wonder if you have
> >considered their PWC-178, which sounds like what you may be looking
>for...
> >
> >
> >Good Luck,
> >Ben
> >
> >;
> >--- In vintagesynthrepair@yahoogroups.com, "Richard Cohen"
> > wrote:
> > >
> > > hello everybody...
> > >
> > > i just bought a used korg dw8000 (as is) and need a 2 prong IEC
> >power cord.
> > >
> > > i tried radio shack, hosa, guitar center, music stores, and nobody
> >has them.
> > >
> > > any suggestions as to where i can get one of these is greatly
> >appreciated.
> > >
> > > thank you.
> > >
> > > _________________________________________________________________
> > > Add photos to your messages with MSN 8. Get 2 months FREE*.
> > > http://join.msn.com/?page=features/featuredemail
> >
>
> _________________________________________________________________
> The new MSN 8: smart spam protection and 2 months FREE*
> http://join.msn.com/?page=features/junkmail
>
>
> Yahoo! Groups Sponsor
> ; ADVERTISEMENT
>
>
>
>
> To unsubscribe from this group, send an email to:
>; vintagesynthrepair-unsubscribe@egroups.com
>
>
>
> Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.
>
_________________________________________________________________
Help STOP SPAM with the new MSN 8 and get 2 months FREE*
http://join.msn.com/?page=features/junkmail
To unsubscribe from this group, send an email to:
vintagesynthrepair-unsubscribe@egroups.com
Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.
To unsubscribe from this group, send an email to:
vintagesynthrepair-unsubscribe@egroups.com
Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.
To unsubscribe from this group, send an email to:
vintagesynthrepair-unsubscribe@egroups.com
Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.