some defects after battery leak
Started 2015-05-14 by johandevroede@yahoo.com
Threads
Recent topics
Crispy sound, anyone?
Started 2015-05-26 by landemaine@gmail.com
About the Sub OSC
Started 2015-05-04 by kluber@hotmail.com
OT: 50KB Juno 60 slider needed
Started 2015-05-29 by gil_we@yahoo.com
Key assign mode issue
Started 2015-04-16 by mpe1969@tpg.com.au
PolySix CPU question...
Started 2015-05-12 by noddyspuncture@hotmail.com
MG Frequency LED Always On?
Started 2015-05-03 by rp_brennan@yahoo.com
Issue with Voice One
Started 2015-04-23 by taylorjmandel@yahoo.com
Looking for tech in UK
Started 2015-04-07 by Tubbutec
FS: KiwiSix upgrade board
Started 2015-04-05 by klosmon
Introduction
Started 2011-05-13 by Ben Stuyts
Polysix programmer section issues
Started 2015-03-04 by radek.tymecki@op.pl
VCA EG mode issue with replacement KLM-367A
Started 2015-03-02 by etmachina@hotmail.com
VCA mode and attenuator circuit
Started 2015-02-16 by Joel Dalton
VCF waveform amplitude
Started 2015-02-08 by omega.aurigae@yahoo.com
Issue with patch Led's and Bank Led's after replacing buttons
Started 2015-01-16 by yanbu@comcast.net
Voice board wanted
Started 2015-01-14 by klosmon
Osc Temperature Sensistivity
Started 2015-01-11 by klosmon
Non-working attenuator
Started 2014-12-23 by tuk88@rocketmail.com
Korg Polysix, serial numbers and total production and sizes
Started 2014-12-29 by stalinjohansen@yahoo.com
Polysix 100/120V to 220/240V conversion - Swapping transformer?
Started 2014-12-25 by stalinjohansen@yahoo.com
Polysix sounds off
Started 2014-12-28 by Sava66
Tuning issue.
Started 2014-12-16 by pasitive@gmail.com
Grounding noise from main output when cable-jack is connected
Started 2014-12-26 by stalinjohansen@yahoo.com
KORG POLY 6 fixed with klm-367a caveat
Started 2014-12-19 by nmr2@rocketmail.com
klm 367 repair
Started 2014-02-23 by <vaporlock_32578@yahoo.com>
Odd sound with patch when playing Polysix
Started 2014-12-18 by mfaitkenjr@yahoo.com
D8048C needed
Started 2014-12-16 by Tubbutec
Some Issues
Started 2014-11-26 by nick.oring@gmail.com
Closeout on PolySix restoration top panel replica overlays
Started 2014-12-11 by synthgraphics@hotmail.com
fully recapping a vintage synth
Started 2014-12-03 by jim@saltlands.com
Japanese polysix
Started 2014-11-30 by Sava66
VCF behaviour
Started 2014-11-25 by fatdub11@yahoo.com
Voice board calibration
Started 2014-11-07 by f115@rocketmail.com
Arpeggiator Timing - Slight Irregularities?
Started 2014-11-15 by jim@saltlands.com
VR Trimmers on KLM366 board
Started 2014-11-13 by tomorrowstops@yahoo.com
Clone revisited
Started 2014-11-10 by riccorman@me.com
Polysix Service Manual Error list
Started 2014-11-07 by f115@rocketmail.com
Clone - MG always on by default
Started 2014-10-11 by f115@rocketmail.com
Refurb VS Replace P6 Power Supply - strange high pitch issue
Started 2014-10-27 by jim@saltlands.com
Cut traces - Factory Mod?
Started 2014-10-28 by jim@saltlands.com
Polysix KLM-367 clone board
Started 2014-10-25 by Johannes Hausensteiner
Kiwisix tuning
Started 2014-10-23 by cosmosandstardust@yahoo.com
Voice # 6 not staying in tune !!
Started 2014-10-08 by jamieantonelli1978@yahoo.com
just got a junker...
Started 2014-10-11 by ftyjytjdrtjy@yahoo.com
Volume fluctuations correlated to the filter resonance
Started 2014-09-28 by num_si@yahoo.com
EG Intensity knob not working
Started 2014-09-27 by Robert Fantinatto
IC22 on KLM367 (8048)
Started 2014-09-09 by lighterthanairflight@gmail.com
P6 / tuning / patches promlem
Started 2014-08-29 by jacklane@sbcglobal.net
arpeggiator stopped working
Started 2012-06-11 by radek