MOTM

1) MOTM-800 Rev B

The Rev B adds the circuitry to get full ADSR action with GATE only. The
older Rev A
pcbs are all gone. These will ship starting next Monday. Same price.

2) MOTM-100 going to MOTM-101

The MOTM-100 is now out of stock, and will be replaced by the MOTM-101. The
'101
adds the panel switch for Vibrato select, and adds a pot for Slew limiting.
NOTE!
the price will increase to $135 kit, $185 assembled.

Ship date will be Nov. 10th. Any MOTM-100 orders will be converted to
MOTM-101s.

3) MOTM-320

This will be the next module shipped. The sheet metal is due Friday of next
week. By then
I hope to write the manual and start kitting up. So, shipment will be right
at the end of this month.
PCBs are in, production prototype 100% operational. Ship it!!

4) MOTM-440

The '440 will ship after the '320. It is the SSM2040 LPF with VC-Q. Price is
$159 kit and $219 assembled.
I expect this will ship the week before Thanksgiving (around Nov 20th). Feel
free to order anytime. Designed
by Jurgen Haible, the king of the SSM filter clones.

5) Mixer

I expect this to ship around Dec 10th. No price, but guessing $159 just
because of the hardware!

6) Triple preamp/uVCO/Env follower

I would love to get these out this year. But if I'm lucky, I can get 1.
Probably the preamp just
because it's the easier of the bunch.

Happy '410 building! Let me know what you think/kit screwups/etc

Paul Schreiber

Paul Schreiber schrieb:

> From: "Paul Schreiber" <synth1@...>
>
> 1) MOTM-800 Rev B
>
> The Rev B adds the circuitry to get full ADSR action with GATE only. The
> older Rev A
> pcbs are all gone. These will ship starting next Monday. Same price.
>
> 2) MOTM-100 going to MOTM-101
>
> The MOTM-100 is now out of stock, and will be replaced by the MOTM-101. The
> '101
> adds the panel switch for Vibrato select, and adds a pot for Slew limiting.
> NOTE!
> the price will increase to $135 kit, $185 assembled.
>
> Ship date will be Nov. 10th. Any MOTM-100 orders will be converted to
> MOTM-101s.
>
> 3) MOTM-320
>
> This will be the next module shipped. The sheet metal is due Friday of next
> week. By then
> I hope to write the manual and start kitting up. So, shipment will be right
> at the end of this month.
> PCBs are in, production prototype 100% operational. Ship it!!
>
> 4) MOTM-440
>
> The '440 will ship after the '320. It is the SSM2040 LPF with VC-Q. Price is
> $159 kit and $219 assembled.
> I expect this will ship the week before Thanksgiving (around Nov 20th). Feel
> free to order anytime. Designed
> by Jurgen Haible, the king of the SSM filter clones.
>
> 5) Mixer
>
> I expect this to ship around Dec 10th. No price, but guessing $159 just
> because of the hardware!
>
> 6) Triple preamp/uVCO/Env follower
>
> I would love to get these out this year. But if I'm lucky, I can get 1.
> Probably the preamp just
> because it's the easier of the bunch.
>
> Happy '410 building! Let me know what you think/kit screwups/etc
>
> Paul Schreiber
>
> 
  whats a uVCO ? never heard of it.
thanks
Zsolt

I haven't seen a reply to this yet. We were talking about this maybe a month 
ago. It is simply a 1U VCO (hence micro) with basic features like 1V/OCT and 
LIN FM inputs, two simultaneous waveform outputs (one being SQUARE and the 
other mixing between TRI and SAW -- unless I'm mistaken -- via a waveshape 
pot) and four pots (waveshape, LIN FM attenuator, COARSE and FINE tuning). 
But no syncs, no EXP FM (other than the 1V/OCT input), no PWM or WIDTH 
controls or SINE out. But not skimping on the temp stability or other 
critical concerns. In other words, a good compliment to the MOTM 300 as a 
modulation source or an extra oscillator in a two three (or more) oscillator 
per voice patch. I can't remember the projected price, but it was like 2/3 
the cost of the 300.

John B.
I'm about 1/2 way done with my 410 (there's a lot of stuff to stuff in that 
PCB), I hope to finish it tonight.


In a message dated 10/13/99 10:44:39 AM, Zsolt.Homlokos@...-uni-bochum.de 
writes:

> whats a uVCO ? never heard of it.
>thanks
>Zsolt
>

The final design mentioned had a TRI out and a VARiable out going from
square to saw.

Projected price $159.00, attached is the proposed panel image.

Dave

> From: JWBarlow@...
>
> I haven't seen a reply to this yet. We were talking about this
> maybe a month
> ago. It is simply a 1U VCO (hence micro) with basic features like
> 1V/OCT and
> LIN FM inputs, two simultaneous waveform outputs (one being
> SQUARE and the
> other mixing between TRI and SAW -- unless I'm mistaken -- via a
> waveshape
> pot) and four pots (waveshape, LIN FM attenuator, COARSE and FINE
> tuning).
> But no syncs, no EXP FM (other than the 1V/OCT input), no PWM or WIDTH
> controls or SINE out. But not skimping on the temp stability or other
> critical concerns. In other words, a good compliment to the MOTM 300 as a
> modulation source or an extra oscillator in a two three (or more)
> oscillator
> per voice patch. I can't remember the projected price, but it was
> like 2/3
> the cost of the 300.
>

> In a message dated 10/13/99 10:44:39 AM,
> Zsolt.Homlokos@...-uni-bochum.de
> writes:
>
> > whats a uVCO ? never heard of it.
> >thanks
> >Zsolt
> >