Synth-DIY Yahoo! Groups Archives

Thread

CC#32 Bank Select??

2012-10-20 by bimmerfan222

I ran into a CC that has stumped me...

I setup a dropdown menu to pick Bank1, Bank2, Bank3, Bank4

I used CC#32 and use 0=B1  32=B2, 64=B3 & 96=B4

I get no reaction from the HAWK.. going manually into Global Mode will change Banks, but nada from the CC

any ideas?  I saw the Midi Imp. chart says "32 Bank Select (LSB)".  Then the description states, "uses two most significant bits so that you should send bank select data as 0-31=bank1,..."


Is this CC setup differently than the other standard CC's like VCF cutoff??

-Blaine

Re: [korgpolyex] CC#32 Bank Select??

2012-10-21 by Michael Hawkins

I shall have a look tomorrow and check to make sure this works.

Mike




________________________________

Show quoted textHide quoted text

 From: bimmerfan222 <bperkins211@...>
To: korgpolyex@yahoogroups.com 
Sent: Saturday, October 20, 2012 1:45 PM
Subject: [korgpolyex] CC#32 Bank Select??

I ran into a CC that has stumped me...

I setup a dropdown menu to pick Bank1, Bank2, Bank3, Bank4

I used CC#32 and use 0=B1  32=B2, 64=B3 & 96=B4

I get no reaction from the HAWK.. going manually into Global Mode will change Banks, but nada from the CC

any ideas?  I saw the Midi Imp. chart says "32 Bank Select (LSB)".  Then the description states, "uses two most significant bits so that you should send bank select data as 0-31=bank1,..."

Is this CC setup differently than the other standard CC's like VCF cutoff??

-Blaine

Re: [korgpolyex] CC#32 Bank Select??

2012-10-21 by Michael Hawkins

Check that global 16 matches your Bank Select MSB.

Global 16 defaults to 1. So you should send the bank select MSB as 1.

Or, if you're sending zero for the MSB then set global 16 to zero.

Mike





________________________________

Show quoted textHide quoted text

 From: Michael Hawkins <korgpolyex800@...>
To: "korgpolyex@yahoogroups.com" <korgpolyex@yahoogroups.com> 
Sent: Saturday, October 20, 2012 9:52 PM
Subject: Re: [korgpolyex] CC#32 Bank Select??

I shall have a look tomorrow and check to make sure this works.

Mike

________________________________
 From: bimmerfan222 <bperkins211@...>
To: korgpolyex@yahoogroups.com 
Sent: Saturday, October 20, 2012 1:45 PM
Subject: [korgpolyex] CC#32 Bank Select??

I ran into a CC that has stumped me...

I setup a dropdown menu to pick Bank1, Bank2, Bank3, Bank4

I used CC#32 and use 0=B1  32=B2, 64=B3 & 96=B4

I get no reaction from the HAWK.. going manually into Global Mode will change Banks, but nada from the CC

any ideas?  I saw the Midi Imp. chart says "32 Bank Select (LSB)".  Then the description states, "uses two most significant bits so that you should send bank select data as 0-31=bank1,..."

Is this CC setup differently than the other standard CC's like VCF cutoff??

-Blaine

Re: CC#32 Bank Select??

2012-10-21 by bimmerfan222

here's what Ctrlr is sending out-

[11:55:58:000959]: RAW:[f0 41 00 46 12 00 08 28 01 00 00 4f f7]
[11:56:04:000902]: RAW:[f0 41 00 46 12 00 08 28 01 02 00 4d f7]
[11:56:10:000078]: RAW:[f0 41 00 46 12 00 08 28 01 04 00 4b f7]
[11:56:13:000389]: RAW:[f0 41 00 46 12 00 08 28 01 06 00 49 f7]

thats B1-B4 in series.

Which byte am I after?
Is that even close to the instructions needed?



--- In korgpolyex@yahoogroups.com, Michael Hawkins <korgpolyex800@...> wrote:

Show quoted textHide quoted text

>
> Check that global 16 matches your Bank Select MSB.
> 
> Global 16 defaults to 1. So you should send the bank select MSB as 1.
> 
> Or, if you're sending zero for the MSB then set global 16 to zero.
> 
> Mike
> 
> 
> 
> 
> 
> ________________________________
>  From: Michael Hawkins <korgpolyex800@...>
> To: "korgpolyex@yahoogroups.com" <korgpolyex@yahoogroups.com> 
> Sent: Saturday, October 20, 2012 9:52 PM
> Subject: Re: [korgpolyex] CC#32 Bank Select??
>  
> 
> Â  
> I shall have a look tomorrow and check to make sure this works.
> 
> Mike
> 
> 
> 
> ________________________________
>  From: bimmerfan222 <bperkins211@...>
> To: korgpolyex@yahoogroups.com 
> Sent: Saturday, October 20, 2012 1:45 PM
> Subject: [korgpolyex] CC#32 Bank Select??
>  
> 
> Â  
> I ran into a CC that has stumped me...
> 
> I setup a dropdown menu to pick Bank1, Bank2, Bank3, Bank4
> 
> I used CC#32 and use 0=B1  32=B2, 64=B3 & 96=B4
> 
> I get no reaction from the HAWK.. going manually into Global Mode will change Banks, but nada from the CC
> 
> any ideas?  I saw the Midi Imp. chart says "32 Bank Select (LSB)".  Then the description states, "uses two most significant bits so that you should send bank select data as 0-31=bank1,..."
> 
> Is this CC setup differently than the other standard CC's like VCF cutoff??
> 
> -Blaine
>