Where can I get a service manual for EII ?
2003-09-11 by grkh2003
Hi, Does anyone know where can I get a full service manual for Emulator II ? Many thanks... :)
Messages
Browse messages
Page 44 of 48 · 2353 messages matched
One problem solved + I have some news
2003-09-07 by grkh2003
Hi again and thanks a lot for everyone s advices! :-) I solved the problem with the sample input (the reason was bad connection of internal cable)! The other 2
RE: [emulatorII-list] LCD inverter?
2003-09-07 by Rob Keeble
Hi, The standard LCD needs 100VAC, 400Hz.The inverter runs from 5VDC. www.backlights.co.uk are using the Pactel 5 at ?14.99. Farnell have a Pactel 5E for ?20.
LCD inverter?
2003-09-07 by kruz@beatbazar.com
Hi, anyone have the specs to replace the inverter for the EII lcd? If you can give me the Farnell order code, it would be awesone :) Thank you all... .kruz
Re: [emulatorII-list] Re: A several problems with EII
2003-09-06 by 3phase
Ups...that was what i just sugested :-) lots of traffic on the E II mailinglist :-)
Re: [emulatorII-list] Re: A several problems with EII
2003-09-06 by 3phase
I am not too into it, but when it works,... and later not..then it seems that the failure is happening after warming up...can be powersupply...can be broken
RE: [emulatorII-list] Re: A several problems with EII
2003-09-05 by Rob Keeble
Hi, The problem is the power supply. It needs to be cheked and repaired - Rob To Rob Keeble (and all others) I have a news, regarding my problems. Today I ve
Re: A several problems with EII
2003-09-05 by grkh2003
Hi, and thanks a lot, guys! You are great! *** To Rob Keeble (and all others) I have a news, regarding my problems. Today I ve discovered the following new
Re: [emulatorII-list] A several problems with EII
2003-09-05 by Simon Wotton
hey greg! i ´can´t help you, but if you want to repair it, i can give you a REALLY good and cheap adress for repair in vienna!!! depends on where you are
RE: [emulatorII-list] A several problems with EII
2003-09-04 by Rob Keeble
Hi, Welcome aboard! 1. Sounds like the sampling input electronics are in trouble, have a look at IC62. Check the Sample Gain control is okay and the wiring to
A several problems with EII
2003-09-04 by grkh2003
Hi everybody! It s nice to be a member of this forum! I ve just obtained my first Emulator II. It is model 6028 (2 floppies, no HD, not + model) And I have
RE: [emulatorII-list] EII + HD noisy outputs
2003-08-28 by Rob Keeble
Hi, 10K Log Bourns 91A1A-B28-D-10K, Farnell Part Number at www.farnell.com 109-085 You ll need a new knob as well - as the new pot shaft is circular not D.
RE: [emulatorII-list] EII + HD noisy outputs
2003-08-28 by BRANT DURHAM
ROB, I WOULD LIKE TO REPLACE MINE. WHAT IS THE PART NUMBER FOR THE BOURNS POT? THANKS, BRANT ... __________________________________ Do you Yahoo!? Yahoo!
RE: [emulatorII-list] EII + HD noisy outputs
2003-08-28 by Rob Keeble
Hi, Sounds like something is wrong. My EII+HD was fine. I found replacing the VOLUME pot on my EII s with a high quality BOURNS conductive plastic pot improved
EII + HD noisy outputs
2003-08-28 by Kevin Kelley
I have a EII + HD and the outputs pass alot of the hard drive noise. I was wondering if anyone ever addressed this problem with a mod or upgrade? If anyone
Re: [emulatorII-list] EII PS Trimming?
2003-08-12 by kevin kelley
The PSU schematics are in the files section of the home page for this group. or try this link http://groups.yahoo.com/group/Emulator_II/files/. Kevin Kelley
EII PS Trimming?
2003-08-12 by modularmoog
Hi - I m new here and just started the repair of an EII+. Does anyone have any documentation on triming the EII Power Supply? I think that there s a problem
serial number : 152
2003-08-09 by moose
ok, i ve been offered an emulator II serial number 152 (dual floppy version) for a very reasonable price down here near los angeles. if anyone is wanting this
possible new abuser
2003-08-09 by moose
hi, i m moose from a band called alaska highway who re heavily into digital noise. we currently use 4 samplers - e4xt & e4xt ultra with 2 emax ii s - and have
Re: [emulatorII-list] dynamic filters on SP12?
2003-08-02 by Simon Wotton
thanx for the info, rob... shame, i was really excited about the comment on your site, but on the other hand wondering, why there wasn´t anything mentioned in
RE: [emulatorII-list] dynamic filters on SP12?
2003-08-02 by Rob Keeble
Hi, The two SSM2044 filters can be adjusted only in hardware, they are not accessible via the SP-12 Operating System. You can play with trimmers RT5 and RT6 on
dynamic filters on SP12?
2003-08-01 by the_emulatorii
hi all!!! on the emulator-archive i read about dynamic filters on the SP12 - it is said, that two of the filters can be internelly ajusted!!! how can i adjust
RE: [emulatorII-list] PLEASE: can someone help me with setup plans!!!
2003-06-19 by Rob Keeble
Hi, Use SD for EII for the EII (over RS422) and Waters Edge Software SP-12 Librarian for the SP-12 (over MIDI). These will run on a legacy Mac or PowerBook
PLEASE: can someone help me with setup plans!!!
2003-06-16 by the_emulatorii
i am planing to use all of my emu equipment in a seperate computer- environment - meaning, that i want to connect my emulato2 and my sp12turbo with a macintosh
Re: spare-part-situation uncritical???
2003-06-15 by the_emulatorii
i will send your list to him and we´ll see what he can do for the emulator community...!!! :-) i am quite sure, that he meant electronic-spares - only - i
RE: [emulatorII-list] spare-part-situation uncritical???
2003-06-14 by Rob Keeble
Hi, Hard to find EII spares: Power Supplies Any keys, especially Top C Keyboard assembly Casing and base, lettering PCB s Hard Disk Controller (Adaptec 4000B)
Re: [emulatorII-list] spare-part-situation uncritical???
2003-06-13 by mishon66@aol.com
... I need one high C key, we were going to make these but found out the costs of the mold were thousands. Richard at Route 66
spare-part-situation uncritical???
2003-06-13 by the_emulatorii
hey everyone... after long searches i have found quite a few people, who have done - or still do repairs on vintage emu gear. i konow that a repair can be
Re: [emulatorII-list] 3.5 in a EII + HD ?
2003-06-06 by Thomas Mattera
Here is a kit to replace the old 5.25 with a 3.5 . No muss no fuss just put it in. .. Tom http://www.route66studios.com/ Brian wrote:
Re: [emulatorII-list] 3.5 in a EII + HD ?
2003-06-06 by Brian
Hi Kevin, I haven t tried to make a EII+HD boot from a 3½ drive but the EII+HD will boot from the 5.25 floppy if the disc is insertet at bootup. With a
RE: [emulatorII-list] 3.5 in a EII + HD ?
2003-06-04 by Rob Keeble
Hi, Works fine with me. Regards Rob ... From: Kevin Kelley [mailto:xirin6@yahoo.com] Sent: 03 June 2003 14:25 To: emulatorII-list@yahoogroups.com Subject:
3.5 in a EII + HD ?
2003-06-03 by Kevin Kelley
I recently placed a 3.5 drive into my EII + HD and it does not boot from the 3.5 it will try to load but it will just prompt OS version and never complete the
Re: [emulatorII-list] Re: EII Samples on CD
2003-06-02 by 3phase
An old macplus with a zipdrive as bootpartition is a cheap and silent option /(zips stop spinning when not in use. actually is the mac plus the wright age to
Re: EII Samples on CD
2003-06-02 by tonyfacevalue
... samples as ... is Mac ... EII if you ... the ... page... ... 20Diskette ... I am considering going down the Mac option for getting hold of more EII
MIDI Sync - SP12 ???
2003-05-09 by the_emulatorii
i have a question concerning the sync section of my sp12. i would like it to be a slave to my sequencer program (cubase) the sp12 is connected via
MIDI Sync - SP12 ???
2003-05-09 by the_emulatorii
i have a question concerning the sync section of my sp12. i would like it to be a slave to my sequencer program (cubase) the sp12 is connected via
Re: [emulatorII-list] best deal on 4megs of ram for my Emulator III
2003-05-02 by Brian
Hi Greg In order to upgrade your EIII you need the upgrade kit 6084 or 6085 (Emu-systems do not sell these kits anymore) along with the 30 pin sim ram.. You
Re: [emulatorII-list] best deal on 4megs of ram for my Emulator III
2003-05-01 by greg thurman
Thanks Brian for clearing this up, now I need to find out where to purchase this memory or 4 1meg chips? I already have 4 megs with the unit. greg ...
Re: [emulatorII-list] Re: burning EPROMS??? anyone?????
2003-05-01 by mishon66@aol.com
... Simon I have an Eprom burner and I have used it for sometime but I have never heard of this C64 setup. It would have to allow for many different types and
Re: burning EPROMS??? anyone?????
2003-05-01 by the_emulatorii
does anyone have info on this one???? ... for ... socket ... prommer)? ... pc?? ... need?
Re: [emulatorII-list] best deal on 4megs of ram for my Emulator III
2003-05-01 by Brian
Hi Greg The max ram for the EII is 1 Mb devided into 2 banks of 512 kb. The EIII can access 8 Mb in either 256 kb blocks or 1 mb blocks. I sure that the memory
best deal on 4megs of ram for my Emulator III
2003-04-30 by greg thurman
I have a emulator II & III Does any on no if both machines use the same memory chip? Id like to get the best deal on a 4 meg chip for my emulator III. Used or
Emulator II keys
2003-04-30 by kruz@beatbazar.com
Hi all.. I m in need of 3 white keys for my was-dead E II, i m sure that these are the same as the E III (i have an E III too). Do anyone know a place to ask
New Topic
2003-04-30 by Thomas Mattera
Here is a new topic. I recently bought an Emulator IV Classic from an Ebay auction. The backlite is out as are some segments of the display. I was wondering if
burning EPROMS???
2003-04-30 by the_emulatorii
hey here is the new topic! someone is offering me a commodore c64 with some strange device for burning eproms (at least he thinks it is for doing that...) it
Re: SP12 fails!!! - - - why always me :-(
2003-04-30 by the_emulatorii
everything ok - worked great - just like yesterday!!! i have tried all outputs - they work, so it must be the factory eproms failing slowly but surely. if
Re: [emulatorII-list] Re: SP12 fails!!! - - - why always me :-(
2003-04-30 by Simon Wotton
hey rob!!! here is what the former owner of the sp12 had to say to the problem. meanwhile it has worked again: yesterday everything was fine and so i gave it a
RE: [emulatorII-list] Re: SP12 fails!!! - - - why always me :-(
2003-04-29 by Rob Keeble
Hi, First check to see if the problem is on one particular channel (listen to the individual outs with ROM and RAM sounds). If ROM and RAM sounds always cause
Re: SP12 fails!!! - - - why always me :-(
2003-04-29 by the_emulatorii
i have tried it again today... looks like these noisy sounds have now become a permanent error on my sp12. when i switched it on again today, there were the
RE: [emulatorII-list] Re: sp12 to emulator2 and vice versa
2003-04-28 by Rob Keeble
Hi, The EII was based on the Emulator I in terms of sampling rate, etc. Scott and Dave took the opportunity to move up to 12-bits with the SP-12, and then