Marcos Maniacs

Hi guys,

The attached was received from Drew Guild following our conversation
yesterday. I don't know if Jeff  Caraway is still coordinating the screen
acquisitions or if there has been any additional interest recently because
I've been off-line for a few weeks. I responded to Drew to say that the cost
would probably be prohibitively high due to the current known requirement of
only 5 front and 6 rear glass screens. Maybe he'll come back with a better
offer. If I hear anything further, I'll pass it on.

Regards,

Paul Dransfield
3 litre Volvo

-----Original Message-----
From: Drew [mailto:Drew@...]
Sent: September 5, 2002 5:06 PM
To: pauldransfield@iname.com
Subject: Marcos British Sports car glass


This is Drew Guild, WIN Manufacturing, Elmira, NY

I think I talked to you earlier this afternoon. Are you the same?

If you could be more exact the Year, Make and Model that the glass would go
to. Most Models for the glass only last four or five years then they change
the model and the old is obsolete.

The package would be 10 windshields for $7500.00. Ten back glasses for
$7500.00 Again, the backglass would be laminated, not tempered. Money must
be paid up front before any tooling begins.

Tooling includes Mariset template, cutting template, bending fixture,
checking fixture, and silk screen (if required).

Delivery turnaround 45-60 days.

Here's a quick overview of our manufacturing:

At WIN, five generations of participation in the glass industry, has
provided the experience and knowledge which has become the foundation of
advanced laminated products, fabricating practices, and service to our
customers.  Our laminated glass products meet the quality and performance
demands of both the automotive and architectural markets. WIN's
manufacturing operation utilizes state of the art production techniques and
equipment in the fabrication of both flat and curved laminated products.

WIN's Automotive product family (WINVintage, WINSTruck) manufactures
products that meet the replacement, retrofit, specialty, classic, and
hard-to-find requirements.  We are proud to display our WIN logo on
windshields of late model cars, trucks and busses, and early model street
rods and classic autos. These products meet the standards established by the
American National Science Institute (ANSI Z26, AS 1 and 2.)  WIN products
are approved and meet the Federal Motor Vehicle Safety Standard 205, U.S.
Department of Transportation (DOT #381.)  Our certified materials are
procured from suppliers such as DuPont, Solutia, Trosifol, Guardian
Industries, AFG, Visteon and PPG.

WIN has a full line of product offerings to meet the requirements set for
safety, forced entry and, hurricane protection.  WINStorm DuPont SentryGlas®
Plus NOA98-0608.03 and Saflex® HP NOA 02-017.06, also, WINSpec products
comply with the architectural standards established by the Consumer Product
Safety Commission16, CFR 1201, categories one and two, and ANSI Z97.1 and
UL972 et al.  We offer Sheffield and GE Polycarbons that have met the
stringent code requirements of South Florida and other coastal regions.

WIN's Bullet Resistant (WINProtect) products are specially fabricated to
meet our customers' requirements.  WINProtect 35, WINProtect 44 and
WINProtect 30 are cetified by H.P.White NIJ II,IIIA, and III respectively.

Call today for information or to order WIN's quality laminated glass
products.  Let us service your standard product requirement or challenge us
with that special need.

Gratefully yours,

Drew Guild
WIN Manufacturing Sales
1120 Magee St.
Elmira, NY 14901
1-888-935-0111 x124
Fax 607-734-9442
Drew@...
winmfg@...m

Hi Paul and all,
    Your efforts on behalf of the group are greatly appreciated on
the "glass hunt" ........it wouldn't be the end of the world though 
if we had to source them from Britian.
    Paul or Ron ....when is the British show at Bronte , this weekend
or next?
    I have uploaded some pics of my completed frame ...I thought they
 were going to go into my album.......I will try to transfer them 
later.
 Cheers Dave #5577









--- In MarcosManiacs@y..., pauldransfield@i... wrote:
> Hi guys,
> 
> The attached was received from Drew Guild following our conversation
> yesterday. I don't know if Jeff  Caraway is still coordinating the 
screen
> acquisitions or if there has been any additional interest recently 
because
> I've been off-line for a few weeks. I responded to Drew to say that 
the cost
> would probably be prohibitively high due to the current known 
requirement of
> only 5 front and 6 rear glass screens. Maybe he'll come back with a 
better
> offer. If I hear anything further, I'll pass it on.
> 
> Regards,
> 
> Paul Dransfield
> 3 litre Volvo
> 
> -----Original Message-----
> From: Drew [mailto:Drew@w...]
> Sent: September 5, 2002 5:06 PM
> To: pauldransfield@i...
> Subject: Marcos British Sports car glass
> 
> 
> This is Drew Guild, WIN Manufacturing, Elmira, NY
> 
> I think I talked to you earlier this afternoon. Are you the same?
> 
> If you could be more exact the Year, Make and Model that the glass 
would go
> to. Most Models for the glass only last four or five years then they 
change
> the model and the old is obsolete.
> 
> The package would be 10 windshields for $7500.00. Ten back glasses 
for
> $7500.00 Again, the backglass would be laminated, not tempered. 
Money must
> be paid up front before any tooling begins.
> 
> Tooling includes Mariset template, cutting template, bending 
fixture,
> checking fixture, and silk screen (if required).
> 
> Delivery turnaround 45-60 days.
> 
> Here's a quick overview of our manufacturing:
> 
> At WIN, five generations of participation in the glass industry, has
> provided the experience and knowledge which has become the 
foundation of
> advanced laminated products, fabricating practices, and service to 
our
> customers.  Our laminated glass products meet the quality and 
performance
> demands of both the automotive and architectural markets. WIN's
> manufacturing operation utilizes state of the art production 
techniques and
> equipment in the fabrication of both flat and curved laminated 
products.
> 
> WIN's Automotive product family (WINVintage, WINSTruck) manufactures
> products that meet the replacement, retrofit, specialty, classic, 
and
> hard-to-find requirements.  We are proud to display our WIN logo on
> windshields of late model cars, trucks and busses, and early model 
street
> rods and classic autos. These products meet the standards 
established by the
> American National Science Institute (ANSI Z26, AS 1 and 2.)  WIN 
products
> are approved and meet the Federal Motor Vehicle Safety Standard 205, 
U.S.
> Department of Transportation (DOT #381.)  Our certified materials 
are
> procured from suppliers such as DuPont, Solutia, Trosifol, Guardian
> Industries, AFG, Visteon and PPG.
> 
> WIN has a full line of product offerings to meet the requirements 
set for
> safety, forced entry and, hurricane protection.  WINStorm DuPont 
SentryGlas®
> Plus NOA98-0608.03 and Saflex® HP NOA 02-017.06, also, WINSpec 
products
> comply with the architectural standards established by the Consumer 
Product
> Safety Commission16, CFR 1201, categories one and two, and ANSI 
Z97.1 and
> UL972 et al.  We offer Sheffield and GE Polycarbons that have met 
the
> stringent code requirements of South Florida and other coastal 
regions.
> 
> WIN's Bullet Resistant (WINProtect) products are specially 
fabricated to
> meet our customers' requirements.  WINProtect 35, WINProtect 44 and
> WINProtect 30 are cetified by H.P.White NIJ II,IIIA, and III 
respectively.
> 
> Call today for information or to order WIN's quality laminated glass
> products.  Let us service your standard product requirement or 
challenge us

> with that special need.
> 
> Gratefully yours,
> 
> Drew Guild
> WIN Manufacturing Sales
> 1120 Magee St.
> Elmira, NY 14901
> 1-888-935-0111 x124
> Fax 607-734-9442
> Drew@w...
> winmfg@w...

Regards . . . Ron McLeod
1970 Marcos Mantis P8/5858