16 step seq
2011-11-28 by aletropdj
hi there. Its possible turn a a-155 into a 16 step seq with only one a-155? Like tone up or down one octave (or some keys) at the 8th step automatically. There is some module to do that? cheers
Thread
16 step seq
Re: [Doepfer_a100] 16 step seq
2011-11-29 by Florian Anwander
Hello, it is not possible to achieve this with "official" means. If you are skilled in electronics you might modify the A155, to get a 16 step mode. It requires the following changes: Pick Q4 from IC2 (CD4024) pin6 on the controller board Add a pcb with a small logic inverter stage (one transistor, two resistors), which provides this signal Q4 also inverted (I'll call the inverted signal !Q4) The Q4/!Q4-Signals will be used to control the INH-input of the CD4051's on the potentiometer boards and the CD4053's on the trigger board !Q4 selects for the steps 1-8 and Q4 the steps 9-16. If you want to have it switchable, then you need two additional 4053's which select the INH-lines between ground or Q4/!Q4. Florian aletropdj wrote:
Show quoted textHide quoted text
> hi there. > > Its possible turn a a-155 into a 16 step seq with only one a-155? > Like tone up or down one octave (or some keys) at the 8th step automatically. > > There is some module to do that? > > cheers > > > > ------------------------------------ > > Yahoo! Groups Links > > > >
Re: 16 step seq
2011-11-29 by aletropdj
Using the second row of knobs i can make a 16 step seq, but i have to put the jack in and out "a la mano". im looking for a automatic solution --- In Doepfer_a100@yahoogroups.com, "aletropdj" <aletropdj@...> wrote:
Show quoted textHide quoted text
> > hi there. > > Its possible turn a a-155 into a 16 step seq with only one a-155? > Like tone up or down one octave (or some keys) at the 8th step automatically. > > There is some module to do that? > > cheers >
AW: [Doepfer_a100] Re: 16 step seq
2011-11-29 by yahoo@doepfer.de
> Using the second row of knobs i can make a 16 step seq, but i > have to put the jack in and out "a la mano". im looking for a > automatic solution For thhis you may use a VC switch (A-150) which is controlled by a clock divider (A-160). As clock input of the A-160 one of the trigger rows of the A-155 may be used (only step 1 active). Then you have to use the /2 output to control the A-150. But you may even use the same clock as the A-155 clock. Then the /8 output of the A-160 is used to control the A-150. This solution has the advantage that unit #2 of the A-150 can be used to switch even the trigger rows of the A-155. Hope this helps Dieter Doepfer
Re: 16 step seq
2011-11-29 by aletropdj
For example this sequence up and down variation is produced with A-150 and a-160? http://www.youtube.com/watch?v=ZBTsEwNRxe8 --- In Doepfer_a100@yahoogroups.com, <yahoo@...> wrote:
Show quoted textHide quoted text
> > > Using the second row of knobs i can make a 16 step seq, but i > > have to put the jack in and out "a la mano". im looking for a > > automatic solution > > For thhis you may use a VC switch (A-150) which is controlled by a clock > divider (A-160). As clock input of the A-160 one of the trigger rows of the > A-155 may be used (only step 1 active). Then you have to use the /2 output > to control the A-150. But you may even use the same clock as the A-155 > clock. Then the /8 output of the A-160 is used to control the A-150. This > solution has the advantage that unit #2 of the A-150 can be used to switch > even the trigger rows of the A-155. > > Hope this helps > Dieter Doepfer >
Re: [Doepfer_a100] Re: 16 step seq
2011-11-30 by Lars Bröndum
You can use a a-160 and a a-150 to get 16 steps. From the manual: The patch in fig. 6 shows how to use the A-155 as a 16-step sequencer with one single analog CV row. What’s needed are the Clock Divider A-160 (output /8) and the two voltage-controlled swit- ches in the A-150 VCS module. With every eight clock pulses, the A-150 switches between the two trigger and analog CV rows, so that there’s now a 16-step trigger and CV sequence avai- lable at the outputs of the A-150. Good luck! /Lars Bröndum On 29 nov 2011, at 14:29, "aletropdj" <aletropdj@yahoo.com> wrote: > Using the second row of knobs i can make a 16 step seq, but i have to put the jack in and out "a la mano". im looking for a automatic solution > > --- In Doepfer_a100@yahoogroups.com, "aletropdj" <aletropdj@...> wrote:o > > > > hi there. > > > > Its possible turn a a-155 into a 16 step seq with only one a-155? > > Like tone up or down one octave (or some keys) at the 8th step automatically. > > > > There is some module to do that? > > > > cheers > > > > [Non-text portions of this message have been removed]
Re: 16 step seq
2011-11-30 by aletropdj
I need 2 a-150? but a-150 its dual. how i can control de voltage to make this tone up or down? its fixed like 1v/oct or i can adjust? Thanks all. --- In Doepfer_a100@yahoogroups.com, Lars Bröndum <lahebr2000@...> wrote:
Show quoted textHide quoted text
> > You can use a a-160 and a a-150 to get 16 steps. > > From the manual: > The patch in fig. 6 shows how to use the A-155 as a 16-step sequencer with one single analog CV row. Whatâs needed are the Clock Divider A-160 (output /8) and the two voltage-controlled swit- ches in the A-150 VCS module. > With every eight clock pulses, the A-150 switches between the two trigger and analog CV rows, so that thereâs now a 16-step trigger and CV sequence avai- lable at the outputs of the A-150. > > Good luck! > > /Lars Bröndum > > On 29 nov 2011, at 14:29, "aletropdj" <aletropdj@...> wrote: > > > Using the second row of knobs i can make a 16 step seq, but i have to put the jack in and out "a la mano". im looking for a automatic solution > > > > --- In Doepfer_a100@yahoogroups.com, "aletropdj" <aletropdj@> wrote:o > > > > > > hi there. > > > > > > Its possible turn a a-155 into a 16 step seq with only one a-155? > > > Like tone up or down one octave (or some keys) at the 8th step automatically. > > > > > > There is some module to do that? > > > > > > cheers > > > > > > > > > > [Non-text portions of this message have been removed] >
Re: 16 step seq
2011-12-02 by aletropdj
anyone? --- In Doepfer_a100@yahoogroups.com, "aletropdj" <aletropdj@...> wrote:
Show quoted textHide quoted text
> > > > I need 2 a-150? but a-150 its dual. > how i can control de voltage to make this tone up or down? its fixed like 1v/oct or i can adjust? > > Thanks all. > > > > > > > --- In Doepfer_a100@yahoogroups.com, Lars Bröndum <lahebr2000@> wrote: > > > > You can use a a-160 and a a-150 to get 16 steps. > > > > From the manual: > > The patch in fig. 6 shows how to use the A-155 as a 16-step sequencer with one single analog CV row. Whatâs needed are the Clock Divider A-160 (output /8) and the two voltage-controlled swit- ches in the A-150 VCS module. > > With every eight clock pulses, the A-150 switches between the two trigger and analog CV rows, so that thereâs now a 16-step trigger and CV sequence avai- lable at the outputs of the A-150. > > > > Good luck! > > > > /Lars Bröndum > > > > On 29 nov 2011, at 14:29, "aletropdj" <aletropdj@> wrote: > > > > > Using the second row of knobs i can make a 16 step seq, but i have to put the jack in and out "a la mano". im looking for a automatic solution > > > > > > --- In Doepfer_a100@yahoogroups.com, "aletropdj" <aletropdj@> wrote:o > > > > > > > > hi there. > > > > > > > > Its possible turn a a-155 into a 16 step seq with only one a-155? > > > > Like tone up or down one octave (or some keys) at the 8th step automatically. > > > > > > > > There is some module to do that? > > > > > > > > cheers > > > > > > > > > > > > > > > > [Non-text portions of this message have been removed] > > >