Re: [AN1x] Re: V1.04 for AN1X?
2014-02-12 by Jeff
Good idea indeed, but a few years ago the same idea has been rejected by the moderators because of possible copyright problems. Cheers. J.F. ... Ce courrier
Messages
Browse messages
Page 11 of 268 · 13386 messages matched
Re: [AN1x] AN1X Pots
2014-02-12 by Jeff
Try some electronic contact cleaner like KF or similar sold in every DIY electronics shop. Spray it inside the pot, rotate it 10 - 20 times, wipe out the
Re: [AN1x] Re: V1.04 for AN1X?
2014-02-12 by Narfman96 - Narfland Studio
The LH531024 is the mask ROM OTP chip. The eprom equivalent should be the 27C1024. These eproms are readily available on Ebay. Does anyone have a picture
Re: [AN1x] Re: V1.04 for AN1X?
2014-02-12 by Vadim Nazmiev
Hi, Fran the chip used in An1x for OS is lh531024- It s hard to find nowdays. So if you get it let me know please. regard, Vadim
Re: [AN1x] Re: V1.04 for AN1X?
2014-02-12 by Bruno
Maybe it would be a good idea to put the file in the Files section? Thanks ;-)
AN1X Pots
2014-02-12 by <cbright9@...>
Hi all, My 6th pot is malfunctioning. Only when I push, hold and rotate does the value change. And its not a smooth change, Its pretty erratic. Anyone have
Re: [AN1x] Re: V1.04 for AN1X?
2014-02-12 by Narfman96 - Narfland Studio
Vadim, Thank you for the file! The file you sent is a 1mb file. This means that the eprom must be a 27C040 or 27C4001 4096k chip. These eproms are more
Re: V1.04 for AN1X?
2014-02-11 by <v.nazmiev@...>
Fran, check your email But the Rom chip used in AN1x is not the same as in Rm1x as far as I know. Chip used in Rm1x is still available and cheap. But I didn t
RE: An200: How to get filter and AMW track together?
2014-02-10 by <oliverb@...>
And so it is! I am still hung up on looking for patch routes I guess! Thanks for being so gracious in answering my blindingly stupid question! Bruce
RE: An200: How to get filter and AMW track together?
2014-02-09 by <danielesamas@...>
the filter for the rhythm section is simply applied using cutoff and resonance after selecting one of 3 drum tracks!
RE: An200 Hidden parameters on panel
2014-02-09 by <danielesamas@...>
Hi, very good post to encourage the discovering of our synth-beast. My advice for advanced users is to tweak even more parameters using XGWorks with AN200
An200 Hidden parameters on panel
2014-02-09 by <oliverb@...>
Here s a link to a short cheat sheet on the hidden or obscured parameters available from the front panel of the An200.
RE: An200: How to get filter and AMW track together?
2014-02-09 by <oliverb@...>
I m not, and was beginning to suspect that was the only way. Thanks for the input! Bruce
RE: An200: How to get filter and AMW track together?
2014-02-09 by <tom.cuyt@...>
Are you using the editor? A lot of things can only be done in that.
An200: How to get filter and AMW track together?
2014-02-08 by <oliverb@...>
Hi everyone; I am probably missing something obvious here. On the AN200, how do I apply the filter to the AMW rhythm tracks, as the literature says I can? I
Re: [AN1x] V1.04 for AN1X?
2014-02-07 by chiro973@...
I bought mine from Yamaha ... From: nelson ricardo fdt To: AN1x-list@yahoogroups.com Sent: Friday, January 31, 2014 9:37:15 AM
impedance
2014-02-07 by <jim.alciere@...>
http://en.wikipedia.org/wiki/Line_level
RE: effects
2014-02-06 by <denis_mathys2001@...>
I ve been using my AN1X with a headphone only for one year and I have to admit that the reverbs do not sound very nice. Pluging it in my VS880EX with a reverb
RE: [AN1x] V1.04 for AN1X?
2014-01-31 by <nelson.ricardo_fdt@...>
Yamaha still selling this chips these days? My AN1x rom version is 1.02.
RE: [AN1x] V1.04 for AN1X?
2014-01-31 by <nelson.ricardo_fdt@...>
Yamaha still selling this chips these days? My AN1x rom version is 1.02.
Re: [AN1x] RE: Low volume output
2014-01-31 by <william.bromell@...>
What does it being a line level output have to do with it s impedance? Either way, I tried the instrument input and it didn t make any difference. Next I ll
Re: V1.04 for AN1X?
2014-01-31 by chris22443366
... I had a similar issue with my RM1x, but some very helpful members of the yahoo group, uploaded a bin file into the files area. Another member offered to
[AN1x] V1.04 for AN1X?
2014-01-31 by chiro973@...
I got one from Yamaha
Re: [AN1x] V1.04 for AN1X?
2014-01-31 by jasonic
I think you need a new rom chip to do this update. See this thread: http://www.yamahaforums.co.uk/forum/viewtopic.php?f=9&t=4013 good luck let us know if you
V1.04 for AN1X?
2014-01-29 by <narfman96@...>
Does anyone know where the V1.04 eprom bin file can be found. I have a friend who has requested this update but I m having problems finding the file. Thanks
Re: [AN1x] RE: Low volume output
2014-01-19 by Jeff
... No. It s a line level output. Try the other (470 k) input, it should be OK. Cheers. J.F. ... Ce courrier électronique ne contient aucun virus ou logiciel
RE: Low volume output
2014-01-18 by <william.bromell@...>
My cables are cheap Hosa TS to XLR, so it s possible they re the culprit; I ll try some different unbalanced cables when I get the chance. However, there s no
RE: Low volume output
2014-01-18 by <william.bromell@...>
The interface (RME Babyface) line/mic inputs have an input impedance of 2 k, if that s what you were wondering, and there s an instrument input on the side
Re: [AN1x] RE: Low volume output
2014-01-18 by achtung_999
Are your cables soldered the right way? Do you notice lack of bass in the sound in ableton? Compare between the Ableton version and the headphone out on the
Re: [AN1x] RE: Low volume output
2014-01-18 by jammie
being a new card and balanced i would say its a 10k balanced source dont know what the an1x output impedance is but impedance miss match can cause volume
Re: [AN1x] RE: Low volume output
2014-01-18 by Jeff
... It depends on the headphones impedance, the phones output can find it hard with low impedance phones. For your imput level problem it could be the same :
RE: Low volume output
2014-01-18 by <william.bromell@...>
Something else to note: When I m programming with headphones, the volume has to be about 2/3 to all the way up in order for me to get a strong signal. Does
RE: Low volume output
2014-01-17 by <william.bromell@...>
The interface can handle unbalanced signals. I know almost synths are unbalanced, and it hasn t had problems with any others before this. According to the
RE: Low volume output
2014-01-17 by <william.bromell@...>
I just looked through the manual, and didn t see anything related to a master volume control. There was master tune, transpose, and velocity. Is it possible
Re: [AN1x] Low volume output
2014-01-17 by jammie
its a +4 balanced input that your -10dbu an1x is driving as an unbalanced signal so it will be seen as a low level your interface should be able to switch from
Re: [AN1x] Low volume output
2014-01-17 by Jeff
... Hi William ! i don t think so : supply troubles would more likely cause software crashes. Cheers. J.F. ... Ce courrier électronique ne contient aucun
[AN1x] Low volume output
2014-01-17 by Nate King
do you have the volume turned up the edit section? I forget exactly where it is, but in the soft buttons over on the right, there s a setting for master
Low volume output
2014-01-17 by <william.bromell@...>
When connected to my interface (line level inputs), I have to boost AN1x by around 6 - 12 dB in order to get a strong signal. (I do this in Ableton, not via
effects
2014-01-16 by <jim.alciere@...>
I recorded a lead using one of Richy s patches, a female choir patch, then took a free VST plugin that purported to sound like a Marshall stack. A very
RE: 16 more patches posted
2014-01-03 by <danielesamas@...>
Hi, you re right, I made a mistake about AN200 file loading; .ANS can be loaded of course! Thank you for your presets. Dan
RE: 16 more patches posted
2014-01-02 by <jim.alciere@...>
Thank you Jimmy
RE: 16 more patches posted
2014-01-02 by <uralmoto2001@...>
I converted my PLG banks to .an1 (using an1x editor). You will find them in the an1x voices folder. I had an1x edit on my old computer, and just installed it
Re: 16 more patches posted
2014-01-02 by derek192603
Hi, A registered copy of an.factory (www.xfactory-librarians.co.uk) can convert between all of the varias AN1x, PLG150-AN and AN200 file formats It will also
RE: 16 more patches posted
2014-01-02 by <danielesamas@...>
Hi, it would be great to have the patches converted in .AN1 format and uploaded here for AN200 players like me. Someone can do it? Otherwise we can t convert
16 more patches posted
2013-12-29 by <uralmoto2001@...>
I posted 16 more patches in the PLG150AN voices folder. They are patches 27-42 in my Bank 2 zip file. (For some reason, when I tried to delete my old bank 2
Re: [AN1x] osc sync
2013-12-21 by jammie
its based on analog type fm and not digital fm so there are no operators its just frequency modulation of oscilator like on the prophet 5 which its based on as
Re: [AN1x] osc sync
2013-12-21 by jammie
on the an1x they also added the feedback as used on the minimoog where the vca output is feed back to the mixer input adding distortion it also has the
Re: [AN1x] osc sync
2013-12-21 by jammie
to produce a sin wave on the an1x you need to use the edge waveshaper which rounds off the edges of the saw wave ... From: jammie To: AN1x-list@yahoogroups.com
Re: [AN1x] osc sync
2013-12-21 by jammie
where does he get the sin wave from on page 61 it tells you the waves available when vco1 is set to not sync you have available saw pulse saw2 and mix of
Re: [AN1x] osc sync
2013-12-21 by jammie
when in sync mode osc 1 becomes a dual osc with master and slave osc what ever the master osc is set the slave osc waveform is set the same but resets on the