Maybe you mean attached picture?
Sorry for attaching to all other members, but it's not too big, so I think
it's ok...
You're both right, I just want to add:
It's not easy to remove the potis by soldering, maybe you have to cut the
legs. But as you cannot measure the resistance in-circuit and as you may
rotate the pots while removing them, it would be helpful to mark the
original position with a pen or something before starting your destroying
work. Then you can find the correct position again for measuring after
removing.
The constant resistors are exactly the same as the origin postition of the
pots - that's the factory position!
(Maybe you need more than one for each to meet the exact value. Or try to
measure some cheap ones: because of their tolerances there may be one that
fits best to your requested value. For example 485 ohm is not usual, but
you'll propably find a 470-named one that will fit to 485.
Good luck!
If you have further questions you can contact me.
If you have destroyed your headphone or amplifier or loudspeakers or even
your ears, then you know to be careful with "resonance" using the moog
slayer modification for the next time ....
Regards,
Olaf
----- Original Message -----
From: <hockinfinger@...>
To: <korgpolyex@yahoogroups.com>
Sent: Tuesday, January 27, 2004 8:57 PM
Subject: [korgpolyex] Re: Moogslayer question
> You'll probably need to take them out of the circuit to measure them.
> Pots come in a few different configurations. The best way to tell the
> value of a pot is to measure it with your ohmmeter 3 ways: 1-2, 2-3,
> and 1-3. The pair with the greatest resistance is the actual value of
> the pot. That is essentially a fixed resistance between those 2 pins,
> the third pin connects a slider which varies the resistance between
> it and the other two pins.
> Looking at the photo, it seems as if the pin which connects the
> slider on each pot(the original ones on the circuit board) was
> bridged to one end of the fixed value. I wonder if the intent of
> placing a fixed resitor in place of the pots was to use their factory
> set value, or the max value? Anyone have any ideas?
>
>
>
> --- In korgpolyex@yahoogroups.com, reidar@j... wrote:
> >
> > Hey all,
> >
> > I got the Moogslayer info about a year ago, and now I've finally
> got around
> > to doing something about it. I dug out the docs that I downloaded,
> and
> > apart from the stuff from the 'official' moogslayer site (
> > http://synthmod.net/korg/moog_slayer), I've got a hand-drawn
> picture from
> > someone who has added a switch so that the moogslayer can be
> switched out,
> > and it returns to the factory settings.
> >
> > My problem is that I can't remember where I got that picture, and I
> can't
> > find it on the net, and I have a question about it.
> >
> > So I'll ask the question here - maybe one of you has done this mod.
> >
> > The 'extended' moogslayer has two resistors that replace the pots
> VR2 and
> > VR5, in the 'switched-out' position, so the moogslayer mods are out
> of the
> > circuit. The instructions say to use resistors the same value as
> the two
> > pots, "which may be different on each single Poly800". My
> electronics
> > knowledge doesn't go far beyond using a soldering iron, so I'm not
> sure how
> > to ascertain the value of the pots. Can I just measure the
> resistance
> > between two of the three pins? Which two pins? Do I need to
> desolder them
> > first?
> >
> > Any help would be greatly appreciated. I can email the photos, but
> I'm
> > reluctant to put it in the photos section until I find out where it
> comes
> > from, and if the mod is reliable.
> >
> > Cheers,
> > Reidar
>
>
>
>
>
> Yahoo! Groups Links
>
> To visit your group on the web, go to:
> http://groups.yahoo.com/group/korgpolyex/
>
> To unsubscribe from this group, send an email to:
> korgpolyex-unsubscribe@yahoogroups.com
>
> Your use of Yahoo! Groups is subject to:
> http://docs.yahoo.com/info/terms/
>
>
>