Discussion about the Korg PolySix synthesizer

in the last month we are talking about an lfo issue that sounds like 
a distortion. and voila, now i get the same problem. really strange. 
if i adjust the phaser/chorus speed, i get strange sounds and i'm 
unable to restore it back. and from this point its impossible to 
disable the lfo level too. some sliders are doing really strange 
things (sustain adjusts cutoff eg). 
mmh so far it can't be the IC30/31 problem, since i already replaced 
it. (and i changed it again, to check if something is damaged again)
did someone found a solution for this problem?  


--- In PolySix@yahoogroups.com, "BrainSlayer" <brainslayer@c...> 
wrote:
> if you trigger the lfo to frequency oscillation and adjust the lfo 
frequency to maximum, you will get also very heavy distorted sounds. 
and that sounds like the IC30/31 problem. but i discovered also 
other issues that effects the lfo. the cables from the board to the 
top the control board are very short. sometimes if i open my case 
they lost the contact and i get strange effects too
>   ----- Original Message ----- 
>   From: toorglick 
>   To: PolySix@yahoogroups.com 
>   Sent: Monday, July 19, 2004 5:58 PM
>   Subject: [PolySix] Re: Son of a b****
> 
> 
>   Yeah, it sounds more like the or *a* LFO gone haywire, but at a 
>   frequency where it sounds more like distortion.  
> 
>   The only other conclusion I can come to is that I fried IC30 
when 
>   installing the new chip.  The electronics store I go to didn't 
have 
>   any 14 pin IC sockets.  Maybe I'll stop by Radio Shack to see if 
they 
>   do.  That and the initial I repairs I made weren't robust enough 
or 
>   didn't catch everything breaking down.
> 
>   Fortunately I have five more 74LS08's left!
> 
>   One thing I noticed while checking traces and other connections 
on 
>   the board is that not all of the connections read the same 
value, 
>   though they all fall within certain value groups, as it were.  
Would 
>   anyone mind telling me what I should be seeing?
> 
>   Also, can anyone tell me what R17 is?  On the schem it's 
called "RKC 
>   1/8 88 10k".  What does it do?  Can I get a new one readily?  
> 
>   The reason I ask is because I'm thinking about starting from 
scratch; 
>   removing the jumps I made before; replacing ICs 30 & 31 and 
possibly 
>   R17.  Since I've had my Polysix and have seen pictures of 
others' 
>   KLM367s it looks as though mine was/is in pretty rough shape.  A 
lot 
>   of the solder points above the battery area are dull, and some 
have 
>   visibly corroded.  I've checked them all, include a lot of what-
are-
>   they-called? vias? (the areas where the path switches from the 
bottom 
>   to the top and vice-versa) and all check out, but some 
look "bad."
> 
>   Anyway, that's my story.  I really prefer to be playing instead 
of 
>   fixing, but nothing sounds like a *real* Polysix and thus I'm 
>   addicted.  Any input is appreciated.
> 
> 
>   --- In PolySix@yahoogroups.com, "BrainSlayer" <brainslayer@c...> 
>   wrote:
>   > sounds like a lfo problem
>   >   ----- Original Message ----- 
>   >   From: reidar@j... 
>   >   To: PolySix@yahoogroups.com 
>   >   Sent: Monday, July 19, 2004 1:47 AM
>   >   Subject: Re: [PolySix] Son of a b****
>   > 
>   > 
>   > 
>   >   That sounds like what my P6 is doing too - like the mod 
wheel is 
>   fully on.
>   >   Everything is 'bubbling'.  I have found that the PWM width 
>   control seems to
>   >   have the best effect on it, but also, if I leave the P6 
switched 
>   on for an
>   >   hour or so, it goes away.  I'm not an electronics-type, so I 
>   really don't
>   >   have a clue, but the fact that it goes away (usually) after 
a 
>   long warm-up
>   >   might mean something to some of you?
>   > 
>   >   Reidar
>   > 
> 
> 
> 
> 
>   PolySix "Digiest" Page: http://www.acc.umu.se/~amber/Poly6 
> 
> 
>         Yahoo! Groups Sponsor 
>               ADVERTISEMENT
>              
>        
>        
> 
> 
> -------------------------------------------------------------------
-----------
>   Yahoo! Groups Links
> 
>     a.. To visit your group on the web, go to:
>     http://groups.yahoo.com/group/PolySix/
>       
>     b.. To unsubscribe from this group, send an email to:
>     PolySix-unsubscribe@yahoogroups.com
>       
>     c.. Your use of Yahoo! Groups is subject to the Yahoo! Terms 
of Service. 
> 
> 
> 
> [Non-text portions of this message have been removed]