Yahoo Groups archive
Thread
2004-02-07 by gustavo_sagasti
Hi: I have a Wiggler from Macraigor that came with a Triscend (8051 embedded + FPGA) SCoC Dev Kit. Does someone know if it would be compatible (may be configuring an internal jumper...) with Crosswork (from Rowley) or Keil Debugger? Thank in advance... Gus
2004-02-07 by Leon Heller
----- Original Message -----
From: "gustavo_sagasti" <gustavo_sagasti@...> To: <lpc2100@yahoogroups.com> Sent: Saturday, February 07, 2004 11:08 PM Subject: [lpc2100] Wiggler > Hi: > > I have a Wiggler from Macraigor that came with a Triscend (8051 > embedded + FPGA) SCoC Dev Kit. > Does someone know if it would be compatible (may be configuring an > internal jumper...) with Crosswork (from Rowley) or Keil Debugger? Are you sure it was a Triscend 8051? They also do an ARM system, which comes with a Wiggler, IIRC. Or, perhaps they have JTAG on the 8051, also. I think Triscend was recently bought by ARM, BTW. It will probably be OK. The other Wiggler versions (they all have the same basic PCB) are for PowerPC etc. You could just try it and see if it works. Leon -- Leon Heller, G1HSM Email: aqzf13@... My low-cost Philips LPC210x ARM development system: http://www.geocities.com/leon_heller/lpc2104.html
2004-10-27 by theeuwke
Hi Everyone, I build myself a wiggler, I used the schematic from sobellinni, but I used a 74HC244N, put 5v on the VRef. I configured my board, but OCD Commander says the cable is disconnected, ocdlibtool connect on a certain configuration of the board (but actually not the right one) but I get al kinds of errors. Is there something wrong with the schematic, do I use the wrong chip/voltage, or do I use the wrong software? Regards, Theeuwke
2004-10-27 by Leon Heller
>From: "theeuwke" <theeuwke@...> >Reply-To: lpc2000@yahoogroups.com >To: lpc2000@yahoogroups.com >Subject: [lpc2000] Wiggler >Date: Wed, 27 Oct 2004 07:01:48 -0000 > > > >Hi Everyone, > >I build myself a wiggler, I used the schematic from sobellinni, but >I used a 74HC244N, put 5v on the VRef. I configured my board, but >OCD Commander says the cable is disconnected, ocdlibtool connect on >a certain configuration of the board (but actually not the right >one) but I get al kinds of errors. Is there something wrong with the >schematic, do I use the wrong chip/voltage, or do I use the wrong >software? Try my schematic and PCB design: jtag.zip That works OK for me. Leon
2004-10-27 by theeuwke
--- In lpc2000@yahoogroups.com, "Leon Heller" <leon_heller@h...> wrote: > > > > >From: "theeuwke" <theeuwke@y...> > >Reply-To: lpc2000@yahoogroups.com > >To: lpc2000@yahoogroups.com > >Subject: [lpc2000] Wiggler > >Date: Wed, 27 Oct 2004 07:01:48 -0000 > > > > > > > >Hi Everyone, > > > >I build myself a wiggler, I used the schematic from sobellinni, but > >I used a 74HC244N, put 5v on the VRef. I configured my board, but > >OCD Commander says the cable is disconnected, ocdlibtool connect on > >a certain configuration of the board (but actually not the right > >one) but I get al kinds of errors. Is there something wrong with the > >schematic, do I use the wrong chip/voltage, or do I use the wrong > >software? > > Try my schematic and PCB design: jtag.zip > > That works OK for me. > > Leon uh, ok, but the ondly diference is 1 extra resister, but I will put it on my board. And, I use a BC576C for the Transistor. What do you use for voltage on the 74HC244 ? (pin 20)
2004-10-27 by Leon Heller
>From: "theeuwke" <theeuwke@...> >Reply-To: lpc2000@yahoogroups.com >To: lpc2000@yahoogroups.com >Subject: [lpc2000] Re: Wiggler >Date: Wed, 27 Oct 2004 09:43:21 -0000 > > > >--- In lpc2000@yahoogroups.com, "Leon Heller" <leon_heller@h...> >wrote: > > > > > > > > >From: "theeuwke" <theeuwke@y...> > > >Reply-To: lpc2000@yahoogroups.com > > >To: lpc2000@yahoogroups.com > > >Subject: [lpc2000] Wiggler > > >Date: Wed, 27 Oct 2004 07:01:48 -0000 > > > > > > > > > > > >Hi Everyone, > > > > > >I build myself a wiggler, I used the schematic from sobellinni, >but > > >I used a 74HC244N, put 5v on the VRef. I configured my board, but > > >OCD Commander says the cable is disconnected, ocdlibtool connect >on > > >a certain configuration of the board (but actually not the right > > >one) but I get al kinds of errors. Is there something wrong with >the > > >schematic, do I use the wrong chip/voltage, or do I use the wrong > > >software? > > > > Try my schematic and PCB design: jtag.zip > > > > That works OK for me. > > > > Leon > >uh, ok, but the ondly diference is 1 extra resister, but I will put >it on my board. And, I use a BC576C for the Transistor. It should be OK then. What do you >use for voltage on the 74HC244 ? (pin 20) It should be supplied from pins 1 and 2 on the 20 way header that connects to the target board (3.3V). Leon
2004-10-27 by theeuwke
--- In lpc2000@yahoogroups.com, "Leon Heller" <leon_heller@h...> wrote: > > > > >From: "theeuwke" <theeuwke@y...> > >Reply-To: lpc2000@yahoogroups.com > >To: lpc2000@yahoogroups.com > >Subject: [lpc2000] Wiggler > >Date: Wed, 27 Oct 2004 07:01:48 -0000 > > > > > > > >Hi Everyone, > > > >I build myself a wiggler, I used the schematic from sobellinni, but > >I used a 74HC244N, put 5v on the VRef. I configured my board, but > >OCD Commander says the cable is disconnected, ocdlibtool connect on > >a certain configuration of the board (but actually not the right > >one) but I get al kinds of errors. Is there something wrong with the > >schematic, do I use the wrong chip/voltage, or do I use the wrong > >software? > > Try my schematic and PCB design: jtag.zip > > That works OK for me. > > Leon Mmm, it resets good now, but I have still some problems. I put some little program on the board to enable the JTAG port (i have to use the second), but when I try to do something in GDB it is still complaining that the processor is still running. 2nd; OCD Commander is still saying he can't find a wiggler. Here's some information about the configuration of my board: http://www.ashling.com/support/lpc2000/knowledge_base.html I use this board: http://www.ashling.com/datasheets/DS266-EvKitLPC2000.html Regards, Theeuwke
2004-10-27 by Leon Heller
>From: "theeuwke" <theeuwke@...> >Reply-To: lpc2000@yahoogroups.com >To: lpc2000@yahoogroups.com >Subject: [lpc2000] Re: Wiggler >Date: Wed, 27 Oct 2004 11:14:37 -0000 > > > >--- In lpc2000@yahoogroups.com, "Leon Heller" <leon_heller@h...> >wrote: > > > > > > > > >From: "theeuwke" <theeuwke@y...> > > >Reply-To: lpc2000@yahoogroups.com > > >To: lpc2000@yahoogroups.com > > >Subject: [lpc2000] Wiggler > > >Date: Wed, 27 Oct 2004 07:01:48 -0000 > > > > > > > > > > > >Hi Everyone, > > > > > >I build myself a wiggler, I used the schematic from sobellinni, >but > > >I used a 74HC244N, put 5v on the VRef. I configured my board, but > > >OCD Commander says the cable is disconnected, ocdlibtool connect >on > > >a certain configuration of the board (but actually not the right > > >one) but I get al kinds of errors. Is there something wrong with >the > > >schematic, do I use the wrong chip/voltage, or do I use the wrong > > >software? > > > > Try my schematic and PCB design: jtag.zip > > > > That works OK for me. > > > > Leon > >Mmm, it resets good now, but I have still some problems. I put some >little program on the board to enable the JTAG port (i have to use >the second), but when I try to do something in GDB it is still >complaining that the processor is still running. 2nd; OCD Commander >is still saying he can't find a wiggler. Here's some information >about the configuration of my board: >http://www.ashling.com/support/lpc2000/knowledge_base.html >I use this board: >http://www.ashling.com/datasheets/DS266-EvKitLPC2000.html Have a look at these notes of mine: http://www.geocities.com/leon_heller/lpc2104.html Check on your Ashling board that DBGSEL and TRST are tied high and the LPC bootloader is disabled (P0.14 high). Leon
2004-10-27 by leon_heller
--- In lpc2000@yahoogroups.com, "Leon Heller" <leon_heller@h...> wrote: Something else I just remembered: you might have the interface speed set too fast, try slowing it down. The speed seems to depend on the construction; mine works faster than a genuine Wiggler, probably because I took more care with the PCB layout. Leon
2004-10-27 by theeuwke
--- In lpc2000@yahoogroups.com, "leon_heller" <leon_heller@h...> wrote: > > --- In lpc2000@yahoogroups.com, "Leon Heller" <leon_heller@h...> > wrote: > > Something else I just remembered: you might have the interface speed > set too fast, try slowing it down. The speed seems to depend on the > construction; mine works faster than a genuine Wiggler, probably > because I took more care with the PCB layout. > > Leon I tried al the speed settings, no luck. I Just putted a scope on it, Result when i connect with ocdremote: nRST: pull up TDO : pull down TCK : some data i think TMS : clock TDI : nothing TRST = HIGH DBGSEL: LOW! - > put 3.3 on it?
2004-10-27 by Leon Heller
-- Leon Heller, G1HSM Tel: +44 1424 423947 Email: aqzf13 at dsl dot pipex dot com WWW: http://www.geocities.com/leon_heller >From: "theeuwke" <theeuwke@...> >Reply-To: lpc2000@yahoogroups.com >To: lpc2000@yahoogroups.com >Subject: [lpc2000] Re: Wiggler >Date: Wed, 27 Oct 2004 13:59:38 -0000 > > > >--- In lpc2000@yahoogroups.com, "leon_heller" <leon_heller@h...> >wrote: > > > > --- In lpc2000@yahoogroups.com, "Leon Heller" <leon_heller@h...> > > wrote: > > > > Something else I just remembered: you might have the interface >speed > > set too fast, try slowing it down. The speed seems to depend on >the > > construction; mine works faster than a genuine Wiggler, probably > > because I took more care with the PCB layout. > > > > Leon > >I tried al the speed settings, no luck. > >I Just putted a scope on it, Result when i connect with ocdremote: >nRST: pull up >TDO : pull down >TCK : some data i think >TMS : clock >TDI : nothing > >TRST = HIGH >DBGSEL: LOW! - > put 3.3 on it? That looks like the cause of the problem, DBGSEL should be high to enable JTAG debugging. It has an internal pulldown resistor. Leon
2004-10-27 by ian48harry
Also remember to disable the on-board debugger. Ian --- In lpc2000@yahoogroups.com, "Leon Heller" <leon_heller@h...> wrote: > > > > > -- > Leon Heller, G1HSM Tel: +44 1424 423947 > Email: aqzf13 at dsl dot pipex dot com > WWW: http://www.geocities.com/leon_heller > > > > > >From: "theeuwke" <theeuwke@y...> > >Reply-To: lpc2000@yahoogroups.com > >To: lpc2000@yahoogroups.com > >Subject: [lpc2000] Re: Wiggler > >Date: Wed, 27 Oct 2004 13:59:38 -0000 > > > > > > > >--- In lpc2000@yahoogroups.com, "leon_heller" <leon_heller@h...> > >wrote: > > > > > > --- In lpc2000@yahoogroups.com, "Leon Heller" <leon_heller@h...> > > > wrote: > > > > > > Something else I just remembered: you might have the interface > >speed > > > set too fast, try slowing it down. The speed seems to depend on > >the > > > construction; mine works faster than a genuine Wiggler, probably > > > because I took more care with the PCB layout. > > > > > > Leon > > > >I tried al the speed settings, no luck. > > > >I Just putted a scope on it, Result when i connect with ocdremote: > >nRST: pull up > >TDO : pull down > >TCK : some data i think > >TMS : clock > >TDI : nothing > > > >TRST = HIGH > >DBGSEL: LOW! - > put 3.3 on it? > > That looks like the cause of the problem, DBGSEL should be high to enable
> JTAG debugging. It has an internal pulldown resistor. > > Leon
2004-10-27 by johnnorgaard2003
Hi Have you checked your Parallelport settings. Only EPP mode will do with wiggler, not ECP mode. best regards John