Thanks for the sugestion about patch corruption, i pulled all the
batteries out and let it sit a bit, put the batteries back in and
reloaded the patch .wav
phew, all is good now in analogueland. I'm gonna chalk it up to
static and keep my fingers on the outside of the keyboard for a bit.
Thanks, (I'm a spazz)
--- In korgpolyex@yahoogroups.com, "Funky Monkey"
<funkymonkey3.14@...> wrote:
>
> yep reloaded patches (good) and tested midi output via midi-ox, see
11 p on
> startup
>
>
>
> >From: Marcus Wilson <JB@...>
> >Reply-To: korgpolyex@yahoogroups.com
> >To: korgpolyex@yahoogroups.com
> >Subject: Re: [korgpolyex] Re: Drat -- foiled again, value for D2
needed, if
> >any?
> >Date: Mon, 24 Sep 2007 08:26:46 +0800
> >
> >faint static after a key sounds to me like corrupted patches,
> >have you tried re-loading factory presets?
> >
> >do you see 11 P on your display?
> >
> >best regards,
> >
> >Marcus Wilson
> >On 24/09/2007, at 4:15 AM, funkymonkeypeter wrote:
> >
> >>Tabernack, "is another problem" is true. I have failed spectacularly
> >>in my attempt to do the moogslayer mod. I did the straight pot
> >>transfer from vr5 and vr2 to the front pannel with a factory/ mod
> >>switch as per the olaf-nv "schematic" in photos. That worked fine,
> >>but i must have miss-wired something when i attempted to do the full
> >>moog slayer mod. No output except for very faint static when pressing
> >>a key that continues for about a second after releasing the key, even
> >>after returning everything to before any changes. While pulling out
> >>the changes I did get one tone while touching with my finger one of
> >>the wires that went to VR5 that would change when moving the joystick
> >>downward. The diode I thought was smoked was fine. The only tools i
> >>have at my disposal are a decent multimeter with Hz measurement and a
> >>soldering iron. Is there any hope? Assume that i sent the 4v dc
> >>straight into any of the other connections ground, VR5 or VR2. (next
> >>time i will use different colored wires). All other functions work
> >>tape load, midi out parameter change etc.
> >>
> >>Hope its not junk, help...
> >>
> >>--- In korgpolyex@yahoogroups.com, Marco Andreetta
> >><marco_andreetta@> wrote:
> >> >
> >> > From the schematic D2 looks like a polarity inversion
protection and
> >>every 1N400x serie diode will work (i.e.1n4001).
> >> >
> >> > "The board lights up but no sound" it's another problem, not
related
> >>to d2, so check again the other connections carefully.
> >> >
> >> > bye,
> >> >
> >> > Marco.
> >> >
> >> >
> >> > funkymonkeypeter <funkymonkey3.14@> ha scritto:
> >>The leg on the D2 diode was kinda short and while
> >>attempting the
> >> > slayer mod i'm pretty sure i cooked it trying to get the solder to
> >> > hold. I checked the schematics and it is listed as just D2 (no
> >> > value). Board lights up but no sound. What should i replace it
with.
> >> > Next time i'll flip the board first to find a better spot for
my glob
> >> > of solder. The only marking on the diode is something that
looks like
> >> > a pointy radiation warning sign.
> >> >
> >> >
> >> >
> >> >
> >> >
> >> >
> >> > ---------------------------------
> >> >
> >> > ---------------------------------
> >> > L'email della prossima generazione? Puoi averla con la nuova
Yahoo!
Show quoted textHide quoted text
> >>Mail
> >> >
> >>
> >>
> >>
> >
>
> _________________________________________________________________
> Windows Live Hotmail. Even hotter than before. Get a better look now.
> www.newhotmail.ca?icid=WLHMENCA148
>
