emulatorII-list

I'll try again this weekend to confirm. To be honest, I'm having trouble figuring out what software to put on the SD card from my computer. It appears that I have to run the HxC floppy emulator software and export a file to my SD card, but I'm not sure the settings. And I'm not sure how or if I'm supposed to create foldres on my computer, or after I get it into the HxC. Perhaps that's my issue, I don't have the right software on my card. I spent a good couple days trying to figure it out.

--- In emulatorII-list@yahoogroups.com, "esynthesist" <esynthesist@...> wrote:
>
> Did the ID2/Drive A setting NOT work in your setup with the HxC on Drive 2 ?
> 
> Because as far as I remember, with all tests I have been doing for Jeff on my EII it really didn't matter if I selected Drive A or Drive B on the J3 jumper array. The only consequence of this choice seemed to be that I had of course to select the same "drive" on the SD HxC after booting the SD HxC (i.e. when the firmware asks on its display which drive to use, A or B, one should select the drive that was chosen on the J3 jumper, A or B)
> 
> The ID0->3 choice (either on Drive A or B) is more important because it tells the HxC which 'drive select' line on the Shugart 34 pin interface should be used for activating the HxC. This is a choice on the actual physical/electrical level. 
> 
> But I can do the test again during the weekend - for sure I don't want to give wrong information here :-)
> 
> Anyway: ID2/Drive B will work (too) ! 
> 
> ///E-Synthesist
>   
> 
> --- In emulatorII-list@yahoogroups.com, "system_700" <isatellite@> wrote:
> >
> > >> Set the J3 jumper of the HxC to "ID2/DriveA" (see manual of HxC) <<
> > 
> > I tried following these instructions this weekend, and I think the above may be incorrect. When I look at the HxC manual, it appears to indicate that if you install the HxC in Drive 2, you need to set the J3 jumper to ID2/Drive B, not ID2/Drive A. Please verify.
> > 
> > Rod
> > 
> > --- In emulatorII-list@yahoogroups.com, "esynthesist" <esynthesist@> wrote:
> > >
> > > Assuming that your upper drive is Drive 1 and the lower one is Drive 2:
> > > - Drive 1 = floppy drive --> use the "untwisted connector" of the twisted cable.
> > > - Drive 2 = SD HxC --> use the "twisted connector" of the twisted cable.
> > > - Set the J3 jumper of the HxC to "ID2/DriveA" (see manual of HxC)
> > > - Don't change any jumper on the floppy drive, but make sure you use the floppy drive which was on Drive 1 originally. 
> > > 
> > > If the orginal Drive 1 floppy drive is broken, and you want to use the other one now as Drive 1, you'll have to change a jumper on the drive, unless you use the HxC as Drive 1 and the floppy drive as Drive 2. In the latter case the configuration will be:
> > > - Drive 1 = SD HxC --> use the "twisted connector" of the twisted cable.
> > > - Drive 2 = floppy drive --> use the "untwisted connector" of the twisted cable.
> > > - Set the J3 jumper of the HxC to "ID3/DriveA" (see manual of HxC)
> > > In this configuration it it still possible to copy banks from floppy to HxC, but not using the "Copy Disk" function. You'll have to load the bank and do a "Save Bank" to "Disk 1"
> > > 
> > > Note: I didn't test the above configurations, I just derive them from the documentation I have...  
> > > 
> > > ///E-Synthesist 
> > > 
> > > 
> > > --- In emulatorII-list@yahoogroups.com, "erwanquinquin" <erwanquinquin@> wrote:
> > > >
> > > > 
> > > > i have test the new firmware. Read and write work very well, so nice. But it is difficult to find the good IDE 34 pin cable. I would like to set the floppy drive as the upper drive ( to copy all my library on the hxc ) but I don't know how to set the jumber on the floppy drive cause of the "twisted" cable...
> > > >
> > >
> >
>