emulatorII-list

Hey Mike,

It plays back non-distorted but very low in volume, barely-audible low. And that's with the master volume cranked up to max.  My thought is that if the A/D would be bad, that the audio would be somewhat scratchy, distorted or so. But the fact that the audio basically sounds "intact" gives me hope that it might be a dry joint as you mentioned...  

I might just take it to my tech as this is a bit over my head..

Thanks Mike!

George





--- In emulatorII-list@yahoogroups.com, Mike de Vries <mrjdevries@...> wrote:
>
> When you play the audio back, and turn it up heaps, how does it sound? (Thin / dull / distorted etc)
>  
> Hopefully it's a dry joint or a dud op-amp..
>  
> When you are in the "Sample" page, and playing a sound into it, does the sound come back out the EII at normal (Non distorted etc) volume?
> 
> Regards
> Mike
> --- On Wed, 22/7/09, George <trickstar303@...> wrote:
> 
> 
> From: George <trickstar303@...>
> Subject: [emulatorII-list] Re: Sampled sound very low in volume.
> To: emulatorII-list@yahoogroups.com
> Received: Wednesday, 22 July, 2009, 2:51 AM
> 
> 
>   
> 
> 
> 
> Mike,
> 
> Thanks for the response. I'm aware of the gain settings on page 3 and tried various settings from 0 to 40db. I also metered the input audio close to max, just a bit under the clipping point. 
> 
> What's next?
> 
> George
> 
> 
> --- In emulatorII-list@ yahoogroups. com, Mike de Vries <mrjdevries@ ...> wrote:
> >
> > this souds obvious, but is the input gain high enough? (Not just the knob, but the gain setting... "SAMPLE  page 3 )
> > Whats it metering on your EII when you are sending audio to it?
> >  
> > If it says "Sample is good" that just means the sample didn't clip while sampling.. 
> > 
> > --- On Tue, 21/7/09, George <trickstar303@ ...> wrote:
> > 
> > 
> > From: George <trickstar303@ ...>
> > Subject: [emulatorII- list] Sampled sound very low in volume.
> > To: emulatorII-list@ yahoogroups. com
> > Received: Tuesday, 21 July, 2009, 9:53 AM
> > 
> > 
> >   
> > 
> > 
> > 
> > Hi,
> > 
> > After I sample a sound, it plays back very low in volume. During the metering/ gain adjusting process the input audio is looped thru in it's normal volume as well as during the sampling process. Once the "Sample is Good" message pops up and I try to play the sound, it's barely audible. 
> > 
> > Could this be a bad A/D converter? Anyone?
> > 
> > Thanks.
> > 
> > George
> > 
> > 
> > 
> > 
> > 
> > 
> > 
> > 
> > 
> > 
> > 
> > 
> > 
> > 
> > 
> > 
> > 
> > ____________ _________ _________ _________ _________ _________ _
> > Access Yahoo!7 Mail on your mobile. Anytime. Anywhere.
> > Show me how: http://au.mobile. yahoo.com/ mail
> > 
> > [Non-text portions of this message have been removed]
> >
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
>       ____________________________________________________________________________________
> Access Yahoo!7 Mail on your mobile. Anytime. Anywhere.
> Show me how: http://au.mobile.yahoo.com/mail
> 
> [Non-text portions of this message have been removed]
>