HI,
i try to calibrate the sliders/Lever with Lower Function A7, A8, A9.
But he Polaris Sliders still works from 2/4 to 4/4 range.
For example, if i move the master
slider Volume from 4/4 to 3/4 the volume goes perfectly down, but when
slider master volume move from 2/4 to 1/4 volume quickly goes down.
This is for all the lever on panel.
The two lever ( Bender ) near keyboard seem to work good.
I have also problem to do this operation :
R45 on Main Board -- ADC Range
Lower Function D 4
LED in master section do not light up !
I try to turn the R45 Clockwise and counterclockwise but nothing seems to work .
I also do not understand how to proceed to adjust the " lever assembly " voltage that should be between 2,0 and 3,0 volt.
What is the lever assembly ?
The adjust.doc manual means lever = Bender ?
Best regards.
Mario
Parma
Italy
From: "sukhoy27@..." <sukhoy27@...>
To: Chroma <chromapolaris@yahoogroups.com>; Chroma <chromapolaris@yahoogroups.com>
Sent: Friday, January 4, 2013 7:08 PM
Subject: Re: [chromapolaris] Slider front panel not working properly
To: Chroma <chromapolaris@yahoogroups.com>; Chroma <chromapolaris@yahoogroups.com>
Sent: Friday, January 4, 2013 7:08 PM
Subject: Re: [chromapolaris] Slider front panel not working properly
Thanks You Paul !
I misunderstanding the Lower Function A 7 !
I thought it is referred only to left keyboard 2 lever !!
I'll let You know after procedure !
Mario
I misunderstanding the Lower Function A 7 !
I thought it is referred only to left keyboard 2 lever !!
I'll let You know after procedure !
Mario
From:
Paul D. DeRocco <pderocco@...>;
To: <chromapolaris@yahoogroups.com>;
Subject: RE: [chromapolaris] Slider front panel not working properly
Sent: Wed, Jan 2, 2013 9:44:06 PM
LOWER FUNCTION, A, 7, then move both levers through their entire ranges,
then press LOWER FUNCTION again. It's probably a good idea to do all the
calibration procedures, if you can manage to follow them in English.
Sometimes it's possible to take a slider apart, clean it, and put it back
together successfully, but not always. It's easier just to replace it. John
Leimseider had some available back in September. If he doesn't respond to
your query on the mailing list, you could contact him directly at
john.leimseider@.... But try doing all the calibrations first.
--
Ciao, Paul D. DeRocco
Paul mailto:pderocco@...
To: <chromapolaris@yahoogroups.com>;
Subject: RE: [chromapolaris] Slider front panel not working properly
Sent: Wed, Jan 2, 2013 9:44:06 PM
So what's wrong with the bend? Did you do the lever calibration? That's> From: sukhoy27@...
>
> I just complete to replace the membrane switch Panel , thanks
> to Paul very detailed Photo instructions , and so my Polaris
> model 301420 still play like new !!!
> But probably because is has bend not working for 5/6 years
> something happens and the panel slider from Master Volume to
> the assignable control when moved works only 40% . The
> sliders that has yo be in the centre working position works
> only when moved down , but not moved up.
LOWER FUNCTION, A, 7, then move both levers through their entire ranges,
then press LOWER FUNCTION again. It's probably a good idea to do all the
calibration procedures, if you can manage to follow them in English.
Sometimes it's possible to take a slider apart, clean it, and put it back
together successfully, but not always. It's easier just to replace it. John
Leimseider had some available back in September. If he doesn't respond to
your query on the mailing list, you could contact him directly at
john.leimseider@.... But try doing all the calibrations first.
--
Ciao, Paul D. DeRocco
Paul mailto:pderocco@...