Hi Jim,
I had a similar problem.
NooS means no operating system. I contacted Behringer and over some time - my fault entirely - I've just got it all sorted out. it involved having to go into bootlegger mode and reinstallling to software. Our exchange of email is below. I hope it helps.
David
1:- Hello David,
Thanks for writing to us.
"NoOS" stands for "No operating system". Attached please find the "BCF2000 upgrade manual". Please take a look on page 2 (bottom) & page 3. You'll find all required information on how to reload a firmware version on the BCF2000.
You can use a freeware program like "MIDI OX" www.midiox.com to transfer the Syx file.
2:- Dear David,
Thanks very much for writing to us.
Please download the latest firmware version from our webpage - 1.10.
This is a SYX (MIDI Sysex) file. Use MIDIOX (www.midiox.com) to send the SYX file to the BCF2000 (which is switched into bootloader mode).
The upgrade is only possible via MIDI connections. Please make sure that the BCF2000 is connected in both directions (MIDI Out to MIDI In & vice versa).
--- In bc2000@yahoogroups.com, "Jim Burrill (UK)" wrote:
>
> I've ordered another MIDI interface Karl and I will take it from
> there. It's a Midiman interface? Hope this one will work.
> Thanks for the help Karl.
>
> Jim
>
>
>
>
> --- In bc2000@yahoogroups.com, "Karl Lurman" karl.lurman@ wrote:
> >
> > Sounds like a dodgy midi cable. Unless you don't have the cable
> going
> > in correctly. It should go midi out (from the usb) to midi in (on
> the
> > bcr) and midi out (on the bcr) to midi in (on the usb). I too have
> had
> > the misfortune of using the behringer update proggy and had the same
> > NOOS experience. Luckily I was able to borrow a USB->midi adaptor,
> but
> > prior to that I tried to make my own midi cable (with a few loose
> > wires I had around the place). It seemed as though it was working,
> > because the midi lights would flash when I tried to send the sysex
> > file to the unit, however the update would not occur. It was only
> > until I used a proper cable that I saw the progress indicator on the
> > index (an increasing number and small cycling animation).
> >
> > Good luck dude!
> > Karl
> >
> > On Tue, Mar 25, 2008 at 4:07 AM, Jim Burrill (UK) smogthemog@
> wrote:
> > >
> > >
> > >
> > >
> > >
> > >
> > > I have just purchased BCR2000 off of Ebay and all was well when I
> got
> > > it. I required it for live MIDI control of Mamba Black Laser show
> > > software. It was running v1.07 OS when I got it and upon trying
> to
> > > update it using the POXY Behringer update program it now only
> reads
> > > NooS in the LED display :(
> > > This now means I have no USB acsess and can only OS dump via
> MIDI from
> > > the PC. Well I have tried that about 50 times now but to no
> avail.
> > > I am running Windows XP Pro SP2 and with an Ebay bought USB to
> MIDI
> > > interface cable.
> > > I have pressed the STORE/LEARN buttons opon switch on (to give
> the LOAD
> > > sequence) and dumped the file to it via MIDI but nothing. The
> display
> > > dosen't change at all. The MIDI light flashes but nothing at the
> end.
> > >
> > > Any help will be greatly appreciated.
> > > Thanks
> > > Jim Burrill
> > >
> > >
> >
>