Homebrew_PCBs

Hi. I just got my lexmark e260d to convert to a pcb printer. In step 4
of the instructables guide it says


"You should now just be left with two bare green plastic pieces
[Photo]."


I am fairly certain it should be.


"You should now just be left with two bare gray plastic pieces
[Photo]."


Thanks for the guide. I get my parts from mcmaster tomorrow so I am
excited to finish it. I also ported your pseudocode to an arduino
library I figure that might help some people out. I will post here once
I can test it.




--
Matthew O'Gorman
BM: BM-2D7WS1iu3wNo66sLVwd4CcZ5sBHbn8CYwR
TorChat: 5w3dtk7nhkkijcpc
Site: https://b.rldn.net
Xim/Email: mog@...
mog@rldn:~$ fortune wisdom -s|boxes
/************************************************************/
/* He is truly wise who gains wisdom from another's mishap. */
/************************************************************/




[Non-text portions of this message have been removed]

Which Instructables guide?

"alienrelics@... [Homebrew_PCBs]" <Homebrew_PCBs@yahoogroups.com>
writes:

> Which Instructables guide?
>
> Steve Greenfield AE7HD

Sorry I was referring to this
http://www.instructables.com/id/Modification-of-the-Lexmark-E260-for-Direct-Laser--1/?ALLSTEPS
instructables link. It is mlerman's project.




--
Matthew O'Gorman
BM: BM-2D7WS1iu3wNo66sLVwd4CcZ5sBHbn8CYwR
TorChat: 5w3dtk7nhkkijcpc
Site: https://b.rldn.net
Xim/Email: mog@...
mog@rldn:~$ fortune wisdom -s|boxes
/*******************************************************************************/
/* If you live long enough, you'll see that every victory turns into a defeat. */
/* -- Simone de Beauvoir */
/*******************************************************************************/




[Non-text portions of this message have been removed]

Hi Matthew,

I'm not sure where that line of text is. However, I am somewhat colorblind and can easily have mistaken gray for green. Quite a few people have made this conversion by now, so I can say without reservation that it works! When I started investigating DLP in 2010, I wasn't so sure!

Mark


-----Original Message-----

>From: "Matthew O'Gorman mog@... [Homebrew_PCBs]" <Homebrew_PCBs@yahoogroups.com>
>Sent: Feb 17, 2015 6:01 AM
>To: Homebrew_PCBs@yahoogroups.com
>Subject: [Homebrew_PCBs] Correction to lexmark e260d printer guide
>
>Hi. I just got my lexmark e260d to convert to a pcb printer. In step 4
>of the instructables guide it says
>
>
>"You should now just be left with two bare green plastic pieces
>[Photo]."
>
>
>I am fairly certain it should be.
>
>
>"You should now just be left with two bare gray plastic pieces
>[Photo]."
>
>
>Thanks for the guide. I get my parts from mcmaster tomorrow so I am
>excited to finish it. I also ported your pseudocode to an arduino
>library I figure that might help some people out. I will post here once
>I can test it.
>
>
>
>
>--
>Matthew O'Gorman
>BM: BM-2D7WS1iu3wNo66sLVwd4CcZ5sBHbn8CYwR
>TorChat: 5w3dtk7nhkkijcpc
>Site: https://b.rldn.net
>Xim/Email: mog@...
>mog@rldn:~$ fortune wisdom -s|boxes
>/************************************************************/
>/* He is truly wise who gains wisdom from another's mishap. */
>/************************************************************/
>
>
>
>
>[Non-text portions of this message have been removed]
>
>
>
>
>------------------------------------
>Posted by: Matthew O'Gorman <mog@...>
>------------------------------------
>
>Be sure to visit the group home and check for new Links, Files, and Photos:
>http://groups.yahoo.com/group/Homebrew_PCBs
>------------------------------------
>
>Yahoo Groups Links
>
>
>