The 3% wasn't my first chioce, but it was redily available and at the
price, I wouldn't have felt bad if it didn't work. Cost wise it's
about the same as 30% at $10 a quart.
I don't *want* to throw it away, I was just comparing cost to Feric
Chloride.
After I etched for a while, it turned a darker shade of green, just
like you said. The I added some more H2O2, (1/2 cup) it got very
pale, I assumed it was from the excess water diluting it. But whith
what you said about chlorine gas as a sign of too much H2O2, maybe
it's not as bad as I thought.
Please put a number to the bubble size, 10-20 thou? 50-100 thou? (I
was getting some in the 50-100 thou range). It got warm, but not
boiling (maybe 110 F)
What kind of tank setup do you use?
I'm thinking of getting an appropreate size tupperware canister and
setting up a bubbler. Not so much for the oxygenation, but the
agitation while etching.
What do you have for a board holder?
Thanks, you've been incredably helpfull.
-Denny
--- In Homebrew_PCBs@yahoogroups.com, Stefan Trethan
<stefan_trethan@g...> wrote:
price, I wouldn't have felt bad if it didn't work. Cost wise it's
about the same as 30% at $10 a quart.
I don't *want* to throw it away, I was just comparing cost to Feric
Chloride.
After I etched for a while, it turned a darker shade of green, just
like you said. The I added some more H2O2, (1/2 cup) it got very
pale, I assumed it was from the excess water diluting it. But whith
what you said about chlorine gas as a sign of too much H2O2, maybe
it's not as bad as I thought.
Please put a number to the bubble size, 10-20 thou? 50-100 thou? (I
was getting some in the 50-100 thou range). It got warm, but not
boiling (maybe 110 F)
What kind of tank setup do you use?
I'm thinking of getting an appropreate size tupperware canister and
setting up a bubbler. Not so much for the oxygenation, but the
agitation while etching.
What do you have for a board holder?
Thanks, you've been incredably helpfull.
-Denny
--- In Homebrew_PCBs@yahoogroups.com, Stefan Trethan
<stefan_trethan@g...> wrote:
> On Thu, 08 Jan 2004 22:54:28 -0000, dkesterline <desterline@t...>wrote:
>out.
> > Well, I finaly got around to buyng a jug of acid and trying this
> >$2.95
> > I bought a gallon of HCL (31.25%) from my local hardware store,
> > (USD) Stopped by the Pharmacy and bought a quart of 3% H2O2 for$0.94.
>circuit board
> you should not have bought the 3% stuff ;-)
>
> >
> > Plastic container, about 1/4 cup acid, stuck in a piece of
> > and started adding H2O2. At about 1/2 cup I could see some greentinge
> > and the copper started changing. I poured in a litle more (about3/4 cup
> > total) and the copper etched in about 8 minutes.slowed
> >
> > About 1 cup total of etchant removed about 30 sq inches of copper
> > (surplus scrap, but I think 1 oz) before it was quite dark and
> > considerably.being used
> >
> > I think the amount of water in medical grade would prevent it
> > to recharge the etchant (to much dilution) but it certainlystarted it
> > fine.still
>
> may well be (therefore my comment above)
>
> >
> > Even if I had to throw it away instead of recharging it, this is
> > *much* cheaper than Feric Chloride. At these ratios a 94 centquart of
> > medical H2O2 and a cup of acid would replace a $12 quart of Fericof nasty
> > Chloride.
> >
> do not, save the environment ;-)
>
> > I did notice that it was much more unpleasant to be around (lots
> > fumes) But I can work around that.
>
> too much h2o2 if you got cloring gas.
> just bright green and TINY bubbles, not boiling like hell ;-)
>
> >
> > Thanks
> > -Denny
> >
>
> Nice it worked.
>
> ST