--- In DigitalBlackandWhiteThePrint@y..., "Tyler Boley" <tyler@t...> wrote: > --- In DigitalBlackandWhiteThePrint@y..., "Martin Wesley" > <mwesley250@e...> wrote: > >.....Given an established film exposure and development process. (I > > am inclined to leave mine as it is in case I want to take a neg > back > > into the darkroom.) > > I haven't changed mine for scanning Martin, my negs are pretty dense. > I understand people are altering their exposure/ > developement to optimize for scanning, but I'm hesitant to go that > route, and I'm dead tired of calibrationg! It seems to > work fine this way, sometimes I scan difficult negs as tranperancies, > which can really help. At least that is one place I have stopped experimenting. (I think.) > > > > The difficulty seems to be in the amount of expertise and equipment > > required to close the feedback loop from monitor to print in a > series > > of iterations to bring it all to a workable point. > > It really didn't take that long to learn, most of it is on Dan's > pages. The equipment is another problem, it's hard to justify the > cost of a photospecrometer, but since I was beta testing profiling > software and inks, I went ahead with it. I was trying to > develope curves all kinds of ways, by eye, or with a scanner. That > was ok up to a point. I sent Dan a case of Absolute in > exchange for some ink/paper setup measurements and everything I was > battling fell into place, that convinced me I had to > have one. It can be done without one, but it takes a lot more time > and some problems are just never found, I'd rather make > prints. I didn't hear from him for several months, so maybe that was > a bad bad thing... > What takes more time and learning, and is far more interesting, is > the nature of ink on paper and how to find problems and > create something beautiful. It's an ongoing process, just like > traditional printing. What do you recommend for an instrument to do this? I have seen the Spectrocam at InkJetMall for $1,400 and the X-RiteColor Digital Swatchbook also about $1,400. Is there a lower price point to get into this? I suspect there is a sense that since we are doing B&W, things like color calibration are not so important. The deeper I get into this the more that seems untrue. In fact it may be even more important as subtle shifts may be more visible than they are in color printing. I assume that this type of measurement and adjustment is also valid for printing through the Epson driver as well as through the RIP? > > > > I have a couple of questions. When you are adjusting in 8-bit how > do > > you do your proofing? > > I just save where I am, flatten the file and size it to what I want > to see as a test, save it as a temp/test, run it through the > grayscale-CMYK-seps action, and print. Sometimes I use a cheaper > paper like EAM because it takes the ink similarly, but I > still wind up needing to see one on the real paper because it feels > so different, even if it's the same tonaly. > > > You mention loading all of the layer and > > adjustment information from the 8-bit work file back to the 16- bit > > file, how is this done? > > > I think Bruce Fraser has an article about it somewhere. You have your > 8 bit file with adjustment layers, and your 16 bit file > open at the same time. In the 8 bit, open the adjustment layer and > save the curve (level, whatever it is) to the desktop, > leave that layer selected. Switch to your 16 bit file and go to "load > selection", you will have the option of loading the layer > mask from the 8 bit file layer, do it. Open curves and load the one > on your desktop that was saved. Now do that with each > adjustment layer. Note that only edits available in 16 bit can be > done this way, but those are all I generally need. > After you've done this a few times, it goes real quick. I think it is past time for me to get a copy of Real World Photoshop (Blatner and Fraser). In playing with this I notice that the histogram is filled and smoother in comparing the adjusted 16-bit file to the 8-bit. This is really the work around that allows you to "stay" in 16-bit Grayscale to do all you your level adjustments. Since you are printing with the Piezo inks can you give us a comparison of the results using your system verses just printing through the Piezo driver? I believe in your last post you said you drop down to 8-bit just before printing. Is this required to work with the RIP or is this just to reduce file size at this point? This is all very enlightening stuff. Thank you! Martin
Message
Re: CMYK workflow
2001-08-28 by Martin Wesley
Attachments
- No local attachments were found for this message.