Synth-DIY Yahoo! Groups Archives

Thread

Re: [AN1x-list] Despoiling the An1x

2001-12-20 by James R. Acker

I don't think anything is going to last very long if you use the effect much. I'm trying to think of something though...


Jim

=============================================================
Please check out my original music at my site http://home.online.no/~jacker
-James R. Acker-
----- Original Message -----

Show quoted textHide quoted text

From: "tuskermusic" <tuskerfort@...>
To: <AN1x-list@yahoogroups.com>
Sent: Thursday, December 20, 2001 2:31 PM
Subject: [AN1x-list] Despoiling the An1x


> Fellas I like the An1x ribbon, but I dont get enough tactile 
> feedback. I am considering adding four "points" along the ribbon to 
> help me out. Two of the points would be to the left of the center and 
> two to the right.
> 
> I have considered dropping paint (too permanent and ugly), sticking 
> little bits of paper (too easy to move) etc.
> 
> I am wondering if anyone has ideas. 
> 
> Thx,
> 
> Jerry
> 
> 
> 
> Community email addresses:
>   Post message: AN1x-list@yahoogroups.com
>   Subscribe:    AN1x-list-subscribe@yahoogroups.com
>   Unsubscribe:  AN1x-list-unsubscribe@...m
>   List owner:   AN1x-list-owner@yahoogroups.com
> 
> Shortcut URL to this page:
>    http://groups.yahoo.com/group/AN1x-list
>  
> 
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/ 
> 
> 
>

Despoiling the An1x

2001-12-20 by tuskermusic

Fellas I like the An1x ribbon, but I dont get enough tactile 
feedback. I am considering adding four "points" along the ribbon to 
help me out. Two of the points would be to the left of the center and 
two to the right.

I have considered dropping paint (too permanent and ugly), sticking 
little bits of paper (too easy to move) etc.

I am wondering if anyone has ideas. 

Thx,

Jerry

Re: [AN1x-list] Despoiling the An1x

2001-12-20 by Bruce Wahler

Jerry,

>Fellas I like the An1x ribbon, but I dont get enough tactile
>feedback. I am considering adding four "points" along the ribbon to
>help me out. Two of the points would be to the left of the center and
>two to the right.
>
>I have considered dropping paint (too permanent and ugly), sticking
>little bits of paper (too easy to move) etc.
>
>I am wondering if anyone has ideas.

How about Elmer's Glue?  Wood glue dries almost transparent, it only 
semi-bonds to plastic, and it leaves no permanent marks or crazing when 
removed.

Also, I would suggest adding eight points, centered above and below the 
middle, so that you don't wear them off every month or so:

(Lousy ASCII drawing follows)

-------------------------------------------
|       o       o          o       o      |
|                                         |
|       o       o          o       o      |
-------------------------------------------

Regards,

-BW

--
Bruce Wahler
Design Consultant
Ashby Solutions   www.ashbysolutions.com
CloneWheel Support Group and HiNote moderator
978.386.7389  voice/fax
bruce@...

RE: [AN1x-list] Despoiling the An1x

2001-12-21 by Aireq

It would be best to lay something over the entire strip. Get some slicker
vinyl at a fabric shop and cut a strip out that is the side of the ribbon.
Glue or attached whatever you want to the vinyl. Other materials could be
used obviously.

aireq

Show quoted textHide quoted text

-----Original Message-----
From: James R. Acker [mailto:jacker@...]
Sent: Wednesday, December 19, 2001 6:41 PM
To: AN1x-list@yahoogroups.com
Subject: Re: [AN1x-list] Despoiling the An1x


I don't think anything is going to last very long if you use the effect
much. I'm trying to think of something though...


Jim

=============================================================
Please check out my original music at my site http://home.online.no/~jacker
-James R. Acker-
----- Original Message -----
From: "tuskermusic" <tuskerfort@...>
To: <AN1x-list@yahoogroups.com>
Sent: Thursday, December 20, 2001 2:31 PM
Subject: [AN1x-list] Despoiling the An1x


> Fellas I like the An1x ribbon, but I dont get enough tactile
> feedback. I am considering adding four "points" along the ribbon to
> help me out. Two of the points would be to the left of the center and
> two to the right.
>
> I have considered dropping paint (too permanent and ugly), sticking
> little bits of paper (too easy to move) etc.
>
> I am wondering if anyone has ideas.
>
> Thx,
>
> Jerry
>
>
>
> Community email addresses:
>   Post message: AN1x-list@yahoogroups.com
>   Subscribe:    AN1x-list-subscribe@yahoogroups.com
>   Unsubscribe:  AN1x-list-unsubscribe@yahoogroups.com
>   List owner:   AN1x-list-owner@yahoogroups.com
>
> Shortcut URL to this page:
>    http://groups.yahoo.com/group/AN1x-list
>
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>
>



Community email addresses:
  Post message: AN1x-list@yahoogroups.com
  Subscribe:    AN1x-list-subscribe@yahoogroups.com
  Unsubscribe:  AN1x-list-unsubscribe@yahoogroups.com
  List owner:   AN1x-list-owner@yahoogroups.com

Shortcut URL to this page:
   http://groups.yahoo.com/group/AN1x-list


Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/

The Yamaha AN1x Synthesizer mailing list

Re: [AN1x-list] Despoiling the An1x

Re: [AN1x-list] Despoiling the An1x

Despoiling the An1x

Re: [AN1x-list] Despoiling the An1x

RE: [AN1x-list] Despoiling the An1x

Move to quarantaine